Where is the tire pressure monitoring button on the new Lavida?

What Causes Unstable Idle Speed After a Major Overhaul of the Ford Kuga?

This situation is most commonly caused by excessive carbon buildup inside the throttle body. The idle speed control valve fails to regulate the idle properly. Take the vehicle to a repair shop and have a technician clean the throttle body and idle speed control valve. Below are the reasons for low idle speed: Throttle Body Carbon Buildup: As the vehicle ages, the intake passages can become clogged. Carbon deposits or oil inside the throttle body can lead to unstable idle speed or even low idle. Spark Plug Carbon Buildup: Over time, carbon can also accumulate on the spark plugs. Severe carbon buildup can weaken the spark on some cylinders, affecting vehicle performance and causing low idle speed. Clogged Fuel Injectors: When the fuel injectors become clogged, the fuel supply pressure and atomization deteriorate, resulting in unstable or low idle speed.

18

4

Share

How to Wire a 6-Wire LED Tail Light?

Cut the original running light wire, connect a resistor in series, and extend a wire from the running light side, defined as Wire 1. Cut the controller's low-level brake wire, connect a diode in series, paying attention to the diode polarity—positive to the controller side and negative to the brake lever wire side. Identify the power wire entering the controller, usually a thin red wire, which is the 48V power controlled by the ignition lock. Typically, there are only two red wires entering the controller. First, use a multimeter in resistance mode to measure any two pins. The two pins showing resistance are the control coil pins, arbitrarily defined as Control 1 and Control 2. Connect Control 1, Trigger 1, and Wire 3 together. Connect Wire 1 to Wire 2, and Wire 2 to Control 2. Cover all resistors, diodes, and connection points with heat shrink tubing and secure them tightly.

10

4

Share

What are the differences between Mercedes-Maybach and Mercedes-Benz S-Class?

The differences between Mercedes-Maybach and Mercedes-Benz S-Class are: 1. Different body dimensions: The Mercedes-Maybach has a length, width, and height of 5466mm, 1899mm, and 1500mm respectively, with a wheelbase of 3365mm; the Mercedes-Benz S-Class has a length, width, and height of 5283mm, 1905mm, and 1500mm respectively, with a wheelbase of 2945mm. 2. Different driving methods: The Mercedes-Maybach is front-engine, rear-wheel drive; the Mercedes-Benz S-Class is full-time four-wheel drive. 3. Different power options: The Mercedes-Maybach offers three power models, equipped with a 3.0T V6 twin-turbocharged engine, a 4.0T V8 twin-turbocharged engine, and a 6.0T V12 twin-turbocharged engine respectively; the Mercedes-Benz S-Class offers two power models, equipped with a 2.0T turbocharged engine and a 3.0T turbocharged engine respectively.

20

3

Share

What procedures are required for vehicle name change and transfer?

The procedures required for vehicle name change and transfer are as follows: 1. Owner's ID card: Present the owner's ID card to prove the legal citizen identity of the owner. 2. Vehicle registration certificate: The seller needs to present the vehicle registration certificate to prove ownership of the vehicle. If the seller refuses to present the vehicle registration certificate for various reasons during the transaction, the buyer must be cautious, as the vehicle may be an illegally obtained stolen car. There are two ways for direct relatives to transfer a motor vehicle: 1. Transaction method: Still need to go to the motor vehicle trading market to complete the relevant procedures. The processing point can be the vehicle management office under the ID card of the owner or the vehicle management office under the ID card of the transferor, but the transferor does not need to go in person. 2. Gift method: You can go to a notary office to complete a gift notarization, and use the gift statement and notarized certificate to complete the transfer registration. However, the notarization fee is charged as a percentage of the value of the gifted vehicle, which is generally higher than the transaction method fee.

19

5

Share

What Happens If Diesel Vehicles Are Filled with 92 Gasoline?

Added gasoline diesel engine can still start, but will be weak and work rough, large vibration, slow speed, loud noise, cannot be used normally, and may even cause damage to the diesel engine. The following are the differences between diesel engines and gasoline engines: Ignition Method: Diesel engines and gasoline engines have different fuels, ignition methods, and working principles. Diesel and gasoline are two completely different fuels. Diesel has a lower auto-ignition temperature, around 220°C, and is more viscous and less volatile. Gasoline has a higher auto-ignition temperature, around 415°C~530°C, and is less viscous and more volatile. The working principles of diesel engines and gasoline engines are also different. Diesel engines use compression ignition, while gasoline engines use spark ignition. Different Compression Ratios: The compression ratios are different. Diesel engines have much higher compression ratios than gasoline engines. The compression ratio of diesel engines is generally between 16-22, and can reach as high as 26, while the compression ratio of gasoline engines is smaller, generally between 8-11, and can reach up to 14.

1

3

Share

What Are the Reasons for a Diesel Vehicle Having Fuel but Failing to Start?

Insufficient battery charge preventing the starter motor from operating, blocked fuel tank pipelines, fuel transfer pump failure to deliver fuel, clogged intake pipes, excessive dust accumulation or moisture in the air filter, severe wear of the engine cylinder liner, and carbon buildup on piston rings can all cause a diesel vehicle to fail to start. Solutions for a diesel vehicle having fuel but failing to start: Check the battery terminals: Start troubleshooting from the source by inspecting the battery terminals. Clean the terminals thoroughly and tighten the terminal screws. Bleed air from the engine: First, locate the hand primer pump. The installation position of the hand primer pump varies by engine brand—some are installed near the diesel pump, while others have an additional electric fuel pump, eliminating the need for manual air bleeding. Most excavators currently on the market have the hand primer pump installed above the fuel-water separator. Loosen the air bleed bolt next to the hand primer pump, manually pump the primer until only diesel flows out of the bleed bolt, and then tighten the bleed bolt. Drain water from the fuel-water separator: The fuel-water separator typically has a red float with a density between diesel and water, causing it to float on the water surface while remaining at the bottom of the diesel. When the float is observed in the middle position, promptly open the drain bolt at the bottom of the fuel-water separator to remove the water.

5

Share

Where is the tire pressure monitoring button on the new Lavida?

What Causes Unstable Idle Speed After a Major Overhaul of the Ford Kuga?

How to Wire a 6-Wire LED Tail Light?

What are the differences between Mercedes-Maybach and Mercedes-Benz S-Class?

What procedures are required for vehicle name change and transfer?

What Happens If Diesel Vehicles Are Filled with 92 Gasoline?

What Are the Reasons for a Diesel Vehicle Having Fuel but Failing to Start?

What are the differences between the Mercedes-Benz S320 and S350?

What Causes the Sudden Increase in Idle Speed When Braking?

Do I need to take a card when using ETC on the highway?

How Many Days Does It Take to Practice Reverse Parking?