Where is the tire pressure reset button for Wuling Rongguang V?

1 Answers
StJoshua
07/30/25 12:14am
The tire pressure reset button for Wuling Rongguang V is located below the dashboard. Here are some related introductions about car tire pressure: 1. Tire pressure reset button: It is operated by the buttons on the multifunction steering wheel, storing the tire pressure status through the "tire pressure" option in the multifunction menu; there is also a tire pressure reset switch on the side of the gear lever. With the ignition switch on, press and hold this switch button until a beep is heard, indicating the reset is complete. 2. During normal driving: If a tire leaks causing low tire pressure, the diameter of that wheel will decrease. After driving a certain distance, the speed sensor of that wheel detects that the speed difference between it and other wheels reaches a certain value, triggering the tire pressure warning light. When the tire pressure warning light comes on, it is recommended to reduce speed, turn on hazard lights, find a safe place to stop, get out to check which tire is leaking, and decide whether to continue driving or change to a spare tire based on the actual situation. 3. Tire pressure warning: It is a very dangerous signal that requires high attention because tires are the primary condition for vehicle safety. The tire pressure monitoring system uses the principle of gravity balance. If the tire pressure is balanced, it will display as normal. If a tire is punctured and leaks, breaking the balance of gravity, the monitoring system will start to alarm.
Was this review help?
7
3
Share
More Forum Discussions

What to Do About Oil Leakage from the Engine Valve Cover Gasket?

Methods for handling oil leakage from the engine valve cover: It is recommended to directly replace the valve cover assembly and use high-boiling-point antifreeze. Below is an introduction to related content: Oil leakage from the engine valve cover can affect the engine's lubrication, and in severe cases during hot weather, it may even lead to vehicle self-ignition. If oil leakage is detected from the engine valve cover, it is essential to promptly inspect and repair it. Causes of oil leakage from the engine valve cover: 1. Uneven force distribution during assembly. If the screws are not tightened evenly, the pressure they exert will vary. Excessive pressure can cause the engine valve cover to deform, leading to oil leakage. In such cases, the valve cover must be repaired. 2. Aging of the valve cover gasket. When a car has been owned for too many years or has been driven for an excessive mileage, the aging of the valve cover gasket is a normal occurrence. In this situation, simply replacing the valve cover gasket and sealing ring will suffice.
2
0
Share

Can the Subject 2 Driving Test Be Taken in a Different Location?

After passing the Subject 1 driving test, you can take the Subject 2 test in a different location. The public security authorities have introduced 10 new measures for the reform of "delegating power, improving regulation, and upgrading services" in traffic management, including "cross-regional handling" for 5 types of services such as driving tests and "convenient and fast handling" for 5 services including vehicle mortgage registration. These measures have been implemented since June 1, 2019. More details are as follows: 1. In terms of "cross-regional handling," first, small vehicle driving licenses can be obtained nationwide. Applicants can apply for a small vehicle driving license anywhere in the country with their resident ID card, without needing to submit proof of residence registration. 2. Secondly, the subject tests can be taken in different locations. If an applicant who has passed some subjects of the small vehicle driving test changes their residence due to work, study, or life reasons, they can apply to change the test location and continue the remaining subjects, reducing the burden of traveling back and forth for tests.
12
3
Share

How to Handle a Lost Driver's License?

If you lose your driver's license, there is no need to report it as lost. You simply need to promptly visit the vehicle management office at the place of issuance to apply for a replacement. Below is relevant information regarding the replacement of a driver's license: 1. Required Materials: (1) Original and photocopy of the identity proof of the motor vehicle driver. (2) Original driver's license (if the license is damaged) / Written statement of loss of the driver's license (if the license is lost). (3) Original receipt of the provincial motor vehicle driver's license digital photo collection. 2. Important Notes: (1) After the replacement process is successfully completed, you cannot drive a motor vehicle with the original license before receiving the new one. If the replacement process is initiated but the new license is not issued on the same day due to time constraints, you must not drive during this "gap period" until the new license is obtained. Driving without the new license during this time will be considered as driving without a license. (2) Once a new license is issued, the original driver's license becomes invalid. If you lose your driver's license and obtain a replacement, even if you later find the original license, it will still be considered invalid (as you have already "declared" it lost). In such cases, the new license is the valid one.
13
2
Share

Is Replacing the Cylinder Head Assembly Considered a Major Overhaul?

Replacing the cylinder head assembly is considered a major overhaul. Typically, the causes of cylinder head damage in automobiles include: alloy cylinder heads exposed to high temperatures; uneven tightening torque of cylinder head bolts; extensive burning of the cylinder gasket; and other external forces causing cylinder head damage. The problems caused by a damaged cylinder head are as follows: 1. While driving, you may often feel the engine lacks power and has difficulty accelerating. There may be air leakage sounds at the joint between the cylinder head and the cylinder block or in localized areas; 2. After starting the engine, one or two cylinders may not function, producing a 'bang, bang' sound. The radiator may continuously lose water, with bubbles appearing at the radiator filler neck, or oil droplets may be visible on the surface of the coolant; 3. When checking the engine oil by pulling out the dipstick, the oil may appear milky white. Water droplets may continuously flow out of the exhaust pipe; 4. The engine may overheat. When the cylinder gasket is severely damaged, not only does the engine power drop significantly, but sometimes it may even fail to start. Generally, when such faults occur, replacing the cylinder head is sufficient, and the engine oil should also be changed simultaneously.
8
3
Share

How to Start a Car with Tiptronic Transmission?

Correct starting method for a tiptronic transmission car: The vehicle can only be started in P or N gear. The N gear start is used when the vehicle is to move forward immediately after starting. You can first turn on the power, press the brake, shift the gear to N, then ignite the engine, and subsequently shift to D gear to move forward directly. This avoids the transmission experiencing a reverse impact when passing through R gear after ignition in P gear. More details are as follows: 1. Parking: After the car is in the parking position, press the brake, shift the gear lever to N gear, pull up the handbrake, release the foot brake, and then turn off the engine. Finally, press the brake again and push the gear lever into P gear. Of course, this is also a meticulous protection for the transmission. 2. Temporary parking: When temporarily parking (such as waiting for a red light), whether to use N gear or D gear is not wrong, it just depends on personal habits. Temporarily stopping and pressing the brake in D gear does not harm the car because the torque converter in the transmission is equipped with a reaction wheel with a one-way clutch, which amplifies the torque from the engine crankshaft. It does not rotate at engine idle speed and only comes into play when the engine speed increases.
14
1
Share

What to Do If the Lamination Film of the Driver's License Peels Off?

If the lamination film of the driver's license peels off, you can go to the vehicle management office for a replacement. Below is relevant information about driver's license damage: 1. Relevant regulations: Article 60 of the "Regulations on the Application and Use of Motor Vehicle Driver's Licenses" stipulates that under any of the following circumstances, the motor vehicle driver shall apply for a replacement at the vehicle management office of the issuing authority or outside the issuing area within 30 days: (1) Within the jurisdiction of the vehicle management office, the motor vehicle driver's information recorded on the driver's license changes. (2) The motor vehicle driver's license is damaged and cannot be recognized. 2. Relevant materials: When applying, you should fill out the "Motor Vehicle Driver's License Application Form" and submit the following documents and proofs: (1) The identity proof of the motor vehicle driver. (2) The motor vehicle driver's license. (3) A physical condition certificate issued by a medical institution at or above the county level or the regimental level of the military. If applying for a driver's license for a small automatic passenger vehicle for the disabled, a physical condition certificate issued by a specialized medical institution designated by the provincial health authority must be submitted.
7
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.