Where is the transmission fluid for the Volkswagen Lamando?

1 Answers
AbelLee
07/25/25 2:50pm
Volkswagen Lamando transmission fluid filler port is located next to the right-side axle, specifically under the transmission where there is an 8mm hex screw port serving as the drain port. Approximately 2L can be added. Below are the steps for cleaning transmission components: 1. First, lift the car and remove the transmission cover with a screwdriver. 2. Carefully remove the oil pan, ensuring to support it by hand. 3. Remove the transmission fluid filter, at which point the solenoid valves controlling gear shifts will be visible. 4. Take off the oil pan gasket and clean surrounding stains; carburetor cleaner can be sprayed. 5. Wipe all cleaned transmission fluid filtration components with cotton cloth and reinstall them one by one.
Was this review help?
19
1
Share
More Forum Discussions

How to Install Dynamic Trajectory Lines if the Original Vehicle Doesn't Have Them?

If you want to install dynamic reversing trajectory lines, you need to obtain the steering angle data of the front wheels, so a steering angle sensor must be installed. Generally, dynamic reversing trajectory lines are only available on some luxury cars, and compact cars or family vehicles usually don't come with this feature.
9
4
Share

How to Practice Subject 3?

1 Press the clutch, 2 Shift to first gear, 3 Turn signal, 4 Horn, 5 Release the handbrake, 6 Accelerate. The RPM should not exceed 2000, and slowly release the clutch to start. The clutch should only be used when starting, shifting up, shifting down, or stopping, and the pressing time should not exceed 5 seconds. Never press the clutch during normal driving. After the voice prompt for the roadside parking test item is issued, do not forget to turn on the turn signal first. After changing lanes, wait for the car body to straighten before turning off the turn signal. When shifting gears, pause at the neutral position before pushing the gear. All gears should be pushed in a straight line, not diagonally, and the hand posture should be correct.
17
3
Share

How to Obtain an Electronic Driver's License?

Download the "Traffic Management 12123" APP and register after installation. Click the registration button and follow the prompts for individual user registration. After completing the registration, the login interface will appear. Enter your ID number and password to log in. Click on the driver's license to bind your driver's license information. Click on the driver's license to view your information, such as the validity period of the driver's license.
19
4
Share

How to Prevent the Car Body from Crossing the Line When Reversing into the Garage?

Turning the steering wheel too early. When straightening the wheels, you need to do it a bit earlier than usual. Not turning the steering wheel to the full lock position in time. You should turn the wheels back after passing the usual point for returning to the straight position. The success rate this time is 99%. When reversing, turn the steering wheel to the right full lock position earlier, then straighten the wheels.
20
0
Share

How to Replace the Windshield Seal?

Prepare a small flat-head screwdriver and 401 special adhesive. First, handle the unglued seal to ensure the unglued area is smooth and free of wrinkles, otherwise the sealing effect cannot be guaranteed. Apply the 401 special adhesive to the tip of the small flat-head screwdriver. Do not apply the adhesive directly onto the seal to prevent leakage and contamination of the car body. After applying the adhesive, press the seal with one hand and slowly spread the adhesive from the screwdriver onto the unglued area with the other hand, moving from top to bottom. Gradually press the seal from top to bottom until all unglued parts are reattached. Finally, press back and forth a few times to ensure the seal is firmly adhered.
16
4
Share

How to Adjust the Time on a 2021 Audi Q3?

Turn on the ignition switch. Press and hold the protruding button in the middle of the instrument panel for 3 seconds. Once the hour digits start flashing, you can press the button up or down to adjust. After setting the hour, wait for 2 seconds until the minute digits start flashing, then continue pressing the button up or down to adjust. Once both the hour and minute are set, the time on the instrument panel will flash simultaneously. At this point, simply wait for 5 seconds to complete the process.
14
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.