Where is the tire pressure monitor located on the Volkswagen New Lavida?

1 Answers
SanAshley
07/29/25 9:55pm
The tire pressure monitor on the Volkswagen New Lavida is located at the bottom of the combination switch on the left side of the steering wheel. Tire pressure refers to the air pressure inside the tire. Common tire pressure monitoring methods: Direct tire pressure monitoring: The direct tire pressure monitoring device uses pressure sensors installed in each tire to directly measure the tire's air pressure. It uses a wireless transmitter to send the pressure information from inside the tire to a central receiver module, which then displays the tire pressure data for each tire. The system automatically alerts when the tire pressure is too low or there is a leak. Indirect tire pressure monitoring: When the air pressure in a tire decreases, the vehicle's weight causes the rolling radius of that wheel to become smaller, resulting in a faster rotation speed compared to other wheels. By comparing the differences in rotation speed between tires, the system monitors the tire pressure. The indirect tire pressure warning system essentially relies on calculating the rolling radius of the tires to monitor the air pressure. Introduction to the Tire Pressure Monitoring System (TPMS): It combines the advantages of both systems mentioned above. Direct sensors are installed in two diagonally opposite tires, and a 4-wheel indirect system is also equipped. Compared to using only a direct system, this hybrid system can reduce costs and overcome the limitation of the indirect system, which cannot detect when multiple tires simultaneously have low pressure. However, it still cannot provide real-time data of the actual pressure in all four tires like the direct system.
Was this review help?
8
1
Share
More Forum Discussions

How to Repair a Faulty Igniter?

Igniter damage does not require repair; it should be replaced directly. An igniter refers to a device capable of providing sufficient energy in an instant to ignite pulverized coal, oil (gas) fuel, and stabilize the flame. The car igniter is a system used to start the vehicle's engine. The causes of igniter failure are as follows: 1. Poor contact: When using the igniter, the car may experience sudden stalling without obvious patterns. Replacing the platinum contacts can eliminate the issue. This is usually due to loose connections or damaged wiring grounding in the igniter circuit. 2. Replacing the igniter: After prolonged driving, the car may exhibit unstable operation or stalling, which returns to normal after cooling down. This phenomenon does not occur with platinum contacts, indicating that the igniter chip may have high-speed misfiring issues, necessitating the replacement of the igniter.
7
5
Share

What to Do When the Car Stalls on a Steep Slope?

Solutions for stalling on a steep slope are introduced as follows: 1. Slowly release the clutch and brake: When starting on a slope, first ensure the clutch and brake are fully depressed. Slowly release the clutch until the car body shakes significantly. Keep the clutch pedal steady with your left foot and slowly release the brake with your right foot. Once the car starts moving, fully release the brake and gently press the accelerator to complete the slope start. 2. Use the handbrake: You can also use the handbrake to start. When parking on a slope, pull up the handbrake. During the start, control the handbrake with your right hand and the clutch with your left foot. When the clutch reaches the semi-engaged state, keep the clutch steady, slightly press the accelerator, and release the handbrake to complete the slope start. The key to this method is mastering the semi-engaged state. 3. Use inertia: If the road before the slope is flat and traffic permits, you can increase the speed to use the car's inertia to complete the slope climb.
2
1
Share

Will There Be Problems If a New Car Is Left Unused for 6 Months?

Leaving a new car unused for six months can have some impact on the battery, various fluids, rubber components, paintwork, and related drainage holes. Recommendations for long-term vehicle storage 1. Preparation before parking: The exterior and interior of the car should be thoroughly cleaned before storage. Applying wax or a coating can help protect the paint from corrosion. If possible, store the car in a garage. If parking outdoors, at least use a car cover to shield it from sun, rain, and debris like fallen leaves that could damage the paint. 2. Brake discs: For vehicles parked for extended periods, it's best not to engage the parking brake too tightly. The brake system can easily react chemically with moisture and oxygen in the air when left idle. Combined with rainwater erosion, the brake discs and pads may rust to varying degrees, potentially sticking together and affecting braking performance. Upon restarting, this could lead to wheel lock-up. 3. Tires: To prevent tire deformation, inflate them to a higher pressure than usual—around 2.8 bar is typical practice at dealerships. Additionally, choose a flat surface for parking to minimize tire damage. Parking on uneven surfaces for long periods can cause tire deformation. 4. Battery: Even when unused, car batteries self-discharge. It's advisable to start the engine every one to two weeks to prevent complete battery discharge and avoid internal engine rust. 5. Fluid systems: In long-unused vehicles, engine oil, brake fluid, coolant, and electrolyte can oxidize and deteriorate. While lubrication effects quickly resume upon restarting, this can cause significant wear initially. Therefore, periodically start the car and ideally take it for a short drive to reach normal operating temperature. Before regular use, replace the engine oil and other fluids and perform appropriate maintenance.
6
5
Share

What is the SVR car?

SVR belongs to high-performance vehicles. SV stands for Special-Vehicle-Operations, which translates to Special Vehicle Manufacturer, while the red R represents performance. More extended information is as follows: 1. Configuration: Without compromising fuel economy, the sport-tuned ZF 8-speed automatic transmission 8HP70 and the four-wheel-drive system have been optimized to enhance the driving experience under various weather and road conditions. The Range Rover Sport SVR is equipped with a full-time four-wheel-drive system and a two-speed transfer case, enabling a 50:50 torque distribution between the front and rear axles. The upgraded air suspension can automatically adjust between two chassis heights, which is highly beneficial for navigating complex terrains. 2. 39% reduction in weight: As a luxury SUV, the Range Rover Sport SVR has undergone bold improvements in this aspect. The seats are more robust with a sportier design. Compared to its predecessor, the Range Rover Sport SVR has achieved a 39% reduction in weight while ensuring better body rigidity and handling.
3
5
Share

How many cylinders does the Mercedes-Benz C260 engine have?

The Mercedes-Benz C260 is equipped with a 4-cylinder turbocharged engine. Here is some additional information: 1. Vehicle Design: The all-new Mercedes-Benz C-Class coupe features a stylish and elegant exterior, with scratch-resistant paint being a major highlight. The interior design follows the overall layout of the sedan version, incorporating a new steering wheel, a 12.3-inch digital instrument cluster, and a 10.25-inch central control touchscreen. The interior space, especially the rear seats, is relatively compact, but the trunk is spacious. 2. Engine: The Mercedes-Benz C-Class is powered by 1.5T high and low-output turbocharged engines, with maximum power outputs of 156 horsepower and 184 horsepower, and peak torques of 250 Nm and 280 Nm, respectively. These engines utilize direct fuel injection technology, with the low-output version achieving maximum torque at 1500-4000 rpm and the high-output version at 3000-4000 rpm. There is also a 2.0T turbocharged engine with a maximum power output of 258 horsepower and peak torque of 370 Nm. This engine also features direct fuel injection technology, with maximum torque achieved at 1800-4000 rpm, and uses an aluminum alloy cylinder head and block.
3
1
Share

What are the reasons for the Wuling Hongguang Mini's air conditioning not being cool enough?

The reasons for the Wuling Hongguang Mini's air conditioning not being cool enough are as follows: 1. Clogged air filter: This issue is often overlooked by many new drivers. Simply replacing the air filter can resolve it. 2. Dirty condenser leading to poor heat dissipation: The condenser is prone to accumulating dust and small insects. If not cleaned for a long time, the condenser's heat dissipation will be poor, significantly reducing the air conditioning's cooling effect. The dirt on the condenser can be cleaned by rinsing with water, but be careful not to use too high water pressure as the condenser is relatively fragile. 3. Cooling fan not working: A non-functioning cooling fan greatly affects the condenser's heat dissipation. It should be repaired or replaced promptly. 4. Refrigerant pressure too high or too low: Refrigerant, also known as coolant, is the cooling agent inside the air conditioning system. There is a natural loss of refrigerant in the air conditioning system over time. If the refrigerant pressure is too low, the cooling effect will deteriorate. Conversely, if the refrigerant pressure is too high, the air conditioning may cool intermittently. Therefore, the refrigerant pressure must be adjusted to the standard range; neither too low nor too high is ideal. 5. Refrigerant leakage: This situation is more troublesome. Specialized equipment is needed to locate the leak point inch by inch. Common leak points include the air conditioning pipes and the evaporator, which may require replacement of related components.
20
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.