Where is the trunk drain hole located?

1 Answers
VonGrace
07/30/25 8:15am
Location of the trunk drain hole: The trunk drain hole is located beneath the spare tire. Since the trunk is generally not prone to leaking, the drain hole is not frequently used. Manufacturers often seal the drain hole, which can be unscrewed or punctured when needed. Additional information: 1. Location of door drain holes: Door drain holes are situated at the bottom of the door panel, with at least two drain holes per door. If water accumulates inside the door, it can damage components such as the window regulator and audio system. 2. Location of sunroof drain holes: These are found at the four corners of the sunroof and can be seen when the sunroof is opened. Each drain hole is connected to a hose that directs water to the underside of the car for drainage. 3. Location of the engine compartment drain hole: It is positioned at the air intake for the air conditioning system, below the front windshield.
Was this review help?
1
2
Share
More Forum Discussions

How to Turn Off the Interior Light in a Buick Excelle?

The interior light in a Buick Excelle usually turns off automatically about ten minutes after the door is opened. To manually turn it off, adjust the interior light to the CLOSE position. More information about the Buick Excelle is as follows: 1. The Buick Excelle is the fourth model produced by Buick based on GM's latest global platform, following the new Regal, new LaCrosse, and Enclave. The Buick Excelle is derived from the Opel Astra and built on GM's global Delta-Ⅱ platform. 2. The Buick Excelle is equipped with the latest third-generation small-displacement inline 4-cylinder DVVT-Ecotec engine, paired with a 5-speed manual transmission or a 6-speed automatic manual transmission. It offers three displacement options: 1.6L, 1.8L, and 1.6T.
13
5
Share

What is the DS car emblem?

Cars bearing the DS emblem are brands under the Changan PSA Peugeot Citroën Group. More information about DS is as follows: 1. The brand originated from the 1955 Paris Motor Show and, after years of development, DS models perfectly integrate elements of fashion, luxury, and refinement. 2. DS product series include: DS3, 2018 DS4S, DS4, DS5, DS3 Cabrio, 2018 DS5LS, 2018 DS6, and DS7. 3. As the first model of the new generation products, the DS7 was officially launched at the Beijing Auto Show on April 25, 2018. It is a new SUV model that combines exquisite craftsmanship and cutting-edge automotive technology.
17
1
Share

What Toyota model is the vlos?

vlos is the Toyota Vios. More information about the Vios is as follows: 1. The Vios is equipped with two engines, one is a 1.3L naturally aspirated engine, and the other is a 1.5L naturally aspirated engine. 2. The Vios features a multi-point fuel injection naturally aspirated 2NZ-FE engine, paired with a 5-speed manual or 4-speed automatic transmission, with a maximum power of 63kW at 6000r/min and a maximum torque of 121Nm. 3. The Vios has a body length of 4300mm, width of 1690mm, height of 1490mm, wheelbase of 2550mm, and a minimum ground clearance of 170mm. It has a MacPherson strut front suspension and a torsion beam rear suspension.
11
3
Share

How to Replace the Coolant in a Magotan?

The recommended interval for replacing the coolant in a Magotan is every two years. Method for replacing the coolant: Before performing a complete coolant replacement, conduct a thorough inspection to check for any signs of leakage or cracks in the pipes, with particular attention to the five-way hose. This hose is named for its five connections to various parts of the vehicle, as the coolant flows through it to be distributed to different sections of the car. If there is any sign of coolant leakage in this area, replace the hose or re-secure the connections as necessary. Drain the old coolant, then flush the liquid channels with clean water. Add clean water to the coolant reservoir, then continue adding water until it flows continuously through the engine cooling system. Start the engine and let it idle for 3 to 5 minutes to circulate the water. Initially, the water draining from the reservoir may have a faint pink tint. Continue adding clean water until the outflow is clear. Remember to disconnect the heater hose to drain all water from the heater core. After draining for about an hour, add the new coolant through the radiator hose, which allows the coolant to flow quickly into the radiator. Then, add another container of coolant to the reservoir until it is nearly full. Start the engine and let it run for about 10 minutes. During this time, the coolant level will drop slightly as air is purged from the system. Top up the coolant to the maximum mark "MAXT" on the reservoir.
8
3
Share

How to heat the rearview mirror of the Envision?

Envision rearview mirror heating method is as follows: 1. Step on the car's brake pedal to power on the entire vehicle. 2. Press the vehicle's one-touch start button. 3. The car's dashboard lights up, indicating the entire vehicle is powered on. 4. Press the heating button located next to the vehicle's exterior rearview mirror switch to activate it. More information about the Envision rearview mirror heating is as follows: 1. After activating the exterior rearview mirror heating function, the water mist on the exterior rearview mirror will gradually dissipate. 2. The rearview mirror heating function only works when the ambient temperature is below 15°C, and the heating function should not be kept on continuously. Each use should not exceed 30 minutes, otherwise it may affect the lifespan and clarity of the rearview mirror.
19
1
Share

How to Open the Engine Hood of the Boyue?

The method to open the engine hood of the Boyue is as follows: 1. Pull the engine hood release handle located under the left side of the dashboard on the driver's side inside the car, marked with this symbol. 2. Push the engine hood lock safety hook handle located in the middle of the radiator grille upwards to release it. 3. Slightly lift the engine hood, and under the action of the gas springs on both sides, the engine hood will open to its maximum position. The method to close the engine hood of the Boyue is as follows: 1. Before closing the engine hood, ensure all filler caps are properly closed. Press down on the engine hood, allowing it to fall and lock into place under its own weight. 2. After closing the engine hood, verify that it is fully locked by attempting to lift the front edge of the hood.
2
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.