Where is the Tiguan's cabin air filter located?

What is the spark plug model for Mercedes-Benz GLA?

The spark plug model for Mercedes-Benz GLA is NGK Iridium Platinum Spark Plug 90654 (sparkplug), commonly known as a spark plug. Its function is to discharge the pulsed high voltage sent by the high-voltage wire (spark plug wire), break down the air between the two electrodes of the spark plug, and generate an electric spark to ignite the mixed gas in the cylinder. Below is relevant information about spark plugs: 1. The insulator of a spark plug must have good mechanical properties, high voltage resistance, high-temperature impact resistance, and chemical corrosion resistance. Ordinary spark plugs are mostly made of alumina-based ceramics. 2. The size of spark plugs is standardized worldwide and can be used universally in any car. However, due to differences in gasoline engine types, spark plugs are divided into two basic types: cold type and hot type. 3. Cold type and hot type are relative terms, reflecting the thermal characteristics of the spark plug. A spark plug must maintain an appropriate temperature to function properly, and it must be free of carbon deposits to operate normally.

15

4

Share

What does brake assist EBA mean?

EBA stands for Emergency Brake Assist. Here is an introduction about EBA: 1. Under normal circumstances, most drivers apply only a small amount of force when they begin braking, then increase or adjust the braking force applied to the brake pedal based on the situation. If a much larger braking force must be applied suddenly, or if the driver reacts too slowly, this method can hinder them from applying the maximum braking force in time. 2. EBA interprets the braking behavior by the rate at which the driver presses the brake pedal. If it detects a panic-induced increase in braking pressure on the brake pedal, EBA will activate full braking force within milliseconds, which is much faster than most drivers can move their feet. 3. EBA can significantly shorten the emergency braking distance and help prevent rear-end collisions in stop-and-go traffic. The EBA system monitors the movement of the brake pedal based on time. Once it detects a sharp increase in the speed of pressing the brake pedal and the driver continues to press the pedal forcefully, it releases the stored 180-bar hydraulic pressure to apply the maximum braking force. 4. Once the driver releases the brake pedal, the EBA system switches to standby mode. By applying the maximum braking force earlier, the Emergency Brake Assist can significantly reduce the braking distance.

18

2

Share

What engine does the Avalon use?

The Avalon's engine is produced by Tianjin FAW Toyota Engine Co., Ltd., and is a domestically manufactured engine. The 2.0L version of the Avalon's engine has the model number M20A, with a maximum power of 131kw, maximum horsepower of 178 HP, and peak torque of 210Nm. The 2.5L version has the model number A25A, with a maximum power of 154kw, maximum horsepower of 209 Ps, and peak torque of 250Nm. For daily maintenance of the Avalon's engine, the following methods can be used: Use lubricating oil of the appropriate quality grade. For gasoline engines, select SD--SF grade gasoline engine oil based on the additional equipment of the intake and exhaust systems and usage conditions. For diesel engines, choose CB--CD grade diesel engine oil based on mechanical load, with the selection standard not lower than the manufacturer's specified requirements. Regularly change the oil and filter. The quality of any grade of lubricating oil will change during use. After a certain mileage, performance deteriorates, leading to various engine problems. To avoid malfunctions, change the oil regularly according to usage conditions and maintain an appropriate oil level. When oil passes through the fine pores of the filter, solid particles and viscous substances in the oil accumulate in the filter. If the filter becomes clogged and oil cannot pass through, the filter may burst or the safety valve may open, allowing oil to bypass the filter and carry contaminants back to the lubrication areas, accelerating engine wear and increasing internal contamination. Regularly clean the crankcase. During engine operation, high-pressure unburned gases, acids, moisture, sulfur, and nitrogen oxides from the combustion chamber enter the crankcase through the gap between the piston rings and cylinder walls, mixing with metal particles from component wear to form sludge. Small amounts remain suspended in the oil, while larger amounts precipitate, clogging filters and oil passages, making engine lubrication difficult and causing wear. Regularly use a radiator cleaner to clean the radiator. Removing rust and scale not only ensures the engine operates properly but also extends the overall lifespan of the radiator and engine.

2

Share

What is the mileage for the first maintenance of the Lynk & Co 03 car?

The first maintenance mileage for the Lynk & Co 03 car is 10,000 kilometers. Unlike most other family cars, the first maintenance cycle for this model is 10,000 kilometers, which is relatively rare among family vehicles. The majority of family sedans have their first maintenance cycle at either 3,000 kilometers or 5,000 kilometers. Below is more information about the Lynk & Co 03 warranty: 1. The main content of the first maintenance for the Lynk & Co 03 includes changing the engine oil and oil filter, along with a comprehensive inspection. 2. The three-guarantee validity period for the Lynk & Co 03 is 2 years or 50,000 kilometers, and the warranty period is unlimited in terms of years and mileage.

15

3

Share

Does the Peugeot 3008 Have Independent Suspension?

The Peugeot 3008 features a MacPherson strut independent suspension at the front and a torsion beam non-independent suspension at the rear. Below is a related introduction to the Peugeot 3008: 1. Body dimensions are 4435*1840*1652mm with a wheelbase of 2613mm. 2. It offers the following two engines: 1. A 2.0L naturally aspirated engine with a maximum power of 147 horsepower (108kW) at 6000rpm and a maximum torque of 200N·m at 4000rpm. 2. A 1.6T turbocharged engine with a maximum power of 167 horsepower (123kW) at 6000rpm and a maximum torque of 245N·m between 1400-4000rpm.

16

3

Share

What are the reasons for the 8th generation Accord's air conditioning not being cool?

8th generation Accord air conditioning not cooling generally has the following reasons: 1. The compressor capacitor is damaged or faulty, causing the compressor not to work. 2. Refrigerant leakage in the air conditioning system: manifests as both the indoor and outdoor units working, the compressor also working, but with no effect. 3. The remote control is faulty or the air conditioning receiver is faulty: manifests as the air conditioning not responding when turned on, or working intermittently. 4. The resistance value of the room temperature sensor changes, causing the outdoor unit not to work. 5. Air conditioning power supply issues. 6. Four-way valve or compressor high and low pressure gas mixing, the air conditioning works but has no effect. 7. Fault in the indoor or outdoor unit control board causing the air conditioning not to cool: manifests as no response when turned on or erratic operation of the air conditioning. 8. Damage to the indoor or outdoor fan, with the outdoor fan damage manifesting as excessive exhaust temperature or high pressure protection, and the indoor fan damage manifesting as frost formation on the indoor unit, the outdoor unit continuously working, and moisture entering the indoor unit.

17

5

Share

Where is the Tiguan's cabin air filter located?

What is the spark plug model for Mercedes-Benz GLA?

What does brake assist EBA mean?

What engine does the Avalon use?

What is the mileage for the first maintenance of the Lynk & Co 03 car?

Does the Peugeot 3008 Have Independent Suspension?

What are the reasons for the 8th generation Accord's air conditioning not being cool?

What are the differences between the Mercedes-Benz C260 and C260L?

Is Ford an American or German car?

What is the difference between spoked wheels and solid wheels?

How to reset the tire pressure on Audi Q3?