Where is the rearview mirror heating switch on the 2021 Nissan Qashqai?

2 Answers
Logan
09/05/25 6:53am
The rearview mirror heating button on the 2021 Nissan Qashqai is located in the middle key at the bottom of the control panel, featuring a square frame with three upward curved arrows. Pressing this button activates the rearview mirror heating function. Rearview mirror heating is particularly useful during rainy or snowy weather. When activated, the heater behind the mirror quickly warms the surface, gradually removing rain or fog, eliminating the need for frequent manual wiping by the driver and thereby reducing driving hazards. Methods to use the rearview mirror heating function: There are generally two ways to activate the rearview mirror heating function. One is combined with the electric rearview mirror adjustment button—simply rotate the knob to turn it on. The other is located on the air conditioning control panel, where pressing the heating button activates the function. No manual angle adjustment is needed, as there is an adjustment button on the driver's side. Principle of the rearview mirror heating function: After pressing the button, the electric heater behind the rearview mirror glass rapidly heats up to a fixed temperature within minutes, typically between 35-60 degrees Celsius. The heat is then emitted from the left and right rearview mirrors. Simultaneously, as the temperature rises and evaporates, water droplets on the mirror surface become smaller, and fog gradually disappears, effectively defrosting and defogging the mirror. However, if the rain is particularly heavy, the effect may diminish and become less noticeable. Precautions for using the rearview mirror heating function: The principle of rearview mirror heating involves adding electric heating wires to the mirror, which consume a significant amount of power. When using this function, ensure the car is in an ignited state. Avoid activating the rearview mirror heating while the car is stationary to prevent draining the battery and potentially leaving insufficient power to start the vehicle. Other methods to defog rearview mirrors include: Opening windows slightly: Creating a gap in the side windows allows air convection between the inside and outside of the car, reducing the temperature difference and gradually eliminating fog. Adjusting the car's air conditioning to the appropriate setting can also help by blowing warm air to defog the mirrors.
Was this review help?
20
3
Share
LeAutumn
09/17/25 7:11am
I noticed that the rearview mirror heating switch for the 2021 Nissan Qashqai is located on the center console's air conditioning control panel. That button with wavy lines and a square outline icon is usually integrated with the windshield defogging function—a single press activates both simultaneously. This design is quite user-friendly. When driving in rainy weather, I rely on it to clear fog and rainwater from the mirrors, improving visibility. As an experienced driver, I recommend ensuring the exterior mirror surfaces are free of debris before activating it, otherwise the heating efficiency may be compromised. Some friends complain about not finding it, but a closer look at the button's icon—which represents fog dissipation—should help; don't mistake it for a separate switch. Most Nissan models arrange it this way, making efficient use of space. If you still can't locate it, check the user manual or search carefully under interior lighting—developing this habit ensures safer driving. Though a small feature, the rearview mirror heating function proves invaluable, especially in winter or humid conditions, safeguarding driving safety.
Was this review help?
6
3
Share
Expand All
More Forum Discussions

Where is the water drain groove in the subject 2 test vehicle?

The front windshield water drain groove is located under the front windshield, specifically the plastic guide channel beneath the front wipers. 1. Automobile water drain groove: As a crucial component of the vehicle body system, it serves as the primary drainage pathway for the car body, effectively collecting and discharging rainwater to prevent water ingress into the vehicle interior or cabin. Depending on whether the outlet is positioned at the end or bottom of the groove, automobile water drain grooves can be categorized into side-drainage grooves and bottom-drainage grooves. 2. Function: Typically installed behind the wheel housing of the vehicle body, the water drain groove often incorporates reinforcement plates to enhance the wheel housing's strength. However, these reinforcement plates may obstruct the drainage ports at the ends of side-drainage grooves, impairing their functionality. Creating openings in the reinforcement plates would compromise their structural integrity. In contrast, bottom-drainage grooves feature drainage holes at the base that connect to the external environment and remain unaffected by reinforcement plates. Installing bottom-drainage grooves behind the wheel housing effectively resolves drainage issues.
16
4
Share

Where should the front bumper stop during the slope start in Subject 2?

Car front bumper should be positioned on the pile rod line, with no more than 50cm deviation front or back. Extended information: 1. Positioning: When positioning, you need to find reference points on the vehicle body, such as: wiper reference points and test site marker poles, while also ensuring clear three-point alignment in your line of sight. However, the key point is mainly to find good reference objects, as they are the focus - otherwise it would be a case of 'move one and affect the whole'. 2. Don't rush: The most crucial aspect during startup is not to rush, as there's definitely sufficient time. Control the clutch properly and absolutely avoid stalling the vehicle. If rolling back causes a stall, brake immediately. Note that when preparing to start on a slope, remember to first turn on the turn signal, then release the clutch, and when the vehicle body vibrates, slowly lift the brake.
8
4
Share

How to Check if a Thermostat is Good or Bad?

There are mainly the following methods to check whether a thermostat is good or bad: 1. When the engine starts cold operation, if there is still coolant flowing out at the inlet pipe of the upper water chamber of the radiator, it indicates that the main valve of the thermostat cannot close. 2. When the engine coolant temperature exceeds 70°C, if there is no coolant flowing out at the inlet pipe of the upper water chamber of the radiator, it indicates that the main valve of the thermostat cannot open normally, and repair is needed at this time. The function of the thermostat is to automatically adjust the amount of water entering the radiator according to the temperature of the coolant, change the circulation range of the water, and adjust the heat dissipation capacity of the cooling system to ensure that the engine works within a suitable temperature range. The thermostat must maintain good technical condition, otherwise it will seriously affect the normal operation of the engine. If the main valve of the thermostat opens too late, it will cause the engine to overheat; if the main valve opens too early, it will prolong the engine preheating time and make the engine temperature too low.
5
5
Share

What class of sedan is the Roewe i6max?

Roewe i6max is a compact car with dimensions of 4722mm (length), 1835mm (width), 1464mm (height), and a wheelbase of 2715mm. Below is an introduction to the Roewe i6max: 1. The Roewe i6max is equipped with a 1.5-liter turbocharged four-cylinder engine across all variants. It delivers a maximum power of 127kW and a peak torque of 275Nm. The engine reaches its maximum power at 5600 rpm and its peak torque between 1750 to 4000 rpm. This engine features direct fuel injection technology and utilizes an aluminum alloy cylinder head and block. It is paired with a 7-speed dual-clutch transmission. 2. The Roewe i6max employs a MacPherson strut independent suspension at the front and a multi-link independent suspension at the rear. The multi-link suspension is a structurally complex independent suspension system that replaces the two arms of a double-wishbone suspension with separate links.
15
5
Share

What is the standard for stopping in Subject 2 of the driving test?

A pause of more than 2 seconds is considered an intermediate stop. In the driving license Subject 2 test, an intermediate stop is determined when the GPS positioning confirms that the vehicle is in a completely stationary state during the test. Additional information: 1. Time limit: If you fail the Subject 2 test once, you can retake it once. If you do not take the retest or fail the retest, the current test is terminated, and the applicant must reschedule the test after ten days. Within the validity period of the driving skill permit, the number of scheduled tests for Subject 2 and Subject 3 road driving skills tests must not exceed five times. If the fifth scheduled test is still failed, the results of other subjects that have been passed will be invalidated. 2. Revised regulations: Starting in 2017, the new driving test regulations revised the rules regarding intermediate stops in Subject 2. Before the revision, stopping during the reverse parking test would result in failure, but after the reform, each intermediate stop during reverse parking deducts 5 points.
6
0
Share

How to Turn on the Octavia's Air Conditioning?

For the Octavia's air conditioning, pressing the AC button activates the compressor switch, which is the cooling switch. The left side controls temperature - green indicates lower temperature while red indicates higher temperature. The middle section adjusts the fan speed levels. Below is an introduction to car air conditioning: 1. The car air conditioning device (air-conditioning-device), abbreviated as car AC, is used to regulate and control the temperature, humidity, air cleanliness, and airflow within the vehicle cabin to optimal conditions. It provides passengers with a comfortable environment, reduces travel fatigue, and creates favorable working conditions for drivers, playing a crucial role in ensuring safe driving. 2. It generally includes cooling devices, heating devices, and ventilation systems. This integrated system makes full use of the limited interior space of the vehicle, featuring a simple structure and easy operation, making it the internationally popular modern car air conditioning system. 3. The functions of automatic air conditioning include automatic adjustment of interior temperature and humidity, automatic control of air recirculation and supply modes, as well as operation methods and air exchange volume control.
18
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.