Where is the USB port in the 2015 Audi A4?

Which region does the license plate 'Hei M' belong to?

Hei M is the license plate code for Suihua, Heilongjiang Province. The license plate codes for various regions in Heilongjiang Province are as follows: 1. Hei A - Harbin, Hei B - Qiqihar, Hei C - Mudanjiang, Hei D - Jiamusi, Hei E - Daqing, Hei F - Yichun. 2. Hei G - Jixi, Hei H - Hegang, Hei J - Shuangyashan, Hei K - Qitaihe, Hei L - Counties and county-level cities under Harbin. 3. Hei M - Suihua, Hei N - Heihe, Hei P - Daxing'anling Prefecture, Hei R - Heilongjiang Agricultural Reclamation Administration (Reclamation Area). Additional Information: The use of combinations of numbers and letters for license plate serial numbers should follow the prescribed order. When the utilization rate of a serial number combination exceeds 60%, the next combination method should be activated in sequence after approval by the provincial public security traffic management department and filing with the Traffic Management Bureau of the Ministry of Public Security. The utilization rate is the ratio of the total number of used serial numbers to the theoretical capacity of serial numbers.

3

Share

Does a car need brake fluid replacement?

Automobile brake fluid needs to be replaced. Below are the precautions for brake fluid replacement: 1. The replacement interval for brake fluid can be appropriately advanced or delayed based on vehicle usage, mileage, driving conditions, and brake responsiveness. Since new cars come with factory brake fluid of better quality, the service period can be extended slightly, generally requiring replacement after about 5 years. For normal vehicles, the replacement interval is approximately 2-3 years or around 50,000 kilometers. 2. When replacing brake fluid, do not opt for cheaper options; always choose high-quality brake fluid. Issues with brake fluid can significantly impact braking performance. 3. Automobile manufacturers typically recommend replacing brake fluid every 2-3 years because brake fluid is an alcohol-based oil product. Over time, moisture from the air can permeate into the brake fluid. If there's excessive moisture in the brake fluid, continuous braking could cause the brake system to overheat, potentially leading to brake fluid boiling and resulting in the serious consequence of brake failure.

3

Share

What should be paid attention to when driving on icy and snowy roads?

Precautions for driving on icy and snowy roads are as follows: 1. Start slowly and gently press the accelerator: On icy and snowy roads, difficulty in starting the vehicle is a common situation, especially for front-wheel-drive cars where the front wheels are prone to slipping, which can be very dangerous. Therefore, when starting on icy and snowy roads, the force applied to the accelerator should be lighter, and avoid pressing the accelerator too hard when starting. 2. Predict in advance to ensure safety: "Prediction" is essential when driving in snowy conditions, and it should be more important than usual. Snowfall can greatly affect driving visibility, making it even more necessary to judge the situation ahead in advance to avoid sudden steering or emergency braking. 3. Avoid sudden steering: When driving in snowy conditions, avoid sudden steering. Snowfall can cause snow and ice accumulation or muddy roads, significantly reducing tire grip. Sudden steering can cause the wheels to lose grip, making it impossible to complete the turning operation and leading to skidding. 4. Slow down and flash lights more when turning: Before entering a turn in snowy conditions, reduce the speed in advance and avoid braking to slow down after entering the turn. It is best to press the brake a few times before braking to alert the following vehicle to slow down and avoid a rear-end collision. 5. Do not panic in emergencies: If skidding or fishtailing occurs while driving, do not panic. At this time, gently release the accelerator and slightly correct the direction, continuously adjusting between steering and correcting, but not too much. Avoid slamming on the brakes when skidding or fishtailing, as this will not only be ineffective in slowing down but may also cause the vehicle to lose control.

2

5

Share

Can You Wash a Car Engine Bay with Water?

The car's engine bay undergoes very rigorous waterproofing treatment before leaving the factory. Therefore, many 4S shops or repair shops will directly rinse it with water—simply washing with water is not a problem. The main considerations for cleaning the engine bay with water are as follows: 1. Wait until the car engine has cooled down before washing, as the engine temperature is very high after prolonged operation, and rinsing with cold water may cause the engine to crack. 2. Do not use a high-pressure water gun to rinse the fuse box. Although the car undergoes certain waterproofing treatments during production, the fuse box may still risk short-circuiting or leakage when faced with high-pressure water rinsing. 3. After several years of car use, try to avoid washing the engine bay with water, as aging wiring issues may arise over time.

12

4

Share

How to Adjust the Jetta Seats?

Here are the methods to adjust the Jetta seats: 1. Pull the lever upward to move the seat forward or backward; 2. Pull the adjustment handle backward while adjusting the backrest to the desired angle to adjust the seat backrest; 3. Repeatedly lift or press the handle to adjust the seat to the appropriate height. Additional notes on seat adjustment: 1. Do not fold the seat backrest forward or backward while the vehicle is in motion. 2. When adjusting the seat backrest, keep hands, fingers, and other body parts away from the backrest pivot and adjustment mechanism to avoid pinching. 3. Avoid getting floor mats or other objects caught in the seat backrest pivot, as this may prevent the backrest from locking properly when returned to the upright position. 4. No passenger (whether adult or child) should sit on a seat with an improperly locked backrest or one that is excessively tilted forward.

2

1

Share

What is 36 psi in terms of tire pressure?

36 psi is equivalent to 2.5 bar tire pressure. psi refers to the unit of tire pressure, while bar is a unit of pressure. Tire pressure indicates the air pressure inside the tire. Hazards of excessive tire pressure: 1. Reduced tire friction and adhesion, affecting braking performance; 2. Causes steering wheel vibration and deviation, lowering driving comfort; 3. Accelerates wear on the central tread pattern, shortening tire lifespan; 4. Increases vehicle vibration, indirectly affecting the longevity of other components; 5. Overextends tire cords, reducing elasticity and increasing the load on the vehicle during driving; 6. Decreases puncture resistance, making tires more susceptible to damage from sharp objects like nails or glass, which can lead to internal cracks, blowouts, or tire bursts.

7

5

Share

Where is the USB port in the 2015 Audi A4?

Which region does the license plate 'Hei M' belong to?

Does a car need brake fluid replacement?

What should be paid attention to when driving on icy and snowy roads?

Can You Wash a Car Engine Bay with Water?

How to Adjust the Jetta Seats?

What is 36 psi in terms of tire pressure?

How to Solve the Problem of Water in Car Taillights?

What do the three electric components of new energy vehicles refer to?

What Causes Difficulty in Cold Starts During Winter?

What is the purpose of car washing?