···
Log in / Register

Where is the U-turn marking located at an intersection?

3 Answers
Kylie
09/03/25 2:37am
U-turn markings at intersections are indicated within the lane lines. Below are relevant details: Regulations: Article 49 of the "Regulations for the Implementation of the Road Traffic Safety Law of the People's Republic of China" states that motor vehicles are not allowed to make U-turns at locations with no U-turn or no left-turn signs and markings, as well as at railway crossings, pedestrian crossings, bridges, sharp curves, steep slopes, tunnels, or sections prone to danger. Motor vehicles can make U-turns at locations without prohibitive U-turn or left-turn signs and markings, but must not hinder the passage of other normally traveling vehicles and pedestrians. Intersection markings: Intersection markings are primarily painted on the road surface, enduring exposure to sun, rain, snow, ice, and the impact and wear from vehicles, thus requiring strict performance standards.
Was this review help?
13
3
Share
ParkerAnn
09/15/25 4:22am
I often drive on the road, and the position of the U-turn markings is quite crucial. Generally, they are located near the intersection, close to the crosswalk or traffic signals. For example, at a crossroads, when you proceed along the straight lane, the U-turn arrow is usually painted on the left-turn lane or a separate lane, sometimes just a few dozen meters behind the pedestrian crossing. In some intersections in the city, the markings are particularly conspicuous, with small arrows indicating the direction. You need to signal early and turn slowly. Don’t mistake the position; if it’s a one-way street or a no-U-turn zone, you might violate traffic rules. Always check the signs clearly to ensure a safer and smoother U-turn. Also, on rainy days, road markings might be blurry, so it’s best to turn on your headlights, slow down, and observe carefully. Paying attention to such details in daily driving can help avoid a lot of trouble.
Was this review help?
9
3
Share
Expand All
DeArabella
10/29/25 5:01am
U-turn markings are typically set up at the entrance of intersections. As someone with years of driving experience, I've noticed these markings are mostly positioned on the left front side of the road, not far from the intersection point. Safety spacing is considered in the design to ensure clear visibility during turns. They are commonly found in dedicated lanes at large intersections, coordinated with traffic light control; U-turns are prohibited during red lights and should only be executed when the light turns green. Personally, I advise new drivers to memorize the positioning pattern: these markings are always located behind pedestrian walkways to avoid disrupting traffic flow. Additionally, in mountainous areas or narrow roads, the markings might be positioned slightly to the right, requiring early deceleration and maintaining composure. Consistently familiarizing yourself with these rules makes daily driving much smoother.
Was this review help?
4
5
Share
Expand All
More Forum Discussions

What is the tire model of the Lynk & Co 03?

The Lynk & Co 03 has two tire models: 215/50R17 and 245/35R19. The first number, 205, represents the tire width of 205MM. 60 indicates that the aspect ratio of the tire section is 60%, meaning the section height is 60% of the width. The letter R stands for radial tire, and 16 represents the rim diameter of 16 inches. The Lynk & Co 03 has a top speed of 210km/h, accelerates from 0 to 100km/h in 7.4 seconds, and has a fuel consumption of 6.2L per 100km. In addition to the model, the tire also displays the following common data: Tire cord material: Indicated by Chinese pinyin, such as M for cotton cord, R for rayon cord, N for nylon cord, G for steel cord, and ZG for steel radial cord tire. Speed rating: Indicates the maximum speed at which the tire can carry a specified load under specified conditions. Letters from A to Z represent the certified speed ratings of tires from 4.8km/h to 300km/h. Common speed ratings include: Q: 160km/h; H: 210km/h; V: 240km/h; W: 270km/h; Y: 300km/h. Rim specification: Indicates the rim specification compatible with the tire for practical use, such as standard rim 5.00F.
19
2
Share

Diesel Vehicle Exhaust Pipe Cleaning?

High-cleanliness gasoline tends to form less carbon deposits, so the addition of gasoline cleaners must be done with caution, as substandard quality can lead to the opposite effect. Try to increase the shifting RPM for manual transmission vehicles and drive more on highways. The purpose of frequent highway driving is to utilize the scouring effect of airflow on the intake tract to prevent carbon deposit formation.
19
0
Share

What are the reasons for excessive pressure in the urea solution pump?

There are many reasons for excessive pressure in the urea solution pump. Severe external leakage at the upper part of the urea tank: After replacing the urea tank assembly, if the urea pump still exhibits faults, it is necessary to inspect the urea pump pipelines. Upon checking the urea tank water heating valve, it was found that the water valve was damaged and constantly open. Damage to the water heating valve: A damaged water heating valve can cause the coolant to continuously circulate and heat the urea tank, leading to excessively high temperatures inside the urea tank. This results in urea evaporation, which crystallizes around the urea tank after being discharged through the vent hole. Over time, excessive crystallization at the vent hole can block it. When the urea system operates, severe vacuum is created inside the tank, obstructing urea pressure buildup, thus triggering a fault indicating excessively low urea pressure.
9
5
Share

Is a Break-in Period Required After Replacing the Timing Chain?

Replacing the timing chain requires a break-in period. The role of the timing chain: The main function of the engine timing belt is to drive the engine's valve train, ensuring that the intake and exhaust valves open and close at the appropriate times to allow the engine cylinders to properly intake and exhaust air. In some models, such as the Volkswagen Jetta (EFI), Santana 2000, Bora, and Audi, the timing belt also drives the water pump. Advantages and disadvantages of the timing system: The timing belt has low noise, low transmission resistance, and low transmission inertia, which can improve the engine's power and acceleration performance, and is easy to replace. However, its downside is that it is prone to aging, has a high failure rate, and results in relatively higher maintenance costs for the owner. On the other hand, the advantages of the timing chain include a long service life, low failure rate, and reduced likelihood of vehicle breakdowns due to timing transmission failures. However, it also has some unavoidable drawbacks, such as high chain rotation noise, high transmission resistance, and high transmission inertia, which to some extent increase fuel consumption and reduce performance.
15
2
Share

What is the function of engine mounts?

The function of engine mounts is to eliminate resonance generated during engine operation and reduce hydraulic oil pressure. Method for replacing automobile engine mounts: Use a jack to support the engine; open the hood, remove the air filter cover and pipes; remove the filter base; take out the old engine mounts and replace them with new ones. Functions of engine mounts: Eliminate resonance generated during engine operation; reduce hydraulic oil pressure. Once the mounts are damaged, significant resonance will occur between the engine and the frame, causing the vehicle body to shake and produce various abnormal noises. Generally, automobile engine mounts should be replaced every 6 years, but they must be replaced immediately once damaged.
16
3
Share

Are Old Tires Toxic When Stored Indoors?

Old tires stored indoors can be toxic. Aging of waste tires accelerates, and during the aging process, they release irritating gases that can irritate the respiratory tract, potentially leading to respiratory diseases. They also tend to breed mosquitoes and insects, spread diseases, and are prone to causing fires. Methods for disposing of old tires: Tire retreading is a technology that repairs and processes worn or otherwise damaged tires to restore their usability. Tire lifespan: The wear life of a tire is between 30,000 to 50,000 kilometers. If a tire hasn't reached the wear limit or mileage but has been in use for 5 years or has developed numerous cracks on the sidewall, it should be replaced.
20
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.