Where is the radiator located on the Honda City?

1 Answers
OAnderson
07/30/25 12:48am
The radiator of the Honda City is located at the front of the engine. The coolant filler port indicator can be seen between the condenser and the fan. Below are the relevant details: 1. The radiator of the Honda City contains coolant. The coolant level should be maintained between the min and max marks. If it falls below the min mark, it is necessary to add coolant of the same brand and specification; otherwise, the entire coolant must be replaced. 2. When adding coolant, first locate the radiator, unscrew the cap of the coolant reservoir, and then pour in the coolant until the level is between the two marked lines. It is not recommended to add water at this time, as prolonged use of water can corrode the radiator. 3. The car radiator absorbs heat from the engine block, preventing the engine from overheating.
Was this review help?
14
2
Share
More Forum Discussions

What is the minimum ground clearance of a fully loaded Golf?

The minimum ground clearance of a fully loaded Golf is 115mm. The minimum ground clearance of the Golf refers to the distance between the lowest point (excluding the wheels) and the supporting plane, which indicates the vehicle's ability to pass over obstacles such as stones and tree stumps without collision. A higher ground clearance in the Golf improves its off-road capability, but if the ground clearance is too high, the stability at high speeds may decrease. The Golf is built on Volkswagen's new MQB platform. The Golf's body dimensions are 4259mm in length, 1799mm in width, and 1476mm in height, with a wheelbase of 2637mm. Generally, the ground clearance of sedans ranges between 110mm and 150mm, while SUVs have a ground clearance between 200mm and 250mm. However, the Golf's ground clearance is not static; it depends on the load condition, so changes in ground clearance should be considered based on the Golf's load variations. When choosing a vehicle, ground clearance can be one of the reference factors. The decision should be based on the vehicle's intended use and the road conditions. For urban areas with well-paved roads, a vehicle with lower ground clearance can enhance stability and comfort. For long-distance travel or driving in areas with poor road conditions, a vehicle with higher ground clearance may be preferable to avoid scraping or damaging the undercarriage, considering the vehicle's off-road performance.
11
1
Share

When Should the Engine Oil Be Changed for a New Car?

For a new car, the engine oil can be changed every 5,000 kilometers, while synthetic oil can extend the interval to 8,000 to 10,000 kilometers. In terms of time, even if the car hasn't driven 5,000 kilometers within six months, the engine oil should still be considered for replacement. Engine oil plays multiple roles in the engine, including lubrication and wear reduction, aiding in cooling, sealing to prevent leaks, rust and corrosion prevention, and shock absorption. Engine oil consists of two main components: base oil and additives. The base oil is the primary constituent of the lubricant, determining its fundamental properties, while additives compensate for and enhance the performance of the base oil, making them an essential part of the lubricant.
1
3
Share

What is the general warranty period for brake discs?

The warranty period for brake discs is generally one year, but it varies among different vehicle brands. As a wear-prone component, manufacturers offer different warranty terms for brake discs. Resurfacing or machining the surface of a brake disc reduces its service life, so replacement is recommended whenever feasible. The braking system consists of multiple components, primarily the brake disc, brake pads, and electronic braking system. The brake disc and pads function interdependently - failure of either component will result in braking failure. In addition to discs and pads, brake fluid maintenance is crucial, with recommended replacement intervals of 2 years or 40,000 kilometers.
15
2
Share

What pressure should car air conditioning be charged to?

Car air conditioning should be pressurized to around 20-30 bar, which should be higher than the working pressure of the car air conditioning system. Nitrogen is generally used for pressurization and leak detection in car air conditioning systems. More details are as follows: 1. When pressurizing and checking for leaks in the car air conditioning system, use soapy water to inspect the connections of the air conditioning pipes. Whether pressurized from the high or low side, the pressure inside the system will eventually balance. Typically, nitrogen is added to the system from the high side, but Freon can also be added to the system and checked with a halogen leak detector, though this method is less effective than using soapy water. Since Freon operates at lower pressure within the system, minor leaks may be harder to detect. 2. Once the refrigeration system has been evacuated to the required vacuum level and no leaks are detected, refrigerant can be added to the system. Before charging, determine the correct amount of refrigerant to add, as too much or too little will affect the air conditioning's cooling performance. The compressor's nameplate usually indicates the type and amount of refrigerant required. 3. When using the car air conditioning system, it is important to maintain and service it properly. Avoid adjusting the air vents randomly. Some drivers do not pay attention to the direction of the airflow, which can prevent the air conditioning from performing optimally. According to the principle that cold air sinks and warm air rises, the correct approach is to direct the vents upward when cooling and downward when heating.
14
5
Share

How to Remove and Install a Car Windshield Washer Nozzle?

Methods for removing and installing a car windshield washer nozzle: 1. Locate the nozzle position, then gently pry it up using a screwdriver. The nozzle features a snap-fit design and requires minimal force; 2. Once the nozzle is pried up, you'll see a small connected hose. Simply detach the nozzle from the hose, being careful not to let the hose fall into the car, as this would necessitate removing the entire panel to retrieve it; 3. Install the newly purchased nozzle by carefully placing it into the mounting hole and pressing it downward until it clicks into place; 4. After installation, test the nozzle by spraying water to check the water stream's position on the windshield. If the stream is misaligned, use a needle to adjust the spray direction by inserting it into the nozzle hole until the desired position is achieved.
4
2
Share

Can the steering wheel not be moved during straight-line driving in Subject 3?

During straight-line driving in Subject 3, the steering wheel can be adjusted. As long as the vehicle is moving, directional changes will inevitably occur, requiring the student to make slight adjustments to the steering wheel. Below are key points about adjusting the steering wheel: 1. Lightly hold the steering wheel with both hands. Students often get nervous during the Subject 3 test, gripping the steering wheel tightly out of fear that they won't be able to correct any deviation in time. However, holding the steering wheel too tightly actually makes it harder to adjust promptly and may even cause the vehicle to deviate more. Therefore, it's essential to maintain the correct steering wheel posture. 2. Make small adjustments to the steering wheel. Straight-line driving in Subject 3 has specific speed requirements, generally faster, so large steering adjustments can easily be detected by the system as deviations and pose safety risks. Thus, students only need to make small left and right adjustments during straight-line driving. 3. Observe the surroundings. Since the straight-line driving segment in Subject 3 is strict and prohibits significant deviations, 80% of students focus solely on the road ahead to monitor the vehicle's alignment. While keeping the focus ahead is correct during the road test, the exam route also includes other vehicles and pedestrians. To avoid unnecessary collisions, students should also use their peripheral vision to observe reference points and road conditions around them, which increases the chances of success.
7
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.