Where is the Pajero Transmission Dipstick Located?

1 Answers
TheoLynn
07/30/25 6:40am
The Pajero transmission dipstick is located on the transmission. The method for checking the transmission fluid level involves the following steps: 1. Park the vehicle on a level surface and engage the parking brake. 2. Allow the engine to idle for at least one minute. 3. Depress the brake pedal and shift the gear selector through each position (Reverse (P), Drive (D), Low gears (S, L or 2, 1)), pausing for a few seconds in each to ensure the torque converter and all shift components are filled with hydraulic fluid. Finally, shift back to Park (P). 4. Remove the automatic transmission dipstick from the filler tube, wipe it clean, reinsert it fully, then remove it again to check the fluid level. 5. If the fluid level is between the maximum and minimum marks, the level is correct. If below the minimum mark, add transmission fluid. If above the maximum mark, the transmission has been overfilled.
Was this review help?
9
0
Share
More Forum Discussions

Why does the fault light of Baojun 510 come on?

The reasons for the fault light of Baojun 510 coming on include unqualified fuel quality, oxygen sensor failure, etc. The specific details are as follows: Unqualified automobile fuel quality: If the engine fault light on the car dashboard comes on shortly after refueling, it is generally due to incorrect or poor-quality fuel that does not meet standards, resulting in insufficient combustion of the air-fuel mixture during engine operation. Oxygen sensor failure: Currently, cars are generally equipped with two oxygen sensors, one before and one after the three-way catalytic converter. Their function is to detect the air-fuel ratio under different engine operating conditions. At the same time, the front one provides signals to the ECU for adjusting the fuel injection volume and calculating the ignition timing. The rear one is used to detect the working condition of the three-way catalytic converter.
8
1
Share

What is the reason for oil coming out of the diesel engine exhaust pipe?

The reasons for oil coming out of the diesel engine exhaust pipe are: natural wear of the power system, excessive clearance between piston rings and cylinder liners, possible overfilling of engine oil, and excessive pressure in the engine compartment. A diesel engine is an engine that obtains energy release by burning diesel fuel. It was invented by German inventor Rudolf Diesel, and to commemorate this inventor, diesel is represented by his surname 'Diesel'. Engine oil, motor oil, or engine lubricant is a substance enhanced with additives in base oil, mainly containing anti-wear additives, detergents, dispersants, and multi-grade oil viscosity index improvers. The main functions of engine oil are to reduce friction and wear of moving parts, and to remove sludge (one of the functions of dispersants) and varnish (function of detergents) from the engine.
13
0
Share

Is Antifreeze Flammable and Explosive?

Antifreeze has a boiling point of 110 degrees Celsius above zero, so it is neither flammable nor explosive. Automotive antifreeze is also not classified as a hazardous material. It is non-toxic and non-corrosive. Functions of Antifreeze: Antifreeze is a coolant containing special additives, primarily used in liquid-cooled engine cooling systems. It offers excellent performance in preventing freezing in winter, boiling in summer, and protecting against scale and corrosion throughout the year. Composition of Antifreeze: The main components of antifreeze are: 50% purified water, 40% methanol, and 10% other substances. Types of Antifreeze: Antifreeze is generally divided into three types: ethanol-water type, glycerol-water type, and ethylene glycol-water type. How to Choose Antifreeze: The basic indicators of antifreeze are its freezing point and boiling point. The market offers antifreeze with freezing points of -15℃, -25℃, -30℃, -40℃, etc. It is generally advisable to choose one with a freezing point at least 10℃ lower than the lowest temperature in your region.
17
4
Share

Does Drilling Holes for Mud Flaps Installation Affect the Car?

Yes, drilling holes for mud flaps installation typically affects the car in several ways, including reduced ground clearance, part rusting, etc. Reduced Ground Clearance: Mud flaps will lower the ground clearance of the car, affecting its off-road capability. Part Rusting: Installing mud flaps requires drilling holes in the car body for screws, which can allow rainwater to seep in and cause rust over time. Mud Flaps Turn into "Mud Scrapers": When driving on mountain roads or muddy terrain, dirt and debris can accumulate on the flaps, turning them into mud scrapers. Vehicle Instability and Increased Noise: Mud flaps can disrupt the car's aerodynamic design, creating wind resistance at high speeds, leading to instability and increased chassis noise.
5
3
Share

What is the name of the white color on the ŠKODA KAROQ?

ŠKODA KAROQ's Glacier White is a plain white. The relevant introduction of KAROQ is as follows: Model Positioning: The ŠKODA KAROQ is a compact multi-functional SUV newly designed by ŠKODA, positioned between the KODIAQ and KAMIQ. Powertrain System: The KAROQ is equipped with two turbocharged direct-injection engines from the EA211 series: the TSI230 and TSI280, paired with a 7-speed dual-clutch transmission. The TSI280 model has a maximum torque of 250Nm. The KAROQ's combined fuel consumption per 100 kilometers is 5.9L. It also features standard engine start-stop function and brake energy recovery system across the entire range, offering both robust power output and excellent fuel economy.
18
1
Share

What Causes High Engine Oil Temperature in Volkswagen Cars?

High engine oil temperature in Volkswagen cars can be caused by insufficient oil level, malfunctioning oil pump, clogged oil cooler, etc. Specific reasons are as follows: Insufficient Oil Level: When the oil level is insufficient or too high, it can easily lead to excessive oil temperature. Solution: Ensure the engine operates with the correct oil level, preferably between the upper and lower marks on the dipstick—neither too high nor too low. Malfunctioning Oil Pump: A faulty oil pump or insufficient oil delivery can result in inadequate oil pressure and poor heat dissipation. Solution: Monitor the oil pressure gauge closely to ensure the oil pump is functioning properly. If the oil pump fails, avoid attempting DIY repairs; instead, seek professional assistance. Clogged Oil Cooler: A clogged oil cooler leads to insufficient oil pressure, preventing normal heat dissipation and increasing the risk of excessive oil temperature. Solution: Regularly inspect the oil cooler and promptly repair or replace it if issues are detected.
14
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.