Where is the rearview mirror heating button on the Changan CS55?

1 Answers
Todd
07/30/25 4:13am
The rearview mirror heating switch of the Changan CS55 is located on the far side of the dashboard. Press the button, and the indicator light will illuminate. The rearview mirror heating function is particularly useful during rainy or snowy weather. When activated, the heater behind the mirror quickly warms the mirror surface, gradually removing rainwater or fog, eliminating the need for the driver to manually wipe the mirrors frequently, thereby reducing driving hazards. Principle of the rearview mirror heating function: After pressing the button, the electric heater behind the rearview mirror glass rapidly heats up to a fixed temperature within minutes, typically between 35-60 degrees. The heat is then dissipated from the left and right rearview mirrors. Simultaneously, as the temperature rises and evaporation occurs, water droplets on the mirror surface gradually decrease, and fog slowly disappears, effectively heating the mirror and removing frost. However, if the rain is particularly heavy, the effect may diminish and become less noticeable. Precautions for using the rearview mirror heating function: The principle of rearview mirror heating involves adding electric heating wires to the mirrors, which consume a significant amount of power. When using the rearview mirror heating function, ensure the car is in an ignited state. Avoid activating the heating function when the car is stationary to prevent draining the car battery, which could leave insufficient power for starting the vehicle. Other methods for defogging rearview mirrors include: Opening windows for air circulation: Slightly open the windows on both sides to allow air to flow between the inside and outside of the car, reducing the temperature difference and gradually eliminating fog. Adjust the car's air conditioning to the appropriate setting to use the warm air blown by the AC for defogging.
Was this review help?
12
1
Share
More Forum Discussions

How to Turn On and Off the Car Child Lock?

Car child lock can be turned on and off as follows: 1. Open the rear door of the car. 2. Locate the position of the child lock. 3. Toggle the switch to set the child lock to the off position. 4. Close the door to complete the locking process. 5. To open, it can only be done from the outside. More information about car child locks is as follows: 1. The car child safety lock, also known as the door lock child safety, is installed on the rear door lock of the car. 2. The car child safety lock is used for the rear doors of the vehicle to prevent the danger of opening the door from the inside while the vehicle is in motion.
10
2
Share

What is the normal voltage of an oxygen sensor?

The normal voltage of an oxygen sensor ranges between 0.1 and 0.9V. Here are the specific details about oxygen sensors: 1. The oxygen sensor is a standard configuration in automobiles, utilizing the Nernst principle; 2. It measures the oxygen potential in the exhaust pipe of a vehicle using a ceramic sensitive element, calculates the corresponding oxygen concentration based on chemical equilibrium principles, and serves as a measuring component to monitor and control the air-fuel ratio of combustion to ensure product quality and compliance with exhaust emission standards; 3. It features advantages such as simple structure, rapid response, easy maintenance, convenient use, and accurate measurement.
20
1
Share

What Causes the Abnormal Noise from Car Windows?

Reasons for abnormal noise from car windows: 1. Loose fit between the window regulator and the door: Although the window appears to be fully raised, the glass may not be tightly sealed, causing noise with slight road bumps. 2. Aging of the vehicle's sealing strips: When the sealing strips age, their adherence to the glass decreases, leading to glass movement and subsequent noise. 3. Debris on the glass surface: Small cards placed in window gaps by advertisers can widen the gaps, and the debris itself may produce noise at high speeds. 4. Aging of the door's fuzzy strips: These strips clean the glass surface and secure the glass to prevent movement.
20
5
Share

Is Fuel Additive Suitable for New Cars?

New cars are not suitable for fuel additives. Since the effects of fuel additives are relatively limited, and the fuel at domestic gas stations already contains fuel additive components, coupled with the fact that new car engines have short service lives and good working conditions, they basically do not produce carbon deposits. Therefore, there is no need to add fuel additives to new cars. Below is an introduction to the functions of fuel additives: 1. High-quality gasoline additives contain cleaning and activating factors that can promote the removal of gum substances in fuel and harmful substances such as engine carbon deposits. After continuous use, carbon deposits on the exhaust pipe are significantly reduced, and components such as filters, exhaust valves, and fuel systems remain very clean. 2. They clean the fuel system and remove carbon deposits.
15
2
Share

What is the correct method for removing carbon deposits from a car?

Correct methods for removing carbon deposits from a car: 1. Hang a bottle-shaped tool above the engine, pour the cleaning agent into the bottle tool, and introduce it into the engine through a conduit to achieve the purpose of cleaning carbon deposits; 2. Inject the cleaning agent into a machine, then pressurize it into the combustion chamber, allowing the cleaning agent to react with and dissolve the carbon deposits, and then extract the waste liquid. Carbon deposits occur in the engine combustion chamber when there is insufficient oxygen supply, leading to incomplete fuel combustion and the production of oil smoke. Over time, oil, dust, and debris can leave sludge in the engine, and the sludge in the cylinders is referred to as 'carbon deposits.'
5
5
Share

Why is one brake light on and the other not working?

One brake light being on while the other isn't working is usually caused by a burnt-out filament in the brake light bulb. After prolonged use, the filament can deteriorate due to aging, preventing the brake light from functioning properly. In such cases, the bulb needs to be replaced promptly. If the issue lies with the wiring, professional diagnosis and repair will be required. Steps to replace the brake light switch: 1. Remove the protective panel above the brake and accelerator pedals to access the brake light switch; 2. Disconnect the corresponding wiring harness and remove the switch (note: the brake light switch uses a twist-lock mechanism - turn it counterclockwise to release); 3. Install the new brake light switch and reassemble all components in reverse order.
6
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.