Where is the USB port for music in the 2006 Reiz?

2 Answers
Sue
07/29/25 9:18pm
The USB port for music in the 2006 Reiz is located inside the car's center armrest. USB car chargers, often simply referred to as USB car adapters, leverage the widespread use of USB interfaces for various charging purposes. Precautions when using car USB ports: Charging current "can be higher but not lower": The output current of the car charger should not exceed the maximum rated input power of the phone. For example, a car charger with an output of 5V/2.1A will supply 1A to a phone with a maximum rated input of 5V/1A and 2A to a tablet, enabling faster charging. However, if a car charger with an output of 5V/0.5A is used for the same phone, it will only supply 0.5A, resulting in slower charging, significant overheating, and potential long-term damage to the phone's battery. Avoid using a car charger if the car has a USB port: Most USB ports in cars are designed for audio data transfer, with a typical current output of 5V/0.5A. If the current is insufficient, it can damage the connected device.
Was this review help?
3
5
Share
GideonDella
08/15/25 7:52pm
My 2006 Toyota Reiz is a car I've driven for many years. The USB port isn't actually in a conspicuous location because factory-installed USB ports weren't standard back in those days. I've searched several times and found that there might be a reserved slot near the front of the center armrest, but it looks more like an AUX audio input rather than a true USB port. For listening to music, it's best to use an AUX cable to connect to your phone or MP3 player, or buy a cigarette lighter USB adapter with an FM transmitter to receive music. When I usually check, I first open the armrest lid and then feel around the bottom or sides for any port markings; if there's nothing, don't rush—ask on forums or simply upgrade to a new audio system for more convenience. Remember, the 2006 model has an older design, so direct USB playback isn't practical. Be cautious about battery drain when making modifications to avoid affecting driving safety. Music can relax you while driving, but make sure the connection is stable.
Was this review help?
19
3
Share
Expand All
More Forum Discussions

Does a small car need to undergo an on-road inspection in its sixth year?

At the end of the sixth year, which means when the seventh year is about to begin, the car must undergo an on-road inspection. Here are some relevant details about the on-road inspection for small cars: 1. Exhaust emission test: Within one week before the inspection, avoid using gasoline from small gas stations. Instead, use fuel from reputable sources like PetroChina or Sinopec. It is best to use a higher octane rating; for example, if you usually use 92, switch to 95 during this period to effectively increase the pass rate of the exhaust emission test. 2. Lighting system inspection: This mainly checks the brightness and angle of the lights. Generally, as long as the lights are original and unmodified, they will pass. However, some people modify their lights, such as replacing halogen lights with xenon headlights without adding a lens, which can result in the headlight angle failing the inspection. Others may modify their brake lights to flash rapidly, which is also not allowed. Therefore, any modified lights must be reverted to their original state before the inspection.
20
3
Share

What are the reasons for the sudden failure of low beam lights?

The reasons for the failure of low beam lights are as follows: 1. Dead battery: You can check the battery power by pressing the horn at this time. 2. Bulb damage: Most bulbs also have a certain usage cycle. When they are close to being scrapped, the light intensity does not meet the standard, and at the same time, they generate heat until the filament burns out. In addition, there are some other reasons, such as the headlight assembly being prone to water ingress after the vehicle wades through water. When a hot bulb comes into contact with water droplets, the temperature drops sharply, which may cause the bulb to crack and break. 3. Blown fuse: Most low beam fuses can be found in the fuse box in the engine compartment or the fuse box on the left side of the instrument panel. The fuse is located behind the fuse box cover, and you can use a special clip to remove and inspect it. 4. Fault in the low beam adjustment circuit: It may be that the light control switch has a problem. In this case, you can go to the shop for repair and check whether the light switch control logic is abnormal.
9
5
Share

How Many Cylinders Does the Fista Engine Have?

Fista is equipped with a four-cylinder engine. Related introduction: 1. Brand introduction: A sporty sedan under Beijing Hyundai, positioned as a "high-performance tech-charming sedan," it is a high-performance sports car specifically designed for the Chinese market. It is the first mass-produced vehicle to adopt Hyundai's latest global design philosophy. 2. Power: Equipped with a turbocharged engine, it can accelerate from 0 to 100 km/h in just 7.6 seconds. 3. Vehicle dimensions: 4.6 meters in length, 1.79 meters in width, 1.42 meters in height, with a wheelbase of 2.7 meters. 4. Fuel consumption: 5.2L/100km.
10
4
Share

Which is more reasonable, tire pressure display or tire pressure warning?

Tire pressure display is more reasonable. The tire pressure display allows you to visually see the tire pressure, while the tire pressure warning is just an alarm system that alerts you when the pressure is too high or too low. Therefore, the tire pressure display is more intuitive and proactive. What to do if the tire pressure is insufficient: If no damage is visible on the car's tires, simply inflate them to the normal pressure and reset the tire pressure system. If inspection reveals that the tire has been punctured, drive to a car repair shop promptly to have it patched before reinflating. If the low tire pressure warning appears again some time after inflation, but there is no puncture, it may be due to air leakage caused by a deformed wheel rim. It is recommended to check the wheel rim and replace it if necessary. The working principle of tire pressure monitoring is: It uses pressure sensors installed inside the tires to measure the tire pressure and wireless transmitters to send the pressure information from inside the tire to a central receiver module.
12
2
Share

What is the fuel consumption of the Toyota IZOA?

The following is the fuel consumption data provided by the Ministry of Industry and Information Technology for the IZOA: 1. Urban area: Urban driving cycle fuel consumption is 6.8L/100km. 2. Suburban area: Suburban driving cycle fuel consumption is 5L/100km. 3. Combined: Combined driving cycle fuel consumption is 5.7L/100km. Below is extended information on related content: 1. Fuel consumption generally refers to constant-speed fuel consumption: Constant-speed fuel consumption is the vehicle's fuel consumption per 100 kilometers obtained in the constant-speed driving fuel consumption test specified by national standards for certain types of vehicles. 2. Vehicle types: M1 category, M2 category with a maximum design total mass not exceeding 3.5t, and N1 category compressed natural gas vehicles; M1 category and N1 category vehicles with a maximum design total mass not exceeding 3.5t, tested according to the method specified in GB/T-12545.1-2008 "Test methods for fuel consumption of passenger cars"; M2 category, M3 category, N2 category, and N3 category compressed natural gas vehicles with a maximum design total mass exceeding 3.5t; M2 category, M3 category, and N category vehicles with a maximum total mass greater than or equal to 2t, tested according to the method specified in GB/T-12545.2-2001 "Test methods for fuel consumption of commercial vehicles".
3
0
Share

Where are the reinforcement ribs located on a vehicle?

Reinforcement ribs are mostly located on the roof, engine hood, and doors. Below is a relevant introduction about reinforcement ribs: 1. Definition: When the connection surface of a structural component itself can only bear a limited load, an additional reinforcing plate is added to the common vertical surface between the two connected bodies, commonly known as a reinforcement rib (pronounced as 'JIN' in engineering). 2. Function: To ensure the strength and rigidity of plastic products without increasing the wall thickness of the plastic, reinforcement ribs are set in appropriate parts of the plastic product. This not only prevents deformation of the plastic product but also, in some cases, improves the flow of plastic during the molding process. To enhance the strength and rigidity of plastic products, it is preferable to increase the number of reinforcement ribs rather than their wall thickness. The simplest shape of a reinforcement rib is a rectangular column attached to the surface of the product. However, to meet certain production or structural requirements, the shape and size of the reinforcement ribs may need to be altered.
19
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.