Where is the steering angle sensor located on the Baojun 730?

1 Answers
StIsaac
07/28/25 11:33pm
The steering angle sensor on the Baojun 730 is located on the electric power steering column above the steering wheel. The function of the steering angle sensor is to detect the rotation angle and direction of the steering wheel. Taking the 2019 Baojun 730 as an example, its body dimensions are: length 4780mm, width 1780mm, height 1740mm, wheelbase 2750mm, and fuel tank capacity 52 liters. The 2019 Baojun 730 is equipped with a 1.5T turbocharged engine, delivering a maximum horsepower of 147PS, maximum power of 108kW, maximum torque of 250Nm, and paired with a 6-speed manual transmission.
Was this review help?
5
4
Share
More Forum Discussions

How to Use a Car Fire Extinguisher?

First is the optimal placement position, generally placed within easy reach of the right hand to ensure the timeliness of firefighting actions. Pull out the safety pin, hold the fire extinguisher body with one hand, firmly press the extinguisher handle with the other hand, and aim at the base of the flame to spray.
19
1
Share

How to Use a Car Phone Mount?

Vent-mounted phone holder installation: Prepare the holder and the vent mounting clip. Unscrew the knob on the back of the holder, insert the mounting clip, and tighten the knob. Select a suitable vent, press the spring clip on the mounting clip to secure it in place.
15
5
Share

How to Install a Car Phone Mount?

Vent-mounted phone holder installation: Prepare the holder and vent attachment clip. Loosen the knob on the back of the holder, insert the attachment clip, then tighten the knob. Select a suitable air vent, press the spring clip on the attachment to secure it in place.
7
3
Share

What does TC mean when displayed in the car?

When the TC indicator appears on the car's dashboard, it means the Traction Control system is active. TC stands for Traction Control System, which functions to prevent wheel slippage and potential loss of directional control when braking on slippery surfaces or during rapid acceleration from a stop. The Traction Control System relies on ABS anti-lock braking system electronic sensors. When it detects that the speed of the driven wheels is lower than that of the driving wheels (indicating wheel slippage), it sends feedback signals to the vehicle's system. The system then adjusts ignition timing, reduces throttle opening, decreases fuel supply, downshifts, or applies braking to the wheels to prevent slippage.
10
5
Share

How to Read the Digital Tire Pressure Gauge on a Car Air Pump?

How to read the values on a car air pump: First, check the unit. If it's BAR, inflate to 2.4 or 2.8; if it's PSI, inflate to 35-40; if it's KPA, inflate to 240-280. There is an M button for settings—set the preset value, then start inflating. The pump will stop automatically when the preset value is reached. If there is no preset function, inflate directly while monitoring the value and stop when the desired pressure is reached. Some gauges have a red line between 2-3, which indicates the normal tire pressure range for most vehicles. You can stop when the pointer reaches the middle of this range, though this method is less precise compared to setting a numerical value. According to the international GBT2978-2008 standard, the recommended tire pressures are as follows: Standard tires: 2.4-2.5bar; Reinforced tires: 2.8-2.9bar; Maximum pressure: should not exceed 3.5bar.
18
2
Share

How to Replace Wiper Blades?

Replace Wiper Blades by following these steps: 1. Lift the wiper arm naturally upwards along the direction of the wiper to separate it from the car body; 2. Tilt the wiper blade backward to make it perpendicular to the wiper arm; 3. Locate the fixing buckle at the connection between the wiper blade and the wiper arm; 4. Pull the tab outward and then push the wiper blade outward to open it; 5. Pull the buckle sideways to release it from the wiper blade connection; 6. Separate the wiper blade from the wiper arm; 7. At the corresponding port, gently insert a flat-head screwdriver about 1cm into the rubber blade, wrap the cover with a cloth, and pull the rubber blade outward; 8. Use the screwdriver to lightly pry open the hook to detach it from the rubber blade; 9. Remove the old rubber blade and replace it with a new one.
9
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.