Where is the USB port in the Beijing BJ40?

1 Answers
DelPatrick
07/29/25 10:57pm
The USB port in the Beijing BJ40 is located inside the center armrest box. Exterior Design: As a self-developed SUV model, the Beijing 40 features straight and rugged lines that outline its boxy and bold body. The five-square-hole design on the front grille is a signature symbol of Beijing Auto's "Off-Road Family." The exaggerated front and rear bumpers, along with the prominent wheel arches, further enhance the unique wild beauty of the Beijing 40. Interior Features: The Beijing 40 is equipped with a wide-angle reversing radar, electrically foldable exterior rearview mirrors, overhead audio, interior lighting, and air vents that also function as beverage coolers, significantly enhancing the model's convenience and usability. Powertrain: The Beijing 40 is powered by a 2.4-liter engine, delivering 105 kW of power and a maximum torque of 217 Nm. Among engines with a displacement of 2.5 liters or less in the domestic market, this G4CA-2.4L gasoline engine's low-speed high-torque performance is most suitable for off-road vehicles.
Was this review help?
8
4
Share
More Forum Discussions

How to Connect a Phone to Crown Car Bluetooth?

Turn on the Bluetooth in your phone settings to ensure it is enabled. Enable the car's Bluetooth, then search for your phone via the car's Bluetooth and connect once found. Go to Settings > General > About > Name, tap on the car's Bluetooth name, and then proceed to pair.
15
4
Share

How to Adjust the Mixture Ratio of a Scooter Carburetor?

First, prop up the vehicle, turn the air-fuel mixture screw clockwise until it bottoms out, then back it off by 1/2 turn. Rotate the idle screw clockwise until the spring beneath the idle screw is properly compressed (preferably around 4000 rpm). Start the engine, stop rotating the air-fuel mixture screw, and let the engine continue running. Slowly turn the idle screw counterclockwise to reduce the idle speed. After completing the above adjustments, while the engine is still running, quickly open and close the throttle by hand.
3
2
Share

How to Remove the Rear Emblem?

First, use a hairdryer to heat the rear emblem of the car, then use a small knife to cut a small slit in the adhesive between the emblem and the car paint. Prepare a piece of string and a bottle of adhesive remover. Use the string to scrape off the emblem, then wipe off the 3M adhesive with the adhesive remover.
4
4
Share

Should the Lamando 280 use 5W30 or 5W40 engine oil?

For the Volkswagen Lamando 280, it is necessary to use Volkswagen's original VW-50200 or higher 5W-40 engine oil. If you wish to change the oil during later maintenance, you can choose brands such as Shell, Mobil, or Castrol, but ensure the oil meets the VW-50200 or higher 5W-40 specification. The viscosity of engine oil changes with temperature, so special attention should be paid to its performance under both low and high temperatures. For example, in 5W-30, the first number indicates low-temperature fluidity. 5W means it can withstand temperatures as low as -30°C. The smaller this number, the better the low-temperature fluidity, resulting in smoother cold starts for the car. The latter number represents the oil's kinematic viscosity at 100°C. A higher number means the oil can maintain its viscosity index better at high temperatures, which can also be understood as better lubrication performance under high-temperature conditions. The method for changing the engine oil in the Volkswagen Lamando 280 is as follows: Wait for the engine temperature to drop, allowing the oil to flow back into the oil pan. Use a wrench to loosen the oil drain plug and place an oil pan underneath to catch the old oil until no more oil flows out. Start the engine and let it run for 30 seconds to allow the oil in the main oil passages to drain. Use a specialized wrench to remove the oil filter. Apply some oil to the oil seal of the new oil filter and tighten it clockwise by hand. Add the new engine oil through the oil filler cap on the engine's valve cover. Typically, fill up to three-quarters of the oil container. Start the engine and let it run for 5 minutes, then check for any oil leaks around the oil drain plug and oil filter. If leaks are found, perform necessary repairs. After stopping the engine, pull out the oil dipstick and check that the engine oil level is within the standard range.
12
3
Share

How to Remove the Rear Seat of the New Santana?

To remove the rear seat of the Volkswagen New Santana, first detach the fixed buckle on the right side of the rear seat, then remove the fixed buckle on the left side. Next, separate the seat belt buckle of the rear seat, and the rear seat can be easily removed.
7
2
Share

How to Connect Bluetooth in Trumpchi GS4?

After starting the car, the Bluetooth on the car is turned on by default, so you only need to enable the Bluetooth function on your phone. In the phone's Bluetooth settings, set Bluetooth to "Visible to All" or searchable, which facilitates pairing between the phone and the car's Bluetooth. Search for Bluetooth devices on the phone, select the found device for pairing, the pairing password is: 0000, and the connection is successful after pairing is completed.
13
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.