···
Log in / Register

Where is the tire pressure reset button for the Geely Emgrand?

4 Answers
EstherMarie
07/29/25 8:16pm
Geely Emgrand's tire pressure reset button is located on the instrument panel display. Adjust the tire pressure to the normal value, then press and hold the tire pressure reset button for 3 seconds to perform the tire pressure reset. The tire pressure light indicates that the pressure of a certain tire is not within the standard range, and the tire pressure needs to be checked. Taking the Emgrand GS new 1.4T manual Yalife as an example: 1. Dimensions: It is a compact SUV with a length, width, and height of 4440mm, 1833mm, and 1573mm respectively, and a wheelbase of 2700mm. 2. Power: Equipped with a 1.4T turbocharged engine, paired with a 6-speed manual transmission.
Was this review help?
3
4
Share
JanelleRose
08/14/25 4:42pm
When driving my Geely Emgrand, I often encounter the tire warning light coming on, which requires resetting the tire pressure system. The button is usually located below the left side of the steering wheel, near the door, marked with a TPMS or tire icon. The operation is simple: first ensure all tire pressures are normal, start the engine, then locate the button in the driver's seat, press and hold it for a few seconds until the warning light on the dashboard goes off. When I first bought the car, it took me some time to figure it out, but after getting familiar with it, it became easy. The key is to check tire conditions frequently, as weather changes can affect tire pressure. Timely resetting can prevent false alarms and avoid potential safety hazards on the road. I recommend new car owners try the procedure when they have time and make it a habit, as safety always comes first.
Was this review help?
2
3
Share
Expand All
DelGabriela
10/16/25 3:25am
When driving my friend's Geely Emgrand, I found the tire pressure reset quite convenient, with the button usually hidden in the corner on the left side of the steering wheel or under the instrument panel. Here's how to do it: After starting the car, locate that button and hold it until the light goes off. Personally, I think the car is thoughtfully designed, and the reset process is simple without affecting driving. Just a heads-up: Check tire pressure regularly—don't wait for the warning light to act. If the light stays on, it might indicate a leak or sensor issue, so get it checked at a shop ASAP. This saves repair hassles, extends tire life, and ensures reliability when it counts.
Was this review help?
10
0
Share
Expand All
ZoeFitz
11/29/25 4:12am
Resetting the tire pressure on a Geely Emgrand is quite straightforward. There's a small button located on the left side or beneath the steering wheel. As someone who works on cars myself, I've done this multiple times: simply start the vehicle and hold the button for a few seconds until the dashboard warning disappears. The whole process is quick, taking just a minute or two. Remember to maintain stable tire pressure—neither too high nor too low—to avoid frequent alerts. After resetting, it's good to drive around a bit to let the system recalibrate.
Was this review help?
5
4
Share
Expand All
More Forum Discussions

What is the method to reset the maintenance light on an older GL8?

Turn the key to position I while holding down the mileage reset button. Continue holding the mileage reset button for approximately 10 seconds. You will hear two beeps, indicating a successful reset.
7
4
Share

What to Do When All Vehicle Lights Suddenly Go Out During Night Driving?

When all vehicle lights suddenly go out during night driving, you should turn on the hazard warning flashers, gradually slow down, and pull over to the side of the road. Headlights must be turned on at night. When overtaking at night, it is advisable to increase the distance between vehicles appropriately. When driving at speeds above 30 km/h at night, high beams should be used.
18
0
Share

How to Remove Oil Film from Car by Yourself?

First, clean the car thoroughly, then apply detergent, scrub vigorously on the glass, and finally rinse with clean water or wipe with a damp towel. Toothpaste contains abrasives, and baking soda also has oil-removing properties.
10
3
Share

How to Determine if the Fuel Metering Unit is Damaged?

It will cut off the fuel injection to the engine, and continued use may cause the engine to malfunction. It may result in stalling or black smoke emissions. In the electronic fuel injection system, the fuel metering unit is an indispensable component.
5
2
Share

What are the correct steps for starting a three-wheeled motorcycle?

When starting, first pull the clutch and shift into first gear, then slowly release the clutch. When you feel the motorcycle has the intention to move forward, continue to increase the throttle and smoothly release the clutch. Do not release the clutch too quickly, so you can start smoothly.
13
3
Share

How to License a Motorcycle Without the Invoice?

If documents such as the invoice are lost, you can obtain a certificate from your local neighborhood committee or village office, then proceed with the licensing process along with the certificate of conformity. A motorcycle cannot be licensed without an invoice. You can first apply for a duplicate invoice. The licensing process includes verification: after purchasing the motorcycle, bring the invoice issued by the dealer to complete the verification procedure.
18
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.