Where is the turn signal fuse located in the Hyundai Elantra?

1 Answers
ElizabethLee
07/30/25 7:00am
The turn signal fuse in the Hyundai Elantra is located inside the cover panel below the left side of the driver's seat. Open the cover panel to view it, and the inner side of the fuse box cover records the specific location of each component's fuse. If a fuse is damaged, refer to the repair manual to locate the fuse position before replacing it. Taking the 2020 Hyundai Elantra as an example, it is a compact car with body dimensions of 4610mm in length, 1800mm in width, and 1450mm in height, with a wheelbase of 2700mm. This model is equipped with a 1.4T turbocharged engine, delivering a maximum horsepower of 130PS, a maximum torque of 211Nm, and a maximum power of 95.6kW, paired with a 7-speed dual-clutch transmission.
Was this review help?
4
3
Share
More Forum Discussions

What to Do When the Car Remote Fails to Start the Engine?

Locate the power wire of the anti-theft device and remove its fuse; Follow the thin yellow wire on the anti-theft device to find a power-cut relay; Remove the power-cut relay, then reconnect the original car wires to restore the original wiring.
20
5
Share

How to Sew a Steering Wheel Cover?

First, after starting the stitch, don't rush to sew immediately. Begin with edge tucking by using an insertion tool to push the leather into the gaps. Only start sewing after everything is properly aligned. Regarding the tension, moderate force is sufficient as long as the stitching positions are aligned. At the beginning, there's no need to pull the thread too tight. After sewing a section, you can use a small flat-head screwdriver to tighten the thread before continuing. After completing all stitches and tying the knot, the entire steering wheel cover is sewn. Adjust the lighter flame to high and quickly pass it over the stitched area twice to burn off any frayed edges of the thread.
4
2
Share

How to Repair Wheel Rim Wear?

Carefully sand the worn area of the wheel rim until it becomes smooth, then use metal filler to level the sanded scratches; After filling with the filler, use fine sandpaper to re-sand any uneven areas; Once the secondary sanding is complete, proceed to paint the wheel rim; After the primer is baked dry, apply a layer of clear coat for protection, and then place it back into the baking chamber for high-temperature curing; Once the wheel rim paint is baked dry, use a polishing machine to polish the surface for a more attractive finish.
19
3
Share

How to Open the Trunk from Inside the Regal?

Long press the button on the key other than "Lock" or "Unlock" to open the trunk from inside the car. There is a trunk release button on the door trim panel of the driver's side in the Buick Regal. Press and hold it for more than 3 seconds to open the trunk. Pull the emergency release handle firmly to open the trunk.
4
2
Share

How to Perfectly Fix Water Leakage Above the Car Door?

Thoroughly grind the worn area of the wheel hub until it becomes smooth, then use metal body filler to level the grinding marks on the wheel hub; After using the body filler for leveling, use fine sandpaper to grind any uneven areas again; Once the secondary grinding is completed, you can proceed to paint the wheel hub; After the primer is baked dry, apply another layer of clear coat for protection, and finally place it back into the baking room for high-temperature baking; Once the paint on the wheel hub is baked dry, to make the wheel hub's appearance more attractive, you can polish it using a polishing machine.
18
1
Share

How to Install a Motorcycle Trunk?

Fix the iron plate onto the motorcycle's rear rack using screws. Place the trunk on the installed iron plate and secure it with bolts. Generally, multiple bolts are required to ensure it is firmly fixed. Check the stability and confirm the installation is complete.
7
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.