Where is the OBU installed in a car?

How far can the Kicks go with a full tank?

The Kicks can travel 800 kilometers with a full tank. The fuel tank can be divided into two types: open and closed. It must have a sufficiently large volume. To keep the oil clean, the tank should have a sealed cover with an air filter installed on it. The bottom of the tank should be at least 150mm above the ground, and the anti-corrosion treatment of the inner surface of the tank should be given full attention. Taking the Kicks 2021 Manual Cool Edition as an example, its length, width, and height are 4295mm, 1760mm, and 1588mm respectively, with a wheelbase of 2620mm. The Nissan Kicks 2021 Manual Cool Edition is equipped with a 1.5L naturally aspirated engine, with a maximum power output at 6300 rpm and a maximum torque at 4400 rpm.

3

0

Share

What is the Nissan Maxima?

Maxima is the Nissan Cima. Taking the Cima 2016 2.5L XE Elite Edition as an example, its dimensions are 4903mm in length, 1860mm in width, and 1436mm in height, with a wheelbase of 1436mm. It features a MacPherson strut front suspension and a multi-link trapezoidal control arm rear suspension, with electronic hydraulic power steering. In terms of safety features, the car is equipped with driver and front passenger airbags, front side airbags, front and rear head airbags, tire pressure monitoring, ABS anti-lock braking, brake force distribution, vehicle stability control, brake assist, lane departure warning system, and autonomous emergency braking.

3

0

Share

What can be done if the car radio signal is poor?

If the car radio signal is poor, you should check for wiring issues or potential interference. Solutions vary depending on the cause: Signal Interference: Since radios primarily receive broadcast signals through antennas, signal reception quality can be affected by various factors, such as poor weather conditions leading to weaker signals compared to normal environments. Solution: If you notice reduced reception or inability to pick up certain stations after installing a new device, stop using that device. In areas with weak signals, manually adjusting the frequency band may help, though this might introduce static noise. Tinting Film Issues: Improper installation or low-quality tinting films can interfere with the radio signal, so it's important to pay attention during the initial installation. Solution: Reposition the tinting film and inspect in-car equipment carefully.

5

4

Share

What causes the ABS light on a Django to keep flashing?

There are several states in which the ABS light may illuminate, each with different causes and solutions, as detailed below: State 1: ABS warning light remains constantly on (most common). Cause 1: The ABS wheel speed sensor's detection area is covered by dirt, mud, or other contaminants, affecting the sensor's ability to detect the corresponding speed signal. This prevents the ABS computer from determining the vehicle's speed or the wheel's slip rate, thus failing to issue appropriate commands to regulate braking. Solution: Clean the dirt from the wheel speed sensor and adjust the gap between the sensor and the signal ring to restore normal function. Cause 2: Loose connections between system wires or poor contact in the ABS relay lead to signal issues, causing system failure. Solution: Inspect wire connections and reconnect any loose parts. State 2: ABS warning light intermittently illuminates but turns off during acceleration. Cause: When multiple vehicle electrical devices are in use, the battery voltage drops below 10.5V. The ABS warning light turns off as the engine speed increases and voltage rises. This may also occur if the ABS system's power supply voltage is too low due to poor wire contact or grounding issues. Solution: Check the battery's specific gravity; inspect the charging system; examine the power supply (e.g., voltage relay or poor power contact). State 3: ABS warning light stays on after engine start and only turns off when the engine is turned off (IGFF). Cause: Poor grounding contact in the ABS hydraulic valve body; poor contact in the ABS hydraulic valve body's wire connector; ABS computer malfunction. Solution: Loosen and then retighten the grounding screw on the hydraulic valve body, cleaning the contact surface if necessary; check if the connector gap has widened; replace the ABS or ABS/ASR computer. State 4: ABS warning light illuminates during high-speed driving. Cause: At high speeds, the ABS computer detects a significant discrepancy between the rear and front wheel speeds; incorrect tire or wheel rim specifications. Solution: Refer to the vehicle's tire and wheel rim specifications, as indicated on the label near the fuel tank cap. State 5: ABS warning light intermittently illuminates. Cause: Improper adjustment of the brake light switch; poor internal contact in the brake light. Solution: With the engine running, press the brake pedal and use a finger to push the brake switch linkage fully downward, then release the brake pedal to complete the self-setting position; replace the brake light switch if necessary. If the ABS warning light is on, it is advisable not to continue driving. An illuminated ABS light indicates a malfunction in the vehicle's anti-lock braking system. During emergency braking, if the wheels lock up, the vehicle may skid uncontrollably, preventing the driver from slowing down or adjusting the vehicle's trajectory, posing significant safety risks.

6

1

Share

Does replacing the windshield affect the car?

Replacing the windshield does not affect the car. However, if it is not installed properly, the glass adhesive on both sides of the windshield may not fit tightly with the glass, which can have an impact on the car. Windshields are generally made of laminated glass. Laminated glass refers to a type of transparent adhesive plastic film sandwiched between two or three layers of glass, combining the toughness of the plastic with the hardness of the glass, thereby enhancing the glass's resistance to breakage. Precautions for replacing the windshield: 1. Wear gloves to protect your hands; 2. Wear goggles when cutting glass adhesive with piano wire; 3. Use seat covers to avoid damaging the seats; 4. Use glass adhesive components; 5. When replacing a cracked windshield, use a universal windshield cutter.

2

1

Share

Will the Car Fire Extinguisher Explode Due to Bumps in the Car?

Car fire extinguishers will not easily explode due to bumps in the car, but they should be kept away from high temperatures or direct sunlight to avoid potential hazards. Below is relevant information about car fire extinguishers: Types: Car fire extinguishers are specifically designed for vehicle fire suppression and include two main types: non-stored pressure suspension ultra-fine dry powder automatic fire extinguishing devices for vehicles, and miniature stored pressure suspension ultra-fine dry powder automatic fire extinguishing devices for vehicles. Storage Location: Keep them within easy reach. It is recommended to place a portable aerosol fire extinguisher in the car cabin for emergency fire suppression. If placed in the trunk, ensure it is securely fastened. Traditional dry powder fire extinguishers and carbon dioxide fire extinguishers are relatively large in size, and these products may pose an explosion risk during high-temperature driving or vehicle bumps.

16

4

Share

Where is the OBU installed in a car?

How far can the Kicks go with a full tank?

What is the Nissan Maxima?

What can be done if the car radio signal is poor?

What causes the ABS light on a Django to keep flashing?

Does replacing the windshield affect the car?

Will the Car Fire Extinguisher Explode Due to Bumps in the Car?

Does the Mercedes-Benz GLC have ambient lighting?

What Types of Car Insurance Are Sufficient to Purchase?

How to Operate the Remote Engine Start for Mercedes-Benz Vehicles?

How to remove the maintenance reminder on CS75?