Where is the spark plug located on the Baojun 730?

1 Answers
StCollin
07/29/25 7:50pm
Location of the spark plug on the Baojun 730: The spark plug is installed on the side or top of the engine. In earlier models, spark plugs were connected to the distributor via ignition cables. However, over the past decade, most car engines have been updated to feature direct connections between the ignition coil and the spark plug. How spark plugs work: The spark plug's ground electrode is connected to the metal shell, which is threaded into the engine block via the cylinder head. The insulator primarily serves to isolate the metal shell from the central electrode. The terminal nut is the part of the spark plug that contacts the high-voltage coil. When current passes through the terminal nut and the central electrode, it ionizes the medium between the central electrode and the ground electrode, generating a spark that ignites the air-fuel mixture in the cylinder.
Was this review help?
4
0
Share
More Forum Discussions

Can I Continue Driving When the Fuel Light Flashes?

You can continue driving for a short distance when the fuel light flashes. If the fuel light comes on in urban areas or under poor road conditions, try to maintain a steady speed and avoid sudden acceleration. It is recommended to refuel at the nearest gas station as soon as possible. This is to prevent both the inability to find a gas station and uneven engine cooling, which could cause damage to the engine. If the fuel tank is low, it may damage the fuel pump or shorten its lifespan. This is because the fuel pump is cooled by the gasoline, which helps dissipate heat. When the fuel light comes on, it indicates that the gasoline level is too low to cover the fuel pump, preventing effective cooling. This can lead to the fuel pump overheating and failing, causing the car to malfunction.
4
3
Share

How to Turn On the Rearview Mirror Heating in a Lincoln?

There are two designs for the rearview mirror heating control switch: one is integrated with the electric rearview mirror adjustment combination switch, and the other is located on the air conditioning control panel. The rearview mirror heating button icon looks very similar to the front windshield defogger, but upon closer inspection, there are noticeable differences. The one with a curved arrow is the heating button. After pressing the button, the heating element behind the rearview mirror glass will quickly heat up to a fixed temperature within a few minutes, usually between 35-60 degrees Celsius. When using the rearview mirror heating function, ensure the vehicle is in an ignited state and try to avoid using this function when the engine is cold.
8
5
Share

How to Drive When the Manual Transmission Clutch Fails?

When the diaphragm spring is installed between the clutch cover and the pressure plate, the pre-compression deformation generates pressure on the pressure plate, which tightens the driving and driven parts of the clutch. When the driver depresses the clutch pedal, the pedal moves left, pushing the push rod left, which in turn moves the diaphragm spring release plate left through the master cylinder and slave cylinder. When the driver releases the clutch pedal, the pedal returns to its original position under the action of the return spring, simultaneously bringing the push rod and release bearing back to their positions. After disengagement, the engine's power and motion cannot be transmitted to the driven plate. The driving part remains synchronized with the engine speed, while the driven part rapidly decreases.
20
1
Share

What type of engine oil does the Warrior use?

The Warrior uses either fully synthetic or semi-synthetic engine oil. In terms of powertrain, the Warrior offers three variants: gasoline-powered models equipped with 2.0T and 2.4T turbocharged engines, and a diesel version powered by a 2.5T turbocharged diesel engine. Since this vehicle features turbocharged engines, it requires higher-performance engine oil for optimal protection. There are three types of engine oils used in vehicles: mineral oil, semi-synthetic oil, and fully synthetic oil, each serving different purposes with varying service intervals. Typically, mineral oil requires replacement every 5,000 km, semi-synthetic oil every 6,500 km, and fully synthetic oil every 10,000 km. The Warrior measures 4710mm in length, 1825mm in width, 2120mm in height, with a wheelbase of 2800mm.
12
4
Share

Do I need to register a spoiler that does not exceed 30 cm?

A spoiler that does not exceed 30 cm needs to be registered. Introduction to Car Spoilers: A car spoiler refers to the protruding ducktail-shaped component installed at the rear end of the car's trunk lid, which is part of the car's aerodynamic kit. Its main function is to reduce the lift at the rear of the vehicle. Spoilers are generally divided into single-layer and double-layer types, made of either aluminum alloy or carbon fiber materials. They can also be manually adjustable or hydraulically automatic adjustable, with the latter featuring multiple hydraulic struts that automatically adjust the angle based on the vehicle's speed. How Spoilers Work: When a car is moving at high speed, according to the principles of aerodynamics, it encounters air resistance during movement. Around the car's center of gravity, aerodynamic forces are generated in three directions: longitudinal, lateral, and vertical lift, with the longitudinal force being the air resistance.
14
4
Share

How often should the brake pads on the Chery Tiggo 3 be replaced?

The brake pads of the Tiggo 3 should be replaced every 60,000 kilometers or 4 years. Here is some information about the Tiggo 3 brake pads: 1. Function: Automotive brake pads, also known as automotive brake linings, refer to the friction materials fixed on the brake drums or discs that rotate with the wheels. The friction linings and blocks within them withstand external pressure to generate friction, thereby achieving vehicle deceleration. 2. Working Principle: The working principle of brakes mainly relies on friction. By utilizing the friction between the brake pads and the brake discs (or drums), as well as between the tires and the ground, the kinetic energy of the moving vehicle is converted into heat energy through friction, bringing the vehicle to a stop. A good and efficient braking system must provide stable, sufficient, and controllable braking force, along with excellent hydraulic transmission and heat dissipation capabilities. This ensures that the force applied by the driver on the brake pedal is fully and effectively transmitted to the master cylinder and slave cylinders, while avoiding hydraulic failure and brake fade caused by excessive heat.
1
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.