···
Log in / Register

Where is the three-way catalytic converter installed in a car?

1 Answers
LeWalker
09/01/25 3:45am
The three-way catalytic converter is located at the front end of the engine exhaust pipe, between the front and rear oxygen sensors. The three-way catalytic converter is the most important external purification device installed in the automobile exhaust system. It can convert harmful gases such as CO, HC, and NOx emitted by automobile exhaust into harmless carbon dioxide, water, and nitrogen through oxidation and reduction reactions. Symptoms of a faulty three-way catalytic converter: Increased fuel consumption: When the three-way catalytic converter begins to clog, it affects the normal operation of the oxygen sensor, making it impossible to precisely control fuel injection, intake, and ignition, thereby increasing fuel consumption. Reduced vehicle power: When high-pressure exhaust is required, clogging will lead to poor exhaust, which affects the intake volume, resulting in decreased engine power and poor acceleration. Three-way catalytic converter fault light illuminates: When the engine's related sensors detect abnormal exhaust emissions, they will provide a signal to the electronic control unit, ultimately alerting the owner through the fault light.
Was this review help?
13
2
Share
More Forum Discussions

Where is the cabin air filter located in a 2011 Teana?

11-year-old Teana cabin air filter is located behind the glove compartment in the front passenger side of the vehicle cabin. Below is the replacement method for the Teana cabin air filter: 1. To access the Nissan Teana's cabin air filter, you need to enter the front passenger side. First open the front passenger door, enter the cabin and prepare to open the glove compartment - the cabin air filter is located behind the glove compartment. 2. The glove compartment needs to be removed for replacement. After removing the glove compartment, locate the cabin air filter housing, remove the filter cover, and pull out the old cabin air filter. Observe the shape of the old filter, mold the new filter into the same shape, then install the new cabin air filter and replace the filter cover.
4
5
Share

How to Turn Off ECO Mode in a Car?

Switch the square button below the dashboard brightness adjustment on the left side of the dashboard to the ECO ON interface, then press and hold to turn off the ECO mode. Principle of ECO: ECO primarily involves a comprehensive judgment and analysis of factors affecting fuel consumption during vehicle movement, such as automatic transmission gear position, engine speed, vehicle speed, braking, and transmission oil temperature. In a few cases, it is unnecessary to activate ECO: 1. When the car is driving at high speed (up to 100km/h), even if ECO is turned on, the vehicle's computer will prioritize speed, and the ECO mode will automatically deactivate. 2. When a large torque output is required, such as climbing a hill, the engine computer will prioritize ensuring and providing sufficient power to drive the vehicle, and the ECO mode will automatically deactivate.
11
3
Share

How to Remove and Install the Blower of Venucia T70?

Here are the steps for removing and installing the blower of Venucia T70: 1. Locate the exact position of the blower, which is behind the glove compartment on the passenger side; 2. First remove the rear storage box of the cup holder. To remove the cup holder, first take off the slender panel, then rotate counterclockwise to remove the blower. Below is more information about the blower: 1. Composition: The blower mainly consists of a motor, air filter, blower body, air chamber, base (also serving as an oil tank), and oil drip nozzle. 2. Working principle: The blower operates by the eccentric rotation of the rotor inside the cylinder, causing the volume between the blades in the rotor slots to change, thereby sucking in, compressing, and expelling air. 3. Sliding vane blower: During operation, the pressure difference of the blower automatically delivers lubrication to the oil drip nozzle, which drips into the cylinder to reduce friction and noise, while also preventing gas backflow in the cylinder.
8
5
Share

Where is the trunk button on the Changan CS35?

Changan CS35 is equipped with an electric trunk switch. The electric rear door switch is located on the dashboard, and there is also an opening button on the trunk inside the car. The smart key also has a trunk button. Here is some information about the Changan CS35: The Changan CS35 is equipped with a new generation BlueCore efficient H-series 1.6L engine, featuring three major advantages: "power, cleanliness, and quietness." Among them, "cleanliness" refers to the Changan CS35's use of technologies such as DVVT, DOHC, low friction, lightweight, and Bosch STT, which result in lower fuel consumption and stronger power during operation, allowing every drop of fuel to achieve maximum efficiency.
15
4
Share

What is Assisted Range?

Assisted range refers to a vehicle's ability to continuously travel in assisted mode, which is the average distance that can be covered on a full tank of fuel. The specific details are as follows: 1. The same hull or aircraft can have significantly different endurance capabilities at different speeds. For automobiles, it refers to the continuous travel distance, and the instrument panel displays how many kilometers the vehicle can still travel—this figure is the range. 2. Assisted range indicates the vehicle's continuous travel capability. For example, a 50L tank that allows the car to travel 600km represents the range. Many modern vehicles are equipped with this feature, which can be viewed on the instrument panel. This function enables the driver to monitor the remaining fuel level and the estimated distance the vehicle can still travel, as well as understand the vehicle's fuel consumption. The assisted range typically displays a set of numbers on the vehicle's dashboard.
19
3
Share

How to Deal with Scratches on a White Car?

Treatment methods are as follows: 1. First, carefully wipe the scratch and the surrounding paint with a chamois cloth, then apply everyday toothpaste to the scratched area. Ensure the application is even, and reapply after rain or car washing. Note that applying toothpaste to the scratch only provides temporary protection and prevents rusting. 2. Start by sanding with very fine-grit sandpaper, sanding in straight lines to remove rust spots and toothpaste, then apply a thin, even layer of primer. After the primer dries, sand it smooth. 3. Carefully apply two layers of masking tape along both sides of the scratch, exposing only the scratch. It's best to apply multiple layers of tape. Be meticulous when applying to fully enclose the scratch, ensuring optimal touch-up results. 4. If the car came with a small can of original paint, apply it evenly over the primer with care. 5. If original paint is unavailable, use a touch-up pen. Shake the pen thoroughly before use and apply multiple coats, waiting 5-10 minutes between each. Once completely dry, sand smooth with sandpaper.
14
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.