Where is the OBD interface on the X-Trail?

1 Answers
McAbel
07/29/25 11:24pm
The OBD interface of the X-Trail is located below the steering wheel, slightly towards the driver's side, about 5cm to the right of the fuse box, facing downward. You'll need to position your head close to the foot mat to see it. OBD stands for On-Board Diagnostics, which translates to the vehicle's onboard self-diagnosis system in Chinese. More detailed information is as follows: 1. This system can monitor the working conditions of the engine's electronic control system and other functional modules of the vehicle in real-time during operation. If any abnormal conditions are detected, it identifies specific faults based on specific algorithms and stores them in the system's memory in the form of Diagnostic Trouble Codes (DTC). 2. The useful information obtained from the system's self-diagnosis can assist in vehicle maintenance and repair. Technicians can use the vehicle's original specialized equipment to read the fault codes, enabling quick fault localization for vehicle repairs and reducing manual diagnosis time.
Was this review help?
2
4
Share
More Forum Discussions

What is the reason for the abnormal noise in the Geely Emgrand clutch pedal?

Geely Emgrand clutch pedal abnormal noise is mainly caused by damaged car parts, such as the return spring of the release bearing being damaged, loose bearings or rivets, or broken steel plates. When the engine is idling and the clutch is released, abnormal noise occurs. If the clutch returns normally, check whether the gap between the release bearing and the release lever meets the regulations and adjust it accordingly; if the clutch cannot return normally, it indicates that the return spring of the release bearing is damaged and needs to be replaced in time. When the engine is idling and the clutch is pressed, abnormal noise occurs, indicating that the bearing is damaged, the bearing balls are broken, or there is a lack of oil causing burning, and it needs to be replaced or repaired in time. When the car starts and the pedal is just released, abnormal noise indicates that the rivets of the driven plate and the spline shaft sleeve are loose or the steel plate is broken. If there is a single impact sound when the clutch is engaged, it is generally due to the loose fit between the driven plate spline shaft sleeve and the transmission first shaft; if the driven plate has a damper, it may be due to the broken damper spring. Tighten the loose rivets or replace the broken steel plate.
2
2
Share

How to Determine the Soot Loading of a Diesel Vehicle's DPF?

A calculation method for soot loading in diesel engine DPFs based on pressure drop, which includes parameters such as exhaust temperature before the DPF and exhaust temperature after the DPF. The most direct method to determine the soot loading of a DPF is to weigh the DPF both unloaded and after loading.
11
0
Share

How to Deal with Pungent and Irritating Exhaust from Diesel Vehicles?

Consider whether the fuel injection volume in the cylinders is sufficient, as carbon deposits may cause partial blockage or improper adjustment of the fuel injectors. You can add a cleaning agent to the fuel. Insufficient air intake for combustion. You can add a cleaning agent to the fuel and a repair agent to the lubricating oil. Add a cleaning and emission-reducing agent to the fuel and a repair agent to the lubricating oil. Adjust the fuel injection pump appropriately.
12
0
Share

How to Read the Speed on a Car Dashboard?

Generally, a car's odometer consists of two parts: a speedometer and a trip meter. The speedometer indicates the speed in kilometers per hour. The numbers displayed on the odometer represent the total kilometers the car has traveled since it left the factory. To measure the distance between two points while driving, you can refer to the trip meter. A small button is used to reset the trip distance, but the total mileage cannot be cleared.
12
0
Share

How to Deal with Oil and Grease Stains on Car Surfaces?

If the car has not been stained for long, you can use rhinoceros clay to wash the car, which makes it very easy to remove. Generally, performing a glaze sealing treatment once will make the car paint clean and bright. Small stains that are usually hard to wash off and minor scratches caused by sand and stones on the car paint will be cleaned away. If the corrosion has reached the paint surface, a repainting solution is necessary.
20
1
Share

What is the emission standard for the 2018 Magotan?

The 2018 Magotan models all comply with the China V emission standard. Starting from 2019, many cities and regions in China began implementing the China VI emission standard. The Magotan is a mid-size sedan under the Volkswagen brand, with dimensions of 4866mm in length, 1832mm in width, and 1464mm in height, and a wheelbase of 2871mm. The Magotan is equipped with three types of engines: a 1.4-liter turbocharged engine, a low-power version of the 2.0-liter turbocharged engine, and a high-power version of the 2.0-liter turbocharged engine. The 1.4-liter turbocharged engine is paired with a 7-speed DSG transmission, while the 2.0-liter turbocharged engine models come with a 6-speed DSG transmission.
2
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.