Where is the Sylphy engine produced?

1 Answers
JessicaAnn
07/29/25 7:58pm
Sylphy engines are produced domestically. The Sylphy is equipped with an HR16 naturally aspirated engine, featuring multi-point fuel injection, with a maximum power output of 90kw at 6000rpm and a maximum torque of 155 Nm. It comes with a 5-speed manual transmission and adopts a front-engine, front-wheel-drive layout. The Sylphy is a five-seater sedan under Dongfeng Nissan, with a body length of 4641mm, width of 1815mm, height of 1447mm, wheelbase of 2712mm, front track of 1475mm, and rear track of 1480mm.
Was this review help?
13
1
Share
More Forum Discussions

Can I temporarily use the old license plate when replacing one?

You can temporarily use the old license plate when replacing one. Here are the relevant details: 1. Procedure: The vehicle owner must personally visit the local vehicle management office in their district/county to complete the license plate replacement procedure. In addition to the vehicle's registration certificate and the owner's ID card, the motor vehicle registration certificate must be brought if it has been processed. For company vehicles, the organization code certificate is also required. 2. Additional information: The owner first needs to fill out a license plate replacement application form at the vehicle management office. For company vehicles, the form must be stamped with the company seal before submission. After 30 working days, you can collect the new license plate from the vehicle management office. The new license plate will have the same number as your original one, and your vehicle registration certificate can still be used.
13
0
Share

Can You Press the Brake Before the Clutch?

No. Specific details are as follows: In driving school: Instructors require students to press the clutch before the brake. The reason instructors ask students to do this is that when the car is idling, braking without pressing the clutch can easily cause the car to stall. Therefore, to ensure students pass the test, instructors require them to press the clutch before the brake. Clutch: It is a device that connects or disconnects the power transmission between the engine and the gearbox. Incorrect operation: Pressing the clutch before the brake or pressing both simultaneously is a common mistake made by many beginners. At low speeds, using these methods can avoid jitter or stalling caused by gear shifting. However, at high speeds, doing so can wear out the clutch and damage the clutch plate. In severe cases, it may even lead to brake failure, resulting in tragic accidents.
3
0
Share

What to Do If the Daytime Running Lights Stay On?

The solution to daytime running lights staying on is: With the engine off and power disconnected, turn on the left turn signal, maintain the left turn signal position and pull the light lever inward, then turn the key to power on. After about 3 seconds, a "ding" sound can be heard, and the daytime running lights will turn off. Daytime running lights are designed to signal the presence of the vehicle to the front during the day and are installed on both sides of the front end. When the car engine starts, the daytime running lights automatically turn on and gradually increase in brightness to attract the attention of other motor vehicles, non-motor vehicles, and pedestrians on the road. When night falls and the driver manually turns on the low beam headlights, the daytime running lights automatically turn off.
13
4
Share

Can a Car Pass the Annual Inspection with Reverse Lights Not Working?

If the reverse lights are not working, the car cannot pass the annual inspection. During the inspection, the vehicle body and its accessories must be complete and functional to pass. Therefore, non-functional reverse lights will result in a failed inspection. The lighting inspection mainly consists of two parts: 1. Visual inspection, where inspectors visually check the vehicle's exterior for unauthorized modifications and ensure all lights are operational; 2. Instrument testing on the inspection line. The annual vehicle inspection refers to the yearly examination of vehicles that have obtained official license plates and registration certificates, conducted according to the safety technical conditions for motor vehicle operation. Its purpose is to check the main technical conditions of the vehicle, encourage regular maintenance, and ensure the vehicle remains in good condition, thereby guaranteeing driving safety.
12
4
Share

Will I get points deducted for crossing a single solid yellow line?

Changing lanes by crossing a single solid yellow line is considered a traffic violation. Crossing any solid line will result in a 3-point penalty. Crossing solid line violations: One of the most common violations committed by new drivers, often due to carelessness. In fact, besides crossing white solid lines, there are many other traffic markings that prohibit vehicles from crossing lines. Additional information: Function of white solid lines: To separate lanes in the same direction, usually painted before traffic lights at intersections. Many drivers are caught on camera for crossing this type of marking. Function of single solid yellow lines: To prohibit vehicles from crossing or driving over the line in both directions. Single solid yellow lines are generally painted on roads with only one lane in a single direction or one motor vehicle lane and one non-motor vehicle lane, or on sections where overtaking is prohibited due to other hazards.
4
0
Share

What are the model numbers of Audi engines?

Audi engines mainly come in two model numbers: the 1.4T engine is model EA211, while the 1.8T and 2.0T engines are model EA888. Below are detailed introductions: Features of the EA211 engine: The EA211 engine, developed based on the Volkswagen MQB platform, utilizes an all-aluminum cylinder block and incorporates an ACT active cylinder management system, which can shut down two cylinders under certain conditions, leaving the other two cylinders to operate. Features of the EA888 engine: This engine combines technologies such as direct fuel injection, turbocharging, and variable valve timing, serving as the main power unit for mid-to-high-end models under the Volkswagen Group.
18
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.