Where is the position light of Volkswagen Santana Vista?

1 Answers
DiStephen
07/30/25 5:11am
The position light of Volkswagen Santana Vista is located on the fender above the front tires. It only lights up when the turn signal is activated or flashes when the hazard warning lights are turned on, serving as a warning to parallel vehicles. The position light will not illuminate unless the turn signal or hazard warning lights are activated. Other light positions of Volkswagen Santana Vista: Headlights, commonly known as high and low beams, are the largest lights on the front face of the car; rear position lights, located below the rear windshield as high-mounted brake lights, do not light up normally but form a triangular warning with the rear brake lights when the brake is pressed; fog lights, located at the very bottom of the front bumper, appear yellow and are symmetrically placed on both sides. The yellow-covered ones in the rear light assembly are also fog lights, used to warn vehicles in front and behind during heavy fog. How to turn on the lights of Volkswagen Santana Vista: There is a headlight knob on the left-hand side. Turning it one notch to the right activates the position lights, and turning it two notches activates the headlights. With the position lights already on, pulling the knob outward (like pulling a key) one notch activates the front fog lights, and pulling it two notches activates both front and rear fog lights.
Was this review help?
16
2
Share
More Forum Discussions

How to manually open the door with a smart key?

Remove the cover of the smart car door keyhole and insert the mechanical key to manually open the door. Below is an introduction to the smart: 1. Exterior: The smart Nightorange Limited Edition features a two-tone body color combining orange and black, offering a more visually striking appearance compared to the standard smart model. Additionally, the Nightorange Limited Edition is equipped with smoked headlights, black mirror covers, and an emblem with the "nightorange" inscription. 2. Powertrain: The smart Nightorange Limited Edition is powered by a 1.0-liter naturally aspirated engine and a turbocharged engine, with maximum power outputs of 70 horsepower and 84 horsepower, and peak torques of 92 N·m and 120 N·m, respectively. All models are paired with a 5-speed AMT transmission.
9
2
Share

How Does Engine Piston Slap Occur?

Engine piston slap occurs due to the following reasons: 1. Bent or twisted engine connecting rod; 2. Excessive carbon deposits in the engine; 3. Poor engine lubrication conditions; 4. High cylinder pressure at high speeds. Solutions for engine piston slap: 1. If the knocking sound disappears after the car starts and the temperature rises, you can continue driving; 2. If the knocking sound persists and becomes more noticeable after the engine reaches normal temperature, the owner should stop and inspect the vehicle promptly to prevent traffic accidents; 3. After removing the cylinder head and extracting the piston, if severe cylinder ovality, scoring, or excessive clearance between the piston and cylinder is found, replacement is necessary—replace the cylinder liner, piston, and piston rings; 4. If the connecting rod is found to be deformed, it should be replaced as much as possible.
14
1
Share

How Big Is a 10-Inch Car Navigation Screen?

10-inch car navigation screen measures 25.4cm. Below is relevant information about car navigation systems:1. Concept: A car navigation system is a driving assistance device that helps users accurately locate their current position, calculates the route based on a set destination, and guides users to the destination through map display and voice prompts.2. Operating Principle: GPS consists of three main parts: space satellites, ground monitoring, and user receivers. In space, 24 satellites form a distribution network, positioned in six quasi-synchronous orbits around the Earth, each orbit 20,000 kilometers above the ground with an inclination angle of 55°, and each orbit contains 4 satellites. GPS satellites orbit the Earth every 12 hours, enabling any location on Earth to simultaneously receive signals from 7 to 9 satellites.
5
1
Share

What is the normal water temperature for a sedan?

The normal water temperature for a sedan is between 80 to 90 degrees Celsius. The water temperature refers to the temperature of the antifreeze coolant. Inside the engine, there are oil passages and antifreeze coolant channels. The full name of antifreeze coolant is antifreeze and coolant, meaning it has antifreeze properties and serves as a coolant. It prevents the coolant from freezing during cold winter parking, which could cause the radiator to crack or damage the engine cylinder block or head. The method to replace antifreeze coolant is as follows: 1. Open the vehicle's engine hood; the coolant reservoir can be seen in the upper right corner. 2. Open the antifreeze drain plug under the radiator to drain the old antifreeze coolant. 3. Add new antifreeze coolant, tighten the cap, and the antifreeze replacement is complete.
1
3
Share

What to Do If Your Car Doesn't Have Tire Pressure Monitoring?

Solutions for cars without tire pressure monitoring are: 1. Use a tire pressure gauge or tire pressure pen to measure the pressure; 2. Have a professional 4S shop install a tire pressure monitor. Benefits of tire pressure monitors: 1. They can promptly alert you to dangerous signs in tires, preventing serious accidents; 2. They help maintain tire pressure within the specified range, reducing tire damage and extending tire lifespan; 3. They protect the shock absorption system. Tire pressure monitoring is a system that uses wireless transmission technology and highly sensitive micro wireless sensors to collect data on tire pressure and temperature, whether the car is moving or stationary. This data is then transmitted to the main unit, displaying real-time digital readings of tire pressure and temperature. If any abnormalities are detected, the system alerts the driver with a beep or voice warning.
3
1
Share

How to Bleed Air from Car Brakes?

The method for bleeding air from car brakes is: 1. Locate the bleeder screw on the brake caliper and remove the dust cap from the bleeder valve; 2. Connect the bleeder valve to a drain bottle using a rubber tube; 3. Press the brake pedal and loosen the bleeder screw on the brake caliper, repeating the process as needed. The brake is located below the driver's seat and the control panel. Braking, also known as deceleration, refers to the action of stopping or reducing the speed of moving vehicles, locomotives, or other machinery. The working principle of brakes is: a wheel or disc is fixed on the high-speed shaft of the machine, and a brake pad, band, or disc is installed on the machine base to generate braking torque under external force.
1
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.