Where is the rearview mirror heating for the Lynk & Co 03 located?

1 Answers
McMichael
07/29/25 7:39pm
The rearview mirror heating for the Lynk & Co 03 is located on the fourth button below the central control screen. The Lynk & Co 03 is a compact sedan with body dimensions of 4657mm in length, 1840mm in width, and 1460mm in height, with a wheelbase of 2730mm. The Lynk & Co 03 is equipped with three turbocharged engines: a low-power 1.5-liter turbocharged engine, a high-power 1.5-liter turbocharged engine, and a 2.0-liter turbocharged engine. The low-power 1.5-liter turbocharged engine has a maximum power of 115 kW and a maximum torque of 245 Nm; the high-power 1.5-liter turbocharged engine has a maximum power of 132 kW and a maximum torque of 265 Nm. The 2.0-liter turbocharged engine has a maximum power of 140 kW and a maximum torque of 300 Nm.
Was this review help?
3
0
Share
More Forum Discussions

What is the tightening and loosening direction of the nuts on car tires?

Car tire nuts are loosened by turning counterclockwise and tightened by turning clockwise. Precautions for changing tires include: 1. Removing the tire: When removing the tire, loosen the fixing screws counterclockwise and place the jack in the jack slots on both sides of the car bottom to avoid accidents; 2. New tire inspection: Before changing the tire, the owner should check whether the replacement tire is normal to avoid unnecessary safety hazards; 3. Operation sequence: When changing the tire, pay attention to screwing in four screws diagonally first, then the fifth screw, ensuring each screw is turned the same number of times to ensure even force distribution.
19
3
Share

Does Car Waxing Damage the Paint?

Car waxing does not damage the paint. However, excessive polishing and waxing can harm the paint. This is because there is a protective layer on the paint, approximately only 0.5mm thick. Each polishing session thins this protective layer, and improper operation can easily expose the primer. Therefore, it is not recommended to perform polishing and waxing too frequently. Benefits of waxing: Waterproofing effect, reducing watermarks, dark spots, rust, and damage on the paint surface; Anti-aging effect, reducing UV damage to the paint and extending the paint's lifespan; Gloss enhancement, improving the paint's smoothness to varying degrees and making the car's color more vibrant; Anti-static effect, reducing damage caused by friction with dust, wool fabrics, and synthetic fibers in the air; Anti-corrosion effect, effectively isolating damage from acid rain and acid mist to the paint. Car waxing cycle: For cars frequently parked indoors, waxing once every 4 months is sufficient; for cars frequently parked outdoors, waxing once every 2 months is sufficient. Since car wax generally lasts for a short time, usually around 1-2 months, waxing can be performed when the body feels rough to the touch or shows imperfections.
12
2
Share

Where is the largest used car trading market in China?

China's largest used car trading market is located in Shenzhen, at the Aukangda Luxury Car Plaza. Below are specific details about the used car trading market: 1. Trading methods: With the development of the used car trading market, various forms of used car trading markets have emerged in the country, including traditional used car trading markets, the Fair Price used car internet platform, used car trading companies, and used car exchange companies. 2. Functions: Its main function is to introduce multiple features such as automotive culture, technology, science education, exhibitions, tourism, and entertainment on the basis of a standard used car market.
16
2
Share

What are the steps for warming up the car in the morning?

The steps for warming up the car in the morning are: After starting the vehicle, let it idle for 1 to 2 minutes to allow the engine coolant to reach normal temperature before driving. The purpose of warming up the car is: 1. After the car has been parked for a long time, the engine oil flows back into the oil pan, leaving the upper part of the engine in a state of insufficient lubrication. Warming up helps lubricate the engine. 2. When the engine has not reached its operating temperature, the fuel supply system cannot effectively vaporize gasoline completely due to the low temperature. 3. When the car is cold, the gear oil flows to the lower part of the transmission. Only when driving does the rotation of the gears bring the gear oil up to lubricate the upper part.
12
0
Share

Can I Drive in the Rain Right After Applying Paint Protection Film?

You should avoid driving in the rain immediately after applying paint protection film (PPF) because the film has not yet fully bonded with the car's paint within the first 24 hours. Small air bubbles may still be present, which require time and exposure to sunlight to dissipate. Additionally, the edges of the newly applied PPF may not be securely adhered, so it's best to let the car sit for a few days to ensure the film becomes more firmly attached. Below are some precautions for using paint protection film: 1. Once the PPF has fully bonded with the car's paint, rain will not affect it, as water cannot penetrate the film. 2. For the first month after application, avoid using high-pressure water jets on the seams of the PPF, as this could loosen the edges and reduce its protective effectiveness. 3. When washing the car, avoid scrubbing the PPF surface with hard objects or excessive force, as scratches and wear can diminish the film's shine and appearance. 4. During long-term use, avoid parking the car outdoors under direct sunlight for extended periods, especially in summer, as strong UV rays can cause the PPF to yellow. 5. Do not leave the car parked in rainwater for long periods, as acidic substances in the rain can erode the surface of the PPF.
16
5
Share

What Material is Best for Car Engine Guards?

Engine guard materials include steel plate, reinforced resin, plastic, and aluminum alloy. Below is relevant information: 1. Pros and Cons: Steel plate is currently the most chosen by car owners due to its low cost and hard material, offering the best protection for the engine. However, it is heavy, affects chassis weight distribution, and may interfere with engine safety sinking in severe accidents. Reinforced resin is much lighter than steel and can easily handle minor scratches and mud erosion, but its overall strength is inferior to steel, making it prone to breaking in slightly severe undercarriage impacts. Plastic guards are lightweight and inexpensive, but they are very thin and weak, often breaking with minor scratches, making them the lowest-grade product. Many low-end cars come with plastic guards as standard. Aluminum alloy guards are lightweight, high-strength, and have an excellent appearance. 2. How to Choose: This depends on road conditions and driving environment. If driving on very poor, bumpy roads or frequently off-roading, install the most durable and impact-resistant steel guards for better chassis protection. Some off-road vehicle guards are even made of high-strength steel plates. If driving mostly in cities or on highways, reinforced resin or plastic guards are sufficient, mainly to block mud and water. As for aluminum alloy engine guards, they offer numerous advantages.
15
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.