Where is the reset button located on the Buick GL8?

2 Answers
SanSara
07/29/25 9:28am
The reset button on the Buick GL8 is located at the lower left corner of the center console dashboard. The literal translation of "Reset" means reset, clear, or restore. Its function is to basically reset the information in the car's dashboard information center, except for the total mileage. Holding it down for up to 3 seconds can clear the data. Here is more information about the Buick GL8: 1. Body dimensions: The Buick GL8 is a popular joint-venture MPV model, with a body length, width, and height of 5256mm, 1878mm, and 1776mm respectively, and a wheelbase of 3088mm. 2. Power: The car is equipped with a 3.0L VVT V6 engine, with a maximum horsepower of 178 and a top speed of 168km/h.
Was this review help?
19
5
Share
Seth
08/12/25 10:03am
When I first drove the Buick GL8, the reset button was on the control stalk to the left of the steering wheel—not a standalone button, but a small protrusion hidden on the turn signal lever. It was used to reset the trip odometer, like when you finish a long drive and want to record a new trip; just hold it down for a few seconds to clear the data. Last time after servicing, the technician forgot to do it, and the dashboard light kept flashing as a reminder, so I had to manually reset it to fix the issue. The button’s position is a bit hidden, especially in sunlight where it’s hard to see and easy to accidentally press. I recommend operating it while parked to avoid distraction on the road. The GL8’s design is quite consistent, but minor adjustments may exist across model years—post-2020 versions relocated it to the steering wheel button cluster. Checking the user manual’s diagram on page 35 is much better than guessing. Remember, though small, this button is quite useful—don’t overlook it during regular maintenance.
Was this review help?
9
1
Share
Expand All
More Forum Discussions

Which Piece of Car Glass is the Most Valuable?

The most valuable piece of glass in a car is the triangular window glass located at the rear seats, despite being a very inconspicuous small piece. Here are the relevant details: 1. Function of the triangular window glass: It assists the driver in observing the rear situation, reducing blind spots and enhancing safety. Additionally, due to the structural design of the car, it improves the overall stability of the vehicle body. These two functions make the triangular glass significant, hence it is the most valuable car window glass. 2. Precautions: If the glass is damaged, it should be replaced promptly to avoid any adverse consequences from shattering during driving.
18
2
Share

Can Carlife Connect Wirelessly?

Baidu Carlife for Android can connect wirelessly. Regardless of the smartphone's operating system, Baidu CarLife users can safely and conveniently use a variety of applications while driving by simply connecting their phones to the vehicle's system via a data cable or WiFi. Below is an introduction to the main functions of Baidu Carlife: 1. Map Navigation: Voice input with intelligent announcements, automotive-grade HMI interface design, connection to vehicle data for high-precision navigation. 2. Music: Play local music, listen to online music or radio, and support for third-party service integration. 3. Phone: Make and receive calls, synchronize and browse mobile phone contacts, view call history.
13
3
Share

Why does the BMW X3 jump to P gear after start-stop?

BMW X3 jumps to P gear after start-stop for the following reasons: Accidental button press: After parking, you or someone else in the car accidentally pressed the P gear button; Ignition device shutdown: If the ignition device is turned off, the engine will shut down, and the gear will automatically shift from R or D to P gear. The ignition device will automatically shut down under the following circumstances: when the car is in interlock mode, if the low beam is on. Before the battery is completely discharged, to ensure the engine can be started next time, the ignition device will automatically shut down. When the driver's seat belt is fastened and the low beam is off, opening the door will trigger this. Engine shutdown: If the radio is in standby mode and the engine is shut down, the gear will also automatically shift from R or D to P gear.
18
1
Share

What is the logo of Lincoln?

The logo of Lincoln is a star, or you can say a cross, placed in the middle of a rectangle, which is set to commemorate President Lincoln. Below is an introduction to the Lincoln Navigator: 1. Exterior: The front of the Navigator is the most distinctive part, fully inheriting the Lincoln heritage and reflecting the bold and steady characteristics of American cars. The all-aluminum body not only enhances the overall rigidity of the vehicle but also significantly reduces the total weight, improving the vehicle's power and fuel economy, which is commendable. 2. Configuration: The full LCD instrument panel has a very clear display resolution, and the multimedia LCD screen in the center responds quickly with powerful functions. The gear shift buttons below use a horizontal layout.
12
0
Share

How to Turn Off the Auto Start-Stop Function When Opening the Door in an Audi?

Regarding the method to turn off the auto start-stop function when opening the door in an Audi, the steps are as follows: 1. Locate the start-stop system button on the vehicle's center console or behind the gear lever. The function is enabled by default when the vehicle leaves the factory, indicated by the "yellow light off." Pressing this button will turn on the yellow light, deactivating the start-stop function (OFF means "closed"). 2. The start-stop function will cause the vehicle to shut off. Repeatedly pushing and pulling the transmission gear lever back and forth may result in multiple gear shifts within a short period. 3. The vehicle will interpret this as a child's accidental or improper operation. For the safety of both the vehicle and its occupants, the vehicle will automatically shut off.
2
1
Share

How to Identify China 4 and China 5 Emission Standards for Vehicles?

Here are the methods to distinguish between China 4 and China 5 emission standard vehicles: 1. Check the corresponding standard number on the vehicle conformity certificate: The emission standard number for China 4 is GB18352.3-2005; for China 5, it is GB18352.5-2013. 2. Check the environmental information vehicle list: The emission standard is clearly marked on it. 3. Check the vehicle fuel consumption label: It is usually posted on the side window of the vehicle. 4. Query the vehicle's emission standard on the Motor Vehicle Environmental Protection Website: Open the website and find the public information query at the bottom of the page, then enter the last 6 digits of the VIN and engine number to check the vehicle's emission standard.
10
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.