Where is the sunroof drainage located?

1 Answers
McIsabella
07/29/25 6:59pm
The sunroof drainage is located inside the vehicle's A-pillars and C-pillars. The functions of a sunroof are: 1. Effectively ventilate the interior air and increase the intake of fresh air; 2. Broaden the field of vision and meet the shooting requirements for mobile photography. The car sunroof is installed on the roof, and the method to open it is: rotate the sunroof switch button. Car sunroofs are divided into: built-in sunroofs, pop-up sunroofs, and panoramic sunroofs. The maintenance methods are: 1. Clean the sunroof drainage channel in a timely manner and regularly wipe the sunroof guide rails with a damp sponge; 2. Apply silicone oil to the sunroof sealing strip after washing the car to effectively prevent aging of the rubber strip and extend the service life of the sealing strip.
Was this review help?
2
2
Share
More Forum Discussions

Can the Sylphy handle long-distance trips?

Sylphy is capable of long-distance travel. The specific reasons are as follows: 1. The Nissan Sylphy Classic exhibits good stability during long-distance journeys. 2. The steering wheel of the Sylphy is relatively light, reducing driver fatigue during extended driving. 3. Particularly notable is the excellent comfort of its seats. To ensure safety during long trips, it is essential to perform the following necessary checks before embarking: inspect vehicle lights, tire pressure, acceleration, braking, clutch pedal, seat belts, steering wheel performance, brake fluid level, coolant level, engine oil level, and windshield washer fluid level.
15
4
Share

What are the reasons for the car heater not getting hot?

Car heater not getting hot may be due to damage in the engine's cooling system or the water pump impeller. Damage in the engine's cooling system: If the engine's cooling system is affected by airlock, it can cause the car's cooling circulation system to malfunction, leading to the heater not getting hot. If the heater's small radiator has a hot inlet pipe but a cold outlet pipe, it indicates a blockage in the small radiator that needs replacement. Damage to the water pump impeller: If the vehicle's water pump impeller is damaged or slipping, it reduces the water flow through the radiator, resulting in the heater not getting hot. A new water pump impeller needs to be replaced.
7
4
Share

What is the purpose of the intake camshaft solenoid valve?

The purpose of the intake camshaft solenoid valve is to control the opening and closing of the valves. The working principle of the intake camshaft solenoid valve is as follows: during braking, the valve closes the engine exhaust pipe, forcing the engine crankshaft to rotate. During the compression and exhaust strokes, air is compressed in the cylinder, increasing the piston's exhaust resistance, thereby achieving the goal of reducing vehicle speed through the transmission system. Possible damages to the intake camshaft solenoid valve include: 1. Poor lubrication; 2. Insufficient oil supply pressure from the oil pump; 3. Blockage of the lubrication oil passage, preventing oil from reaching the camshaft; 4. Inability of lubrication oil to enter the camshaft clearance, leading to abnormal wear of the camshaft.
9
0
Share

Why does the idle speed gauge needle slightly fluctuate?

Idle speed gauge needle slight fluctuation is caused by fuel system issues or electrical circuit problems. Fuel system issues: Fuel system problems are generally caused by fuel line blockages, resulting in poor fuel supply, manifested as engine shaking, unstable idle speed, and stalling while driving; additionally, fuel pump failure can also cause engine vibration. The solution is to diagnose fuel pump issues by disconnecting fuel lines and checking fuel flow rate and volume. Electrical circuit problems: Check if the ignition timing is accurate, as abnormal ignition is usually a timing issue; additionally, malfunctioning distributors can also cause engine vibration. Solutions include checking if spark plugs are worn, whether their gaps are uniform, and if the gaps have changed.
9
0
Share

Can You Apply Film to a Rear Windshield with Heating Wires?

Rear windshields with heating wires can have film applied. Functions of the film: Applying film to the rear windshield can block ultraviolet rays, reduce heat transmission, prevent injuries from shattered glass, and minimize glare. Additionally, the one-way visibility feature of solar films helps protect personal privacy. Precautions when applying film: While it is possible to both apply and remove film from rear windshields, damage to the heating wires usually occurs due to either poor film quality or unprofessional installation. The heating wires are coated with an enamel layer, and improper removal techniques can damage this enamel even if the wires themselves are not broken.
5
5
Share

What does oilservice mean?

oilservice means that the car needs maintenance. The maintenance content includes: 1. Check whether the tire pressure is normal and whether the tires have uneven wear, bulges, or damage; 2. Inspect the car chassis, including brake pads, brake discs, connecting rods, ball joints, and CV joints for scratches; 3. Replace engine oil, oil filter, clean the air filter, and check whether the generator belt and wiper blades are damaged; 4. Check whether the levels of various fluids are normal; 5. Inspect all switches and lights in the car to ensure they are working properly. Maintenance precautions are: 1. Make an appointment in advance; 2. Record any faults or questions encountered while driving and inform the staff during maintenance registration.
1
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.