···
Log in / Register

Where is the trunk button on the old GL8?

4 Answers
AmeliaMarie
07/29/25 6:00pm
The trunk switch of the Buick GL8 is located in the sunroof control area on the ceiling. The trunk capacity of the Buick GL8 is 475-1605L. Relevant information is as follows: 1. Dimensions: The Buick GL8 is a popular joint-venture MPV model with a body length, width, and height of 5256/1878/1776mm respectively, and a wheelbase of 3088mm. 2. Powertrain: The Buick GL8 is a classic top-tier MPV under the Buick brand, equipped with a 3.0L VVT V6 engine, delivering a maximum horsepower of 178 and a top speed of 168km/h.
Was this review help?
17
2
Share
VanEmmanuel
08/14/25 10:02am
On older GL8 models, the trunk button is typically located on the inner door panel on the driver's side, right next to the window control buttons. You can easily feel it by bending down slightly. Some variants may place it on the center console near the gearshift or central locking buttons, which is also easy to locate. If you can't find it, don’t forget to check the key fob—there’s a small button with a trunk icon. Having driven this model for years, I can confirm its ergonomic placement allows one-touch access, ideal for loading luggage. Pro tip: If the button fails, there’s a manual release under the trunk lid—just pry it open with your key. Generally, the door panel is the most common location; if not found there, inspect other spots and keep the car clean to prevent button jams.
Was this review help?
8
2
Share
Expand All
Lauren
10/14/25 3:34am
Having driven many older GL8 models, the trunk button is mostly fixed on the control panel inside the driver's left door. Just press it, and you'll hear the unlocking sound. Occasionally, some versions have it moved near the steering wheel in the center console area. Those with remote keys also integrate the trunk function—just press the button on the key. If you really can't find it, don't panic. There's a hidden mechanical switch on the trunk lid; just twist it open with the key. As an experienced owner, I believe the placement is for safety to avoid accidental presses and to prevent dust. Regularly cleaning dust around the button is important, or it may cause poor contact. Also, aging wiring in older vehicles can make the button unresponsive, so early maintenance is key.
Was this review help?
1
2
Share
Expand All
VonConnor
11/27/25 4:29am
For the trunk button of the older GL8 models, the common location is on the control panel inside the driver's door, which integrates the unlocking function. Depending on the year or configuration, the button may be relocated near the center console or operated directly via the key remote. If you can't find it, check the owner's manual or try the manual trunk release. Position variations depend on the automaker's design philosophy, emphasizing simplicity and prevention of accidental operation. I recommend starting with the door panel to avoid unnecessary hassle.
Was this review help?
17
1
Share
Expand All
More Forum Discussions

What Amount of Current is Considered a Leakage in Cars?

For ordinary cars, a current exceeding 40mA is considered a leakage, while for high-end cars, it's over 80mA. Below is a detailed introduction about car current leakage: Reasons for normal leakage: Some electrical devices must remain powered to maintain data memory functions. These devices mainly include computer control units and anti-theft sensors, which require continuous power supply to ensure round-the-clock monitoring capabilities. All these factors contribute to the inherent current leakage in cars. Reasons for abnormal leakage: Short circuits or oxidation shedding of the battery plates leading to self-discharge and power loss, as well as electronic components and circuits grounding causing leakage and battery depletion, are the primary causes of abnormal leakage.
6
1
Share

Can You Add Pure Water When Antifreeze Is Low?

You cannot add pure water when antifreeze is low. You must use the same brand of antifreeze. Different brands of antifreeze may have varying production formulas, and mixing them could lead to chemical reactions between additives, rendering them ineffective. Method for replacing antifreeze: Before completely replacing the antifreeze, conduct a thorough inspection to check for any signs of leakage or cracks in the pipes, with a focus on the five-way hose. The five-way hose is named for its five connections to different parts of the vehicle. Antifreeze flows through this hose and is distributed to various parts of the car to function. If there is any leakage of antifreeze in this section, replace the hose or resecure the connections as needed. Drain the old antifreeze, then flush the fluid channels with clean water. Add clean water to the antifreeze reservoir, then continue filling the reservoir to ensure water continuously circulates through the engine cooling system. Start the engine and let it idle for 3 to 5 minutes to allow the water to circulate. The initial water draining from the reservoir may appear slightly pinkish. Continue adding clean water until the drained water runs clear. Remember to disconnect the heater hose to drain all water from the heater system. Approximately one hour after draining, add the new antifreeze through the radiator hose to allow it to flow quickly into the radiator. Then, add another bottle of antifreeze to the reservoir until it is nearly full. Start the engine and let it run for about 10 minutes. During this time, the coolant level may drop as air is purged from the system. Top up the antifreeze until it reaches the "MAXT" mark on the reservoir.
15
4
Share

What is the correct way to step on the clutch, brake, and accelerator?

The correct way to step on the clutch, brake, and accelerator: 1. The left foot controls the clutch pedal, while the right foot controls the accelerator and brake pedals; 2. The left foot must press the clutch when shifting gears; 3. When not in use, the left foot should rest on the car's chassis, not on the pedals; 4. In emergencies, stomp on the brake firmly to ensure the vehicle stops in the shortest possible time, minimizing braking distance and preventing accidents; 5. When overtaking, press the accelerator firmly—driving side by side is most dangerous, so overtake as quickly as possible; 6. Avoid stomping on the brake pedal unnecessarily, both for passenger comfort and to prevent rear-end collisions.
2
0
Share

What Are the Hazards of Drowsy Driving?

The hazards of drowsy driving include decreased judgment, slower reaction times, and increased operational errors, which can easily lead to safety accidents. Below is a detailed introduction about drowsy driving: Identification Criteria: Driving a motor vehicle continuously for more than 4 hours without stopping for a break or with a break of less than 20 minutes is considered drowsy driving. Methods to Prevent Drowsy Driving: Control speed: High-speed driving can easily make drivers nervous. Driving slightly below the normal speed, without affecting traffic, can reduce mental stress and fatigue. At the same time, minimizing overtaking and emergency braking during driving can also alleviate fatigue and reduce safety hazards.
3
0
Share

What tire models can be used for 14-inch rims?

14-inch rims can use tires with sizes 175/70/R14, 175/65/R14, and 185/65/R14. The matching relationship between rims and tires is as follows: It is necessary to know the J value of the rim: Once the rim is selected, attention must be paid to the tread width when choosing tires, and the corresponding rim J value must be known. For example, a 5.5J rim can accommodate tire widths from 175 to 195mm, with the optimal width being 185mm. Tire size must be adjusted after rim upgrade: When the diameter of the rim increases, the sidewall of the matching tire must become shorter. The diameter of the modified wheel should be the same as that of the original vehicle wheel; otherwise, the speedometer will show deviations after modification, and the wheels may interfere with the body during movement.
13
3
Share

Can mineral engine oil still be used after seven months?

Mineral engine oil cannot be used after seven months because it deteriorates rapidly after being stored for more than six months, significantly reducing its lubrication effectiveness. Below are detailed explanations: Usage cycles for different types of engine oil: Mineral engine oil needs to be replaced every 5,000 kilometers or six months. Semi-synthetic engine oil has a usage cycle of about 7,500 kilometers or eight months. Fully synthetic engine oil has a usage cycle of about 10,000 kilometers or one year. Hazards of not changing engine oil for a long time: If a car does not change its engine oil for an extended period, the oil will become ineffective and deteriorate. Instead of providing protection, it will increase wear and damage to engine components. Additionally, its cooling effect diminishes, leading to the accumulation of a large amount of carbon deposits and sludge.
19
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.