Where is the OBD port of Changan Star located?

1 Answers
DiAsher
07/29/25 6:41pm
The OBD interface of Changan Star is located next to the battery in the engine compartment of the car, and it can be seen by opening the engine hood. The full name of OBD is On-Board Diagnostics, which refers to the onboard automatic diagnostic system. This system can perform automatic diagnosis of the vehicle's status. Below is some relevant information about Changan Star: 1. The body dimensions of Changan Star are 3980mm in length, 1620mm in width, and 1890mm in height. 2. In terms of power, Changan Star is equipped with a 1.2-liter naturally aspirated engine across the entire lineup, delivering a maximum horsepower of 98hp, a maximum power of 72kw, and a maximum torque of 119nm.
Was this review help?
3
2
Share
More Forum Discussions

What is the fuel consumption per 100 kilometers for the 2015 Geely Vision manual transmission?

The fuel consumption per 100 kilometers for the 2015 Geely Vision manual transmission is 6L. Parameters of fuel consumption per 100 kilometers: Fuel consumption per 100 kilometers refers to the fuel consumption of a vehicle traveling 100 kilometers at a certain speed on the road, which is a theoretical indicator of the vehicle. The fuel consumption per 100 kilometers is a value measured by the manufacturer in an objective environment using a dynamometer installed on the vehicle's chassis, converted into speed parameters, and then calculated by specifying the speed to derive the theoretical experimental fuel consumption data per 100 kilometers for the model. Road condition fuel consumption: Road condition fuel consumption is a fuel indicator calculated by repeatedly testing the values measured when the vehicle travels at specified speeds and times on designated roads, also known as multi-condition road cycle fuel consumption.
2
1
Share

Why is the one-touch power window on the driver's side of the new X-Trail not working?

The one-touch power window on the driver's side of the new X-Trail may fail due to a battery disconnect, which can sometimes cause the one-touch window lift function to stop working. Method to restore the one-touch window lift: Ensure the ignition is ON, close the door, operate the power window switch to fully open the window, then continuously pull up the power window switch to close the window. After it is fully closed, hold the switch for more than 3 seconds, release the power window switch, and operate the window using the automatic function to confirm initialization is complete. If it still does not work properly, please contact an authorized dealer for inspection. How the one-touch window lift works: The automatic window closer only activates after the car key is turned off, and the closing function works only once. There are three modes for the automatic window closer: first, the windows automatically start closing immediately after the key is removed post-ignition off; second, the windows start closing automatically after the key is removed and the driver's door is closed post-ignition off; third, the windows start closing automatically when the remote control is pressed after the ignition is turned off and the door is closed.
4
4
Share

Is ETC one card per vehicle?

ETC is one card per vehicle, and one card can be bound to multiple vehicles. According to the "Rules for the Use of Non-stop Express Pass System," when applying for an ETC card, you need to fill out the "ETC Business Deduction Authorization Form," where you can specify multiple vehicles for payment binding. This means there is no limit on the number of vehicles that can be bound to a single ETC card for payment purposes. ETC is a non-stop electronic toll collection system, also known as an automatic road toll system. It is specifically designed for toll roads and is commonly used on highways, toll bridges or tunnels, and certain urban road sections to alleviate traffic congestion. ETC Deduction Principle: Highways have one or more ETC lanes. Through microwave short-range communication between the onboard electronic tag installed on the vehicle's windshield and the microwave antenna in the ETC lane at toll stations, the system uses computer networking technology to settle payments with banks. This allows vehicles to pass through toll stations without stopping, based on the principle of "pass first, deduct later." Benefits of Installing ETC: Time-saving: Eliminates the hassle of waiting in queues; Green and eco-friendly: Reduces noise and exhaust emissions by enabling vehicles to pass toll stations without stopping, thus lowering pollution; Reduced wear and tear: Saves costs by minimizing frequent starts and stops, reducing vehicle wear and fuel consumption; Improved efficiency: ETC lanes can theoretically increase traffic flow efficiency by 2-3 times, making traditional ETC faster, more advanced, and more high-tech. Compared to license plate payment, ETC technology is more mature and advantageous. More policy support: The State Council explicitly stated in the "13th Five-Year Plan for the Development of a Modern Comprehensive Transportation System" that "by 2020, the interoperability of transportation cards in key city clusters will be basically achieved, and the proportion of vehicles equipped with ETC will significantly increase." The plan also sets a target of "achieving a 50% ETC usage rate for road passenger vehicles by 2020" in the main indicators of comprehensive transportation development during the "13th Five-Year" period. More future possibilities: In addition to continuously improving the convenience of ETC installation and usage rates for passenger vehicles, efforts will be made to promote ETC usage for trucks and explore deeper integration of ETC systems with vehicle-to-vehicle communication, vehicle-to-infrastructure coordination, and other smart transportation initiatives. This will provide comprehensive travel services for vehicle owners, meaning more application scenarios will support ETC usage.
10
1
Share

What is the tire size of the Sail 3?

The tire size of the Sail 3 is 175/70R14. The first number, 175, represents the tire width of 175MM. The 70 indicates that the tire's aspect ratio is 70%, meaning the section height is 70% of the width. The 14 represents the rim diameter of 14 inches, and the letter "R" in the middle stands for radial tire. The Sail 3 comes standard with 14-inch aluminum alloy wheels, featuring an 8-spoke design that is quite durable. It is equipped with Giti Comfort-220 series tires, which are low rolling resistance tires emphasizing economy. The spare tire is non-full-size and is from the Chaoyang tire brand. If you want to replace the tires yourself, you can follow these steps: Retrieve the spare tire and jack, place the jack under the vehicle frame near the tire to be replaced, ensuring the jack touches the metal part of the frame; Raise the jack until it supports the car. The jack should be positioned under the vehicle, and check to ensure it is at a right angle to the ground; Remove the hubcap and loosen the nuts counterclockwise. Do not completely unscrew the nuts; just loosen them enough to eliminate resistance. When loosening the nuts for the first time, keeping the tire on the ground ensures that the nuts turn rather than the tire; Turn the nuts counterclockwise until they are loose. Repeat this step for all lug nuts and remove them completely; Place the new tire on the wheel hub, carefully aligning the tire rim with the wheel bolts. Install the lug nuts and hand-tighten them until all nuts are snug. The tire replacement is now complete. In addition to the model, the following common data is marked on the tire: Tire cord material: Indicated by Chinese pinyin, such as M for cotton cord, R for rayon cord, N for nylon cord, G for steel cord, and ZG for steel radial cord tire. Speed rating: Indicates the maximum speed at which the tire can carry a specified load under defined conditions. Letters A to Z represent the certified speed ratings from 4.8km/h to 300km/h. Common speed ratings include: Q: 160km/h; H: 210km/h; V: 240km/h; W: 270km/h; Y: 300km/h; Rim specification: Indicates the rim size compatible with the tire for practical use, such as "Standard Rim 5.00F".
8
2
Share

What should be noted for the first maintenance of Volkswagen cars?

Items to bring for the first maintenance include: driver's license; maintenance manual; warranty manual; owner's ID card; vehicle registration certificate; vehicle purchase invoice, and take the vehicle to the designated first maintenance facility. Important note: Make an appointment with the 4S shop in advance. The first maintenance refers to the initial service after a new car has been driven, with the specific timing varying by vehicle, generally after driving 3,000~5,000 kilometers or about half a year. It is essential to attend the first maintenance on time, neither early nor delayed. The completion of the first maintenance marks the end of the car's break-in period, allowing it to be driven under standard load and normal speed as required by the vehicle. The timing of the first maintenance is calculated from the date of vehicle pickup. There are two indicator values for the first maintenance: mileage and time. Whichever comes first serves as the standard. The first maintenance items include: changing the engine oil and oil filter, cleaning the air filter, checking various fluid levels for normalcy, inspecting the generator belt and wiper blades for damage, checking tire pressure for normalcy, and examining tires for damage or bulges. Required time: Completing all tasks takes approximately 2 hours. The most crucial aspect of the first maintenance for a new car is changing the engine oil and oil filter. When changing the oil, the oil filter must also be replaced. The choice of oil must refer to the "Vehicle Use and Maintenance Manual," as different vehicle models specify different oil grades. Maintenance precautions: Do not rinse the interior of the car body with water: Many people clean their cars themselves during holidays, washing the body with water and scrubbing with a cloth. Here, it is important to note that the interior of the car body should not be directly washed with water. If the floor mats are dirty, they can be vacuumed or taken out, scrubbed with a brush and detergent, dried, and then put back. There are many holes under the rubber mats on the floor of the driver's compartment. Water entering these holes will not dry out but will flow through the holes to areas like the gearbox, causing erosion and corrosion. A better approach is to clean with a vacuum cleaner and then wipe with a cloth to prevent water accumulation. Do not mix different brands of antifreeze: When the antifreeze in the car is low, it is recommended to drain the antifreeze and add the same brand from the beginning. Since antifreeze brands differ, their chemical properties vary greatly. Various functional additives can corrode others. Different brands of antifreeze use different additives, so they should not be mixed to avoid unnecessary trouble. Do not lubricate tire bolts and nuts: When the bolts on a moving car rust, they are often oiled to function properly again. To prevent the bolts and nuts on the wheels from rusting, some people apply lubricant to them, but this introduces potential safety hazards. When the car is driven at high speed, the bolts and nuts can easily loosen or even fall off, leading to driving malfunctions. Do not press the accelerator when starting an EFI car: The starter of an EFI car is different from that of a regular car. Its fuel injection control device can automatically adjust the fuel supply based on the starter's temperature and operating conditions, ensuring a smooth start.
6
3
Share

Is it necessary to add antifreeze in summer?

Antifreeze also needs to be added in summer. More information about antifreeze is as follows: 1. Antifreeze evaporates quickly in summer, so it is necessary to frequently check whether the antifreeze is insufficient. If it is insufficient, it should be replenished with the same brand of antifreeze in time. Do not replenish with antifreeze of other brands or water. 2. Antifreeze is the main working medium in the car engine cooling system. Its main function is to keep the engine at a suitable working temperature through forced circulation in the cooling system. 3. In addition to its antifreeze effect, antifreeze formulated with chemical components such as ethylene glycol not only has excellent low-temperature resistance but also has particularly good high-temperature resistance.
13
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.