Where is the OBD interface located on the Excelle?

1 Answers
DeEmmanuel
07/30/25 8:12am
The OBD interface of the Excelle is located behind the coin box on the driver's side. OBD stands for On-Board Diagnostics. The Excelle is a compact sedan under the Buick brand, equipped with a 1.3-liter naturally aspirated engine across all models. This engine is a three-cylinder unit with a maximum power output of 79 kW, a maximum torque of 133 Nm, and a maximum power speed of 6,200 rpm. The Buick Excelle has body dimensions of 4,468 mm in length, 1,765 mm in width, and 1,469 mm in height, with a wheelbase of 2,611 mm. It features a dual-injection engine and a fuel tank capacity of 40 liters. In terms of safety, the Buick Excelle is equipped with six airbags, including front dual airbags, front side airbags, and side curtain airbags.
Was this review help?
10
2
Share
More Forum Discussions

Why is the Nissan Qashqai not accelerating when pressing the accelerator?

The reason why the Nissan Qashqai is not accelerating when pressing the accelerator is due to clutch slippage. Below are the specific details: 1. Manifestation: Clutch slippage mainly manifests as the vehicle's speed not increasing with the rise in engine RPM during acceleration, resulting in the engine's power not being fully transmitted to the drive wheels, causing weak driving performance, especially noticeable when going uphill. 2. Causes: The main reasons for clutch slippage include insufficient friction of the clutch friction plate; shifting gears too early or disengaging gears before the clutch is fully engaged; prolonged driving with the clutch partially engaged or coasting with the clutch pedal depressed; and abnormal wear of the clutch plate caused by abruptly pressing the accelerator when the gear is not fully engaged or disengaged.
8
5
Share

What are the reasons for not being able to engage reverse gear in a manual transmission?

Manual transmission cars may fail to engage reverse gear due to the following reasons: 1. Internal gear lever malfunction: The gear lever assembly may have internal faults, such as worn-out gears inside the lever, causing it to get stuck. This makes it difficult to move the lever back and forth, resulting in failure or difficulty in gear engagement. 2. P-gear solenoid valve failure: The P-gear lock solenoid valve inside the gear lever or the brake switch may be faulty. For safety reasons, to prevent accidental engagement of other gears when starting the vehicle, this P-gear solenoid valve is installed. It requires a signal from the brake pedal to release. 3. Incomplete clutch disengagement: This could be caused by faults in the clutch disc or pressure plate. Generally, replacing the clutch three-piece set, including the friction disc, pressure plate, and release bearing, is necessary.
1
5
Share

What is BYD's production volume?

In 2020, BYD's passenger car production reached 157,402 units, an increase of 31,582 units compared to 2019, representing a year-on-year growth of 25.1%. Below is relevant information about BYD: 1. Brand History: BYD Company Limited was founded in 1995, starting with a team of over 20 people. By 2003, it had grown into the world's second-largest rechargeable battery manufacturer and established BYD Auto in the same year. Starting as a battery manufacturer, BYD's venture into automobile production initially positioned it as an 'outsider' in the field. However, leveraging its 'independent intellectual property rights' and the acquisition of Qinchuan Automobile, BYD gained a first-mover advantage over other newcomers. 2. Brand Introduction: BYD Auto adheres to a development path of independent R&D, production, and branding, committed to creating truly affordable and high-quality vehicles for the public. The product designs incorporate advanced international trends while aligning with the aesthetic values of Chinese culture.
15
5
Share

What to Do If a Motorcycle Insurance Policy Is Lost? Where Can I Check?

Motorcycle insurance policy can be reissued if lost. The specific information is as follows: 1. Electronic policy: Contact the insurance company to resend a new electronic policy. 2. Paper policy: Report the loss and apply for a reissue. The methods for inquiry are as follows: 1. Insurance company inquiry: Use your ID card to inquire at the insurance company. 2. Telephone inquiry: Call the insurance company's customer service hotline to inquire. 3. Online inquiry: 1. Directly search online by entering the name of your insurance company followed by "auto insurance"; 2. After opening the auto insurance page of PICC, look for the policy inquiry section; 3. Then enter the license plate number and the policyholder's ID number to inquire.
13
4
Share

What is the recommended tire pressure for family sedans?

For sedan tires, it is generally recommended to inflate them to 240kPa=2.4Bar, which is commonly referred to as 2.4 pressure. Additional information is as follows: Tire pressure: Air pressure is the lifeline of a tire, and both excessive and insufficient pressure will shorten its service life. Insufficient pressure will increase the tire's contact area with the ground, accelerating wear on the tire shoulders. Excessive pressure will cause excessive stretching and deformation of the tire cords, reducing the elasticity of the tire body and increasing the load on the car while driving. If subjected to impact, it may lead to internal cracks and blowouts. Additionally, excessive pressure accelerates wear on the tire tread and reduces its resistance to punctures. A tire pressure gauge can accurately measure the tire's air pressure, allowing continuous monitoring to ensure driving safety. When a tire is subjected to prolonged high pressure, common issues include: uneven wear on the center of the tread, affecting the tire's lifespan. Once the pressure returns to normal, the center contact area may lift off the ground, drastically increasing the risk factor, exceeding the stress limit of the internal cord wires, leading to cord breakage and blowouts, as well as difficulties in steering control and limited traction.
12
4
Share

Is It Harmful to Leave a Car with a Flat Tire Overnight?

Leaving a car with a flat tire overnight will not cause harm. As long as the vehicle is not moved, a flat tire will not damage the wheel rims. Every car's suspension is designed to handle a certain amount of drop, and the thickness of the tire will prevent damage to the suspension. It is best to call a professional tire service to help replace the tire and inspect it. The following are relevant details: 1. Check Tire Pressure: First, determine the tire pressure, roughly how much it is. Whether it is completely flat or just slowly losing air. Cars with built-in electronic devices can directly measure tire pressure. The simplest method is to step on the tire with your foot. If there is some give, it means you can still drive a short distance to the repair shop. Note that the speed should not be too high, not exceeding 60 kilometers per hour, and avoid sudden braking. It is best to drive slowly along the far right side of the road to the repair shop. 2. Replace the Spare Tire: If stepping on the tire yields no response and it remains completely flat, and the situation is severe, then you should not continue driving. You need to replace it with the spare tire. The trunk of the car contains the necessary tools, including a jack and the required wrench to remove the bolts. The location of the spare tire varies by car model but is generally easy to find, usually under the trunk or in a more visible spot. After replacing the spare tire, go to the repair shop as soon as possible to replace it with a normal tire.
17
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.