···
Log in / Register

Where is the trunk drain hole located?

5 Answers
WalterRose
07/28/25 10:24pm

Car trunk drain holes are generally located beneath the spare tire in the trunk. Below are specific methods for dealing with clogged internal door drainage ports: 1. Seal failure: Check whether the door's sealing strip has failed or been damaged, as rainwater can easily enter the door interior, causing the internal waterproof membrane to fail. In severe cases, internal electrical components may also be damaged. Simply replace the waterproof sealing strip. 2. Waterproof membrane damage: Remove the door trim panel to check if the waterproof membrane is damaged. If damaged, rainwater will flow through the gaps onto the door sill, and over time the drainage port will become clogged with dust. The waterproof membrane needs to be replaced. 3. Drainage port clogging: Check if the drainage port is clogged. If clogged, it needs to be cleared. You can use hard objects like iron wire to unclog it, or remove the door to clean the interior thoroughly.

Was this review help?
17
0
Share
VictoriaLee
08/12/25 1:51am

I've been driving sedans for over a decade, and the trunk drain holes are usually located at the four corners of the spare tire well or at low points on the bottom. These are designed to prevent rainwater accumulation, especially during heavy rain or car washes, allowing water to drain away and avoid rusting or wetting items in the trunk. Last time I cleaned it myself, I found the holes clogged with fallen leaves, causing water to pool in the well—it took a while to drain, but thankfully, I dealt with it in time to prevent damage to the spare tire. For daily driving, I recommend regularly lifting the trunk mat to check the drain holes, as they can easily get blocked with mud. A simple poke with a wire can clear them. The exact location may vary slightly between different car models, but they're generally similar. If unsure, refer to the vehicle manual. Developing this habit is crucial—it helps protect the car's overall lifespan and avoids water-related repair issues later on. After all, a small hole can make a big difference in safety.

Was this review help?
18
2
Share
Expand All
VonJesse
10/01/25 3:56am

As someone who regularly maintains their car, the trunk drain holes are usually located at the bottom corners of the spare tire well, designed to guide water out and prevent trunk water accumulation. I've seen many car owners overlook this, leading to clogged holes causing water backflow, soaking or molding the trunk mats, and even rusting the metal frame. Cleaning is simple: lift the mat, locate the small drain slots, and check quarterly. If clogged, use a vacuum or air gun to clear them. Locations vary by car—SUVs might have them inside the bumper corners, but the spare tire area is a common spot. Keeping them clear extends the vehicle's health, prevents odors, and avoids corrosion risks, as water damage is a slow but serious issue.

Was this review help?
14
1
Share
Expand All
ZaneLynn
11/14/25 5:44am

I've driven several cars, and the trunk drain hole is usually located at the bottom or edge of the spare tire well, designed to drain rainwater and prevent water accumulation. This small hole can easily get clogged by leaves or dust. Once blocked, water may overflow into the trunk, dirtying items or damaging wiring. Its position is standardized at the lowest point, but slight variations exist among different car models. Cleaning isn't difficult; regular inspection and unclogging can prevent issues.

Was this review help?
7
1
Share
Expand All
McJosie
01/04/26 7:25am

In automotive repair practice, trunk drain holes are commonly located in the corners of the spare tire compartment, typically designed as small openings to allow water to drain naturally and prevent moisture damage. If these holes become clogged, rainwater can backflow into the trunk, leading to odors or corrosion. The cleaning method involves lifting the trunk mat to directly inspect the channel bottom, then gently clearing the hole opening with a wire. While the location is generally similar, vehicle models may affect details such as the hole orientation. Developing a habit of cleaning them twice a year ensures both peace of mind and safety.

Was this review help?
6
2
Share
Expand All
More Forum Discussions

What Technologies Are Integrated in Intelligent Connected Vehicles?

Intelligent connected vehicles integrate 12 technologies. Here are the details: 1. Introduction: Intelligent vehicles are enhanced with advanced sensors (such as radars and cameras), controllers, and actuators. They utilize onboard environmental perception systems and information terminals to exchange data with vehicles, roads, and pedestrians. This enables the vehicle to intelligently perceive its surroundings, automatically analyze safe and hazardous driving conditions, and reach the destination as intended by the driver, ultimately replacing human decision-making and operation in driving. The initial stage of intelligent vehicles features advanced driver assistance systems (ADAS), and when connected to networks, they become intelligent connected vehicles. 2. Technologies: Environmental perception technology; Wireless communication technology; Intelligent connectivity technology; Onboard network technology; Advanced driver assistance technology; Information fusion technology; Information security and privacy protection technology; Human-machine interface technology; High-precision mapping and positioning technology; Key technologies for heterogeneous network integration; Key technologies for traffic big data processing and analysis; Key technologies for traffic cloud computing and cloud storage.
14
1
Share

How Long After Replacing Glass Can You Apply Tint?

Depending on the quality of the glass adhesive and seasonal factors, it usually takes one to three days for the adhesive to fully cure. During this period when the adhesive is not completely dry, you should not apply window tint, although you can still drive the car. Important notes: 1. Do not wash the car within three days after replacing the windshield. Remove the fixing tape from the windshield only after three days. 2. Try to avoid driving on bumpy roads and refrain from sudden braking or rapid acceleration to prevent the windshield from shifting. 3. Do not insert parking permits or other cards into the gap between the windshield and the dashboard. 4. Avoid highway driving and keep the maximum speed below 80 km/h. 5. Do not apply tint within seven days. If the rear windshield has been replaced, do not open the windows while driving for the first three days to prevent the rear windshield from shifting due to wind pressure. 6. Before applying the tint, the technician should conduct a thorough inspection of the vehicle to ensure there are no cracks in the glass.
8
4
Share

What is the ICCID code of a car?

ICCID is the integrated circuit card identification number of the SIM card built into the car's infotainment system for telematics functions, which needs to be queried at a 4S shop. Below is the relevant introduction: 1. Composition of ICCID: The vehicle ICCID consists of 20 digits, with the encoding format as follows: XXXXXX-0MFSS-YYGXX-XXXXX. The first six digits are the operator code, which is also the unique identification number of the IC card. ICCID is used by some software as a protective measure against piracy. During user registration, a unique identification code is generated based on the computer hardware and software information where the user's software is installed. This is generally referred to as the machine code, also known as the serial number, authentication code, registration code, etc. 2. SN code: SN code is the abbreviation for Serial-Number, sometimes also called SerialNo, which is the product serial number. The product serial number is a concept introduced to verify the "legal identity of the product," used to protect the user's genuine rights and enjoy legal services; a set of genuine products corresponds to only one product serial number. Aliases: machine code, authentication code, registration code, etc. The SN code can be found on the vehicle frame. The SN code is an identification code given by the software developer to the software, similar to a person's ID number, mainly to prevent the software from being pirated by users. Users must know the serial number to use the software.
6
0
Share

How to Determine a Midway Stop in Subject Two Exam?

In the driver's license Subject Two exam, the standard for determining a midway stop is any pause of the vehicle for more than 2 seconds within the test area. Reasons for being judged as a midway stop: 1. Not slightly lifting the clutch when turning the steering wheel to the limit: Many midway stops occur during reversing into a garage, parallel parking, or making a U-turn in a narrow road when the steering wheel is turned to the limit. This happens because once the steering wheel is turned to the limit, the front wheels rotate at a very large angle, increasing driving resistance. 2. Usually controlling the speed very slowly: Students usually follow the coach's instruction to control the clutch steadily and drive slowly, which seems very stable. However, during the exam, if they encounter larger road bumps or undulations, it is very easy to stop. 3. Not pressing the brake firmly when stopping midway during a task: For example, after parking in a parallel parking space, if the first brake press does not hold the brake firmly, and the right foot naturally relaxes during subsequent actions, causing the vehicle to roll back, and then the brake is pressed again to stop, this will also be judged as a midway stop.
12
5
Share

What to Do When the Car Air Conditioner Has an Earthy Smell?

When the car air conditioner emits an earthy smell, the owner can drive the car under the sun, set the air conditioning system to the warm air mode, turn the fan to the maximum setting, and leave it for more than ten minutes with all doors and windows open. If the issue persists, it may be due to a dirty cabin air filter, which needs replacement. If necessary, the air conditioning system can also be cleaned. Here are some extended information: 1. Main reasons for odors in car air conditioners: The primary cause of odors in car air conditioners is the constant dampness in the system. In the air ducts, the interaction of hot and cold air causes water molecules in the air to condense into droplets, creating a moist environment that fosters the growth of bacteria and mold. When outside air enters the car, it first passes through the cabin air filter, where large amounts of dust, insects, leaves, and other impurities are trapped by the multi-layered filter. Over time, these trapped particles can mildew and produce unpleasant smells. 2. Air conditioning usage habits: Sometimes, odors in the air conditioner may be related to the owner's usage habits. It is recommended that owners turn off the air conditioning cooling about five minutes before reaching their destination and switch to natural ventilation. This allows the temperature inside the air conditioning ducts to rise back to normal before parking, preventing the formation of condensation due to temperature differences after parking. Keeping the air conditioning ducts dry helps prevent the growth of mold and fungi.
5
3
Share

Why is the steering wheel of the G-Class so heavy?

The increased heaviness in steering wheel rotation may be largely related to the power steering system. Here is some extended information about steering wheels: 1. Introduction: A wheel-shaped device used to control the direction of cars, ships, aircraft, etc. This new steering wheel design emerged to meet needs, introducing a gear system between the driver and wheels that operates flexibly and effectively isolates intense vibrations from the road. 2. Function: The steering wheel is generally connected to the steering shaft via splines. Its function is to convert the force applied by the driver to the edge of the steering wheel into torque, which is then transmitted to the steering shaft. Using a steering wheel with a larger diameter reduces the hand force required from the driver when turning. The steering intermediate shaft, serving as a connecting component between the steering gear and steering shaft, facilitates the standardization of steering gears, compensates for errors during manufacturing and installation, and allows for more rational installation of the steering gear and steering wheel in the vehicle.
14
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.