Where is the steering wheel heating switch on the Touareg?

1 Answers
StRuth
07/29/25 9:03am
The steering wheel heating button and rear windshield heating share the same button on the center console, and the operation is very simple. After turning on the vehicle's power, just press the steering wheel heating button. The heated area is not the entire steering wheel, but the left and right grip points of the circular steering wheel, commonly referred to as the 3 and 9 o'clock positions. The steering wheel heating function is particularly useful in northern regions, making the steering wheel warm during cold seasons and preventing the driver from feeling uncomfortable due to the cold. This feature is generally found in higher-end vehicles and is controlled via a heating button on the steering wheel. The Touareg is an SUV produced by Volkswagen in Germany, with body dimensions of 4795mm in length, 1940mm in width, and 1709mm in height.
Was this review help?
12
0
Share
More Forum Discussions

What are the causes of idle shaking in a new car?

New car idle shaking may be caused by the following reasons: 1. Engine carbon deposits: Excessive carbon deposits inside the engine can cause idle shaking after a cold start. Due to excessive carbon deposits, a large amount of gas sprayed by the engine will be absorbed by the carbon deposits, resulting in an overly lean air-fuel mixture, which makes starting difficult and causes shaking. 2. Ignition system issues: Poor performance of the ignition system or suboptimal spark plug firing can lead to idle shaking in a new car. 3. Unstable fuel pressure: Abnormal fuel pump supply pressure or incorrect readings and poor performance of the intake pressure sensor can cause body shaking. It is recommended to check the fuel supply pressure and intake pressure sensor at a 4S shop to ensure they are functioning properly.
20
1
Share

What Causes Car Body Shaking During Idling?

Car body shaking during idling is mainly caused by severe engine carbon deposits, ignition system issues, unstable oil pressure, aging engine components, etc. Below is a detailed introduction to car shaking during idling: 1. Ignition System Failure: Every time the ignition system is used, the spark plugs will wear out. Long-term use will lead to severe motor wear, causing the spark plug gap to increase, making it difficult to generate an arc, which increases the misfire rate. Inconsistent power output will cause the car to shake during idling. 2. Unstable Oil Pressure: The most common issue in the fuel supply system usually occurs with the fuel injectors. Excessive carbon deposits on the fuel injectors affect the fuel injection volume. When the fuel injection volume is too high or too low, it can easily cause the oil pressure to be too high or too low, leading to shaking during idling.
6
1
Share

What are the length, width, and height of the T-Roc?

The length, width, and height of the T-Roc are 4318mm, 1819mm, and 1582mm respectively. Here is some additional information: 1. The T-Roc features a MacPherson strut front suspension and a multi-link rear suspension, with tire specifications of 215/55R17. It adopts a front-engine, front-wheel-drive layout. 2. The T-Roc has a very sporty appearance. It adopts the latest family design language, with a horizontal grille at the front that connects to the headlights on both sides. The chrome trim below connects to the bottom of the headlights, and the raised lines on the hood give it a powerful look. The lower grille features a large trapezoidal honeycomb pattern, with polygonal LED daytime running lights embedded on both sides for better recognition, and the bumper is accented with silver trim at the bottom.
17
3
Share

What kind of glue can be used to bond a car bumper?

Epoxy resin adhesive can be used to bond a car bumper. Knowledge about epoxy resin adhesive: 1. Characteristics: Epoxy resin adhesive is known for its high strength, ability to withstand heavy loads, and resistance to aging, fatigue, and corrosion, ensuring stable performance throughout its expected lifespan. 2. Uses: (1) It can be used for fiberglass bonding, such as the interior of boat hulls and bus bodies; (2) It can replace woodworking strong glue for bonding woodwork; (3) It can also be used to bond wood that has suffered from corrosion; (4) It is used to reinforce standard parts to prevent cracking; (5) It is used in jewelry making to achieve excellent results.
19
4
Share

How to Choose a Sedan?

When choosing a sedan, you should consider two key indicators: the engine and the transmission. Here is a partial introduction to the indicators for selecting a sedan: 1. Engine: Displacement options include 1.0L, 1.5L, and 1.6L. Generally, a larger displacement means stronger power, higher fuel consumption, and a higher car price. The intake methods can be naturally aspirated or turbocharged. Naturally aspirated engines have more mature technology and, at the same displacement, offer less power than turbocharged engines, but their maintenance costs are cheaper than turbocharged engines. 2. Transmission: Manual transmissions typically come in 5-speed and 6-speed options. Their advantages are low cost and mature technology. Automatic transmissions include 4AT, 5AT, 6AT, 8AT, and even 9AT and 10AT. Their advantage is mature technology.
18
5
Share

What is the optimal position for rearview mirrors?

The optimal position for rearview mirrors is divided into three scenarios: left-side mirror, right-side mirror, and center mirror. Below is a detailed introduction to the optimal positions for these three scenarios: 1. Left-side mirror: The driver should use the horizon as a reference. By adjusting the vertical angle, the mirror should display an equal split between the sky and the ground. Additionally, regarding the horizontal angle, the car body should occupy about 1/4 of the mirror's surface. Note that the adjustment of the car's rearview mirror should be based on the driver's seating position. 2. Right-side mirror: Since the right-side rearview mirror is the farthest from the driver's position, the space occupied by the sky in the right-side mirror should be minimized. More space should be allocated to the side of the car body. Therefore, the sky should occupy only 1/4 of the right-side mirror, and the car body should also occupy 1/4. 3. Center mirror: The adjustment is relatively simple. The optimal position is one where the rear window can be seen clearly through the mirror to observe the situation behind the car. The ground and sky should each occupy half of the center mirror.
16
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.