Where is the OBD interface located on the Haval H6?

What are the maximum and minimum speed limits on a four-lane highway?

If driving on a four-lane highway, the speed division for vehicles is as follows: when in the leftmost lane, the speed should be between 110 km/h to 120 km/h; when driving in the second or third lane, the speed should be between 90 km/h to 110 km/h; when driving in the rightmost lane, the speed can be below 90 km/h but not lower than 60 km/h. Below is more detailed information: 1. For a three-lane road in the same direction, when a vehicle is in the leftmost lane, the speed should be between 110 km/h to 120 km/h, which is considered the overtaking lane; 2. When driving in the middle lane, the speed should be between 90 km/h to 110 km/h, which is the standard driving lane; 3. When driving in the right lane, the speed should be between 60 km/h to 100 km/h, typically designated for trucks; 4. The rightmost emergency lane should not be entered unless there is an emergency.

16

1

Share

Why Do Large Vehicles Need to Add Water?

Adding water to large vehicles helps in cooling the engine. Below is an introduction to the engine cooling system: 1. Introduction: The function of the automobile cooling system is to dissipate part of the heat absorbed by heated components in a timely manner, ensuring the engine operates at the most suitable temperature. The engine cooling system can be divided into air cooling and water cooling. A cooling system that uses air as the cooling medium is called an air-cooled system, while one that uses coolant as the cooling medium is called a water-cooled system. 2. Cooling System Circulation: (1) Main Circulation: The main circulation includes two working cycles, namely the "cold engine cycle" and the "normal cycle". (2) Heating Circulation: The coolant passes through the heating device inside the vehicle, transferring the heat from the coolant into the vehicle, and then returns to the engine.

19

5

Share

What is the maximum power of a 48V motor?

48V motors have a maximum power of 400W. The maintenance methods for motors are as follows: 1. Inspection and maintenance of bearings: After a period of use, bearings should be cleaned and the grease or lubricating oil replaced. The timing for cleaning and oil replacement depends on the motor's working conditions, environment, cleanliness, and type of lubricant. Generally, cleaning and grease replacement should be performed every 3-6 months. Motors operating at higher oil temperatures or in poor environmental conditions with more dust require more frequent cleaning and oil changes. 2. Insulation inspection: The insulation capability of insulating materials varies with their dryness, so checking the dryness of motor windings is crucial. Factors such as a humid working environment or the presence of corrosive gases can damage electrical insulation. The most common issue is winding grounding faults, where insulation damage causes live parts to come into contact with metal parts like the motor casing that should not be live. Such faults not only affect the motor's normal operation but also pose safety hazards. Therefore, during motor use, insulation resistance should be regularly checked, and it's important to ensure that the motor casing is reliably grounded.

7

3

Share

Where is the spare tire placed in the Corolla Hybrid?

Corolla Hybrid is the first model under the FAW Toyota brand equipped with domestically produced hybrid technology. The spare tire of the Corolla Hybrid is placed under the trunk floor. Due to the influence of the battery pack, the interior space of the trunk is slightly reduced compared to the regular version, but it is sufficient for daily needs. Information about the spare tire is as follows: 1. Spare tires are generally divided into full-size spare tires and non-full-size spare tires. The width of a full-size spare tire is the same as that of a normal tire; the width of a non-full-size spare tire is smaller than that of a normal tire, and its speed rating is much lower than that of a normal tire. 2. When installing the spare tire, make sure to tighten all the tire fixing screws before removing the jack; when tightening the screws, follow the diagonal sequence, and do not tighten them in a clockwise or counterclockwise order.

17

5

Share

Can an Uncovered Brake Fluid Cap Cause Brake Failure?

An uncovered brake fluid cap may potentially cause brake failure. Brake failure can result from excessive impurities in the brake master cylinder, poor sealing, vacuum booster failure, contaminated brake fluid or the formation of vapor lock due to mixing different types of brake fluid under heat, leakage in the brake master cylinder or wheel cylinders, or air leaks in the air reservoir or pipeline connections. Below are the specific impacts of not replacing brake fluid over an extended period: 1. Corrosion of the Braking System: Brake fluid is inherently hygroscopic and prone to absorbing moisture. If not replaced for a long time, the brake fluid can corrode the braking system, posing significant safety hazards. 2. Formation of Brake Vapor Lock: The boiling point of brake fluid decreases after absorbing moisture, which can lead to insufficient brake pressure and affect braking performance. When the temperature rises to the boiling point, the moisture in the brake fluid will vaporize, creating numerous air bubbles. 3. Clogging of the Brake System: Prolonged failure to replace brake fluid allows deposits and impurities in the brake lines to cause brake system malfunctions, impairing braking performance.

19

2

Share

What is the reason for the Nissan Sylphy remote control not responding when pressed?

Nissan Sylphy remote key failure is usually caused by the battery running low. You can split the remote key along the middle seam and replace it with a new battery. If that doesn't work, try re-matching the remote. Since smart keys use low-intensity radio waves, they may not function properly in the presence of magnetic interference. Frequently placing the smart car key and mobile phone together will inevitably cause the smart car key to malfunction. The basic components of a remote key are as follows: 1. Transmitter: Composed of a transmission switch, transmission antenna, integrated circuit, etc., containing an identification code storage circuit and an amplitude modulation circuit, with a button-type lithium battery on the opposite side of the circuit. The transmission frequency uses radio waves, and pressing the transmission switch button once sends a signal. 2. Receiver: After the transmitter sends the identification code using shortwave modulation, it is received by the car's shortwave antenna and enters the shortwave high-frequency amplification processor of the receiver's electronic control unit through a distributor for demodulation, where it is compared with the demodulator's identification code.

2

1

Share

Where is the OBD interface located on the Haval H6?

What are the maximum and minimum speed limits on a four-lane highway?

Why Do Large Vehicles Need to Add Water?

What is the maximum power of a 48V motor?

Where is the spare tire placed in the Corolla Hybrid?

Can an Uncovered Brake Fluid Cap Cause Brake Failure?

What is the reason for the Nissan Sylphy remote control not responding when pressed?

What does the 48V Light Hybrid System mean?

What Symptoms Occur When Brake Pads Have Problems?

What does the SS indicator on the car dashboard mean?

How long does idling take to fully charge the car battery?