Where is the Odyssey Spare Tire Located?

2 Answers
VonKai
07/29/25 8:35am
The spare tire of the Odyssey is located in the floor compartment beneath the area between the driver's seat and the front passenger seat in the first row. Here is some relevant information about the spare tire: 1. How to remove the tire: First, remember that counterclockwise loosens and clockwise tightens. Loosen the tire by turning counterclockwise. Since the wheel bolts are usually very tight, you may need to use your full body strength. After loosening all the bolts, use a jack to lift the vehicle partially. When using the jack, be careful: there are several jack placement slots on both sides of the vehicle's undercarriage. Always place the jack in these slots to avoid accidents. Once the vehicle is lifted, remove the loosened bolts one by one, then take off the entire tire, which means the tire removal is complete. 2. How to install the spare tire: Before installing the spare tire, it's best to place the removed tire under the vehicle to prevent accidents in case the jack slips and the vehicle ends up resting on three wheels. The most challenging part of installing the spare tire is aligning it with the wheel bolts. If the vehicle is lifted too high, you'll need to lift the spare tire, which can be physically demanding. It's advisable to have someone assist you. If you're working alone, use your leg or foot to support the spare tire to prevent it from moving. When tightening the bolts, do not tighten them in a clockwise or counterclockwise sequence; instead, follow a diagonal pattern.
Was this review help?
4
4
Share
StSawyer
08/11/25 6:09pm
I've been driving an Odyssey for many years, and the location of the spare tire is quite clear. It's usually hidden under the car's chassis, near the rear bumper. There's a specific design for it—a small hatch with a lifting mechanism inside. You need to use the tools provided with the car (like a wrench or hook) to turn the rod and lower the spare tire. This design is quite clever because it frees up trunk space, making it easier to carry kids' stuff or travel essentials without crowding. I remember when I first bought the car, I couldn't find it, but after checking the manual, I figured it out. Just make sure not to operate it on a slope—it can be unstable. Regularly checking the tire pressure is a must, so you don’t end up in a rush during a flat tire only to find the spare is flat too. Overall, the location is user-friendly, but attention to detail is key—safety first.
Was this review help?
14
1
Share
Expand All
More Forum Discussions

What are the differences between Borui and Borui GE?

Borui and Borui GE are similarly priced, but Borui has slightly better configurations than Borui GE. The differences between the two are as follows: 1. The exterior design of Borui GE is consistent with Borui, but the interior of Borui GE has undergone significant changes: Borui GE features a full LCD instrument panel and is equipped with a yacht-style electronic gear lever. 2. Different models: Borui GE is a hybrid model, while Borui is a pure fuel version. 3. Different transmissions: Borui GE is equipped with a 7-speed dual-clutch transmission across the entire lineup, while Borui is equipped with a more stable 6-speed automatic transmission. 4. Different body dimensions: The body dimensions of Borui are 4956/1861/1513mm in length, width, and height, with a wheelbase of 2850mm. The body dimensions of Borui GE are 4986/1861/1513mm in length, width, and height, with a wheelbase of 2870mm. Borui GE has a longer body and a longer wheelbase.
14
5
Share

How to Open the Trunk of a Malibu?

The trunk can be opened or closed either electrically or via remote control. There are four steps to open the trunk of a Malibu: 1. Locate the trunk switch at the lower left corner of the driver's compartment. 2. Pull the trunk switch upward to open the vehicle's trunk. 3. Press the button on the car's remote key to also open the trunk. Below is additional information about the Malibu: 1. Body dimensions, with a wheelbase of 2.7 meters. 2. In terms of power, it is equipped with an Ecotec 2.0L or 2.4L SIDI direct-injection naturally aspirated engine, paired with a 6-speed automatic transmission.
1
2
Share

Where is the USB port of Trumpchi GM8?

There are two USB ports in the Trumpchi GS8, one in the front and one in the rear. The specific locations are as follows: 1. The front USB port is located below the center console, in front of the gear lever. 2. The rear USB port is located behind the armrest box. Precautions for using the USB port are as follows: 1. Charging is only possible when the car engine is started to avoid damage to electrical devices due to unstable power supply. 2. Do not connect too many electrical devices to avoid overloading and damaging the car battery and generator. 3. Do not use the USB port during thunderstorms to avoid lightning accidents. 4. Do not use the USB port in humid environments. Rust or water stains may cause the USB drive to fail to connect properly.
1
2
Share

Where is the Cabin Air Filter of the Soueast DX7 Located?

The cabin air filter of the Soueast DX7 is located inside the glove box on the passenger side. After opening the glove box, you can see the cabin air filter, which has the model number LAK948. Generally, it should be replaced every 8,000 to 10,000 kilometers. Below is some relevant information about the cabin air filter: It is a filter used for air purification inside the car cabin, made of highly efficient adsorption materials, such as activated carbon composite fabric combined with long-fiber non-woven fabric. The compact structure effectively filters smoke odors, pollen, dust, harmful gases, and various odors. The filter can also efficiently filter and adsorb particulate impurities, achieving oil filtration and air purification while effectively removing organic gases such as TVOC, benzene, phenol, ammonia, formaldehyde, xylene, and styrene.
10
1
Share

How to Replace the Battery of a Bestune B70 Key?

Here are the steps to replace the battery of a Bestune B70 car key: 1. Press the circular button on the side of the car key and pull out the mechanical key. 2. Use a screwdriver to pry open the gap at the top of the key. 3. Take out the key circuit board, remove the old battery, place the new battery with the positive side facing up into the slot, and gently push the battery until it is completely secured. 4. Cover the key circuit board back onto the key, align the two separated halves of the key properly, press both sides of the key with your hands until the upper and lower parts are completely fitted together, then insert the mechanical key back into the key gap to complete the process.
19
1
Share

What engine does the new Jade have?

The engine of the new Jade is produced by Honda Automobile Parts Company in Nanhai District, Foshan, Guangdong, and is a domestically manufactured engine. The engine model for the new Jade 1.5T version is L15B2, with a maximum horsepower of 156, maximum power of 115kW, and maximum torque of 203Nm. The 1.8L version engine model is R18Z6, with a maximum horsepower of 141, maximum power of 104kW, and maximum torque of 174Nm. For daily maintenance of the new Jade engine, the following methods can be used: Use lubricating oil of the appropriate quality grade. For gasoline engines, SD--SF grade gasoline engine oil should be selected based on the additional devices of the intake and exhaust systems and usage conditions; for diesel engines, CB--CD grade diesel engine oil should be selected according to mechanical load, with the selection standard not lower than the manufacturer's requirements; Regularly change the oil and filter. The quality of any grade of lubricating oil will change during use. After a certain mileage, performance deteriorates, causing various problems for the engine. To avoid failures, oil should be changed regularly based on usage conditions, and the oil level should be kept moderate; When oil passes through the fine holes of the filter, solid particles and viscous substances in the oil accumulate in the filter. If the filter is blocked and oil cannot pass through the filter element, the filter element may burst or the safety valve may open, allowing oil to bypass through the bypass valve, bringing contaminants back to the lubrication area, accelerating engine wear and increasing internal contamination; Regularly clean the crankcase. During engine operation, high-pressure unburned gases, acids, moisture, sulfur, and nitrogen oxides from the combustion chamber enter the crankcase through the gap between the piston rings and cylinder walls, mixing with metal powder from component wear to form sludge. A small amount remains suspended in the oil, while a large amount precipitates, blocking filters and oil holes, making engine lubrication difficult and causing wear.; Regularly use radiator cleaner to clean the radiator. Removing rust and scale not only ensures the engine operates normally but also extends the overall lifespan of the radiator and engine.
14
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.