Where is the Transfer Case Located in a 4WD Vehicle?

1 Answers
LolaAnn
07/25/25 3:33pm
The transfer case in a 4WD vehicle is located behind the transmission. It is a device that distributes the engine's power, directing it either to the rear axle or simultaneously to both the front and rear axles. The transfer case is a crucial transmission component in 4WD vehicles. Below is some related information about the transfer case: 1. After the engine's power passes through the transmission, it is directly connected to the rear axle via the driveshaft. The transfer case extends an additional output from the transmission and uses a silent chain to transfer power to the front axle's output shaft. 2. It enhances the vehicle's off-road capability and offers high reliability. Switching to two-wheel drive mode on smooth roads can help reduce fuel consumption.
Was this review help?
12
1
Share
More Forum Discussions

Can the locking beep sound of Changan CS35 be set?

Changan CS35's locking beep sound cannot be set. Here is an introduction to relevant knowledge about Changan CS35: 1. Features of Changan CS35: The Changan CS35 car has a stylish and bold appearance, making it eye-catching on the road; the overall handling is good, with accurate steering; the price is reasonable, offering high cost performance. 2. Power of Changan CS35: The CS35 is equipped with a new generation BlueCore efficient H-series 1.6L engine, with a maximum output power of 125 horsepower and a maximum torque of 160N·m.
3
4
Share

Where is the handbrake in Geely cars?

Geely's handbrake is located on the left side of the gear shift. Here is more information about the handbrake: 1. Function: The car handbrake is used to keep the vehicle stationary when pulled up during parking, preventing the car from rolling downhill. When driving, pulling up the handbrake during a turn can create a drifting effect. However, the handbrake should not be used as a brake in emergency situations. 2. Concept: The parking brake, also known as the handbrake or the parking gear in automatic transmissions, locks the drive shaft or rear wheels. The parking brake provides much less force compared to the service brake and is only meant to prevent the car from rolling on slopes. 3. Types: There are different types of parking brakes, such as mechanical systems operated by hand or foot. Additionally, high-end vehicles are increasingly adopting electronically controlled parking systems, commonly known as electronic handbrakes.
17
2
Share

Difference Between Scratches and Cracks on Car Glass?

The difference between scratches and cracks on car glass is that scratches exhibit obvious surface damage that can be felt by touch, while cracks appear as irregular lines or spider-web-like patterns radiating from the center. Below are methods for repairing car glass scratches: 1. DIY Repair: (1) Purchase specialized products designed for glass scratch repair. (2) Use a wool polishing pad to apply ferric oxide for repair. 2. Professional Repair: For larger scratches, entrust the repair to professional technicians at vehicle repair shops or auto beauty shops.
17
1
Share

What is the difference between dual CVTC and ECVT?

The differences between dual CVTC and ECVT are as follows: 1. Dual CVTC: Dual CVTC is a variable valve timing system, which is a technology used in automotive piston engines. The variable valve timing system consists of solenoid valves and variable camshaft phase adjusters. By adjusting the camshaft phase of the engine, the intake volume can change with the engine speed, thereby achieving optimal combustion efficiency and improving fuel economy. The variable valve timing system can not only change the opening and closing times of the intake and exhaust valves but also enhance power output to some extent. Its principle involves using hydraulic action to alter the angle between the camshaft synchronous timing belt pulley and the end of the camshaft, thus changing the valve timing angle. 2. ECVT: ECVT can only be used in motor-driven or hybrid vehicles and is not applicable to gasoline engines. It adjusts speed through the motor, features an all-gear structure, can withstand greater torque, and offers higher efficiency and faster speed.
10
1
Share

What is the CRDI car?

Honda CRider is actually the Honda Lingpai. The Honda Lingpai is a new strategic mid-size sedan under GAC Honda, specifically designed by GAC Honda to meet the comprehensive needs of post-80s consumers as a mainstream compact car. Here are the detailed specifications: 1. Powertrain: It is equipped with a brand-new 1.0t inline three-cylinder engine with the code name P10A3. This engine delivers a maximum power of 122 horsepower and a peak torque of 173 Nm. The transmission system is paired with either a six-speed manual or a CVT continuously variable transmission. 2. Features: In the mid-to-high trim levels of the new Lingpai, a 7-inch multimedia display is provided, integrating functions such as Bluetooth telephony, audio system, and vehicle information.
10
0
Share

What are the reasons for the abnormal noise in the rear brake of the UY125?

The reasons for the abnormal noise in the rear brake of the UY125 are as follows: 1. Break-in period for new vehicles: New vehicles or recently replaced brake discs and pads will have a break-in period, during which some abnormal noises are unavoidable. These noises typically disappear after driving a few hundred kilometers. 2. Normal activation of the ABS system: During emergency braking, the brake pedal may produce a continuous "thudding" sound, sometimes accompanied by a pulsating sensation. This indicates that the ABS system is activated, which is normal. In such cases, firmly press the brake pedal all the way down, but this applies only to vehicles equipped with an ABS system. 3. Metal hard spots on the brake pads: Brake pads may contain small metal particles, which can produce sharp, screeching noises when lightly braking. This issue can be resolved by forcefully applying the brakes several times, removing and regrinding the brake pads, or replacing them with higher-quality ones. 4. Severe wear on the brake disc: Wear on the brake disc can create deep grooves around its circumference. Friction between the brake pads and the edges of these grooves can cause abnormal noises. If the grooves are not too deep, grinding the edges of the brake pads to avoid contact with the groove edges may solve the problem. If the grooves are very deep, replacing the brake disc is necessary. Generally, it is recommended to replace the brake disc every two brake pad replacements.
12
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.