Where is the Nissan Sunny OBD interface located?

2 Answers
ZoeAnn
07/24/25 12:03am
The OBD interface of the Nissan Sunny is located under the steering wheel cover. Here is some information about the OBD system: 1. OBD is a detection system extended for automotive fault diagnosis. 2. The OBD system continuously monitors the engine's operating conditions to check if the vehicle's exhaust exceeds the standard. If it does, it will immediately issue a warning. Additional information: 1. Exterior design. The Sunny inherits Nissan's family-oriented design approach, with a rounded and full front-end design; the body lines are smooth, making the overall appearance more balanced and practical. 2. Handling. The Sunny's engine features an EFI dual-mode dual-hole multi-point fuel injection system, which can provide precise and appropriate fuel injection according to different road conditions and engine load levels. Therefore, it offers more reliable mixture ratios and responsiveness compared to general electronic fuel injection systems.
Was this review help?
8
5
Share
SanJameson
08/10/25 7:52pm
I encountered this when repairing my car before. The OBD port of the Nissan Sunny is quite easy to find—it's hidden in a small recess on the left side under the steering wheel. Just lift the plastic cover, and you'll see a rectangular 16-pin port. I suggest you feel around slowly in a well-lit area and avoid pulling the cover forcefully to prevent breaking the clips. Speaking of the OBD port's function, it's a real game-changer. Connecting a diagnostic tool allows you to read engine fault codes and emission data in real-time, helping you identify issues promptly during inspections or when warning lights come on. For example, I often use it to monitor fuel consumption changes, which saves a lot on maintenance costs. Remember to ensure the engine is off before operating and avoid using counterfeit tools for plugging/unplugging to prevent short circuits and damage to the electronic system. In short, the location is fixed but not obvious—practice makes perfect with a bit more attention.
Was this review help?
1
4
Share
Expand All
More Forum Discussions

How to reset the tire pressure warning light on Changan CS15?

Method to reset the tire pressure warning light on Changan CS15: First confirm the tire pressure data is correct, then press and hold the button with an exclamation mark symbol on the gear lever side for 3 seconds until you hear a prompt sound from the instrument panel, indicating successful reset. Reasons for the tire pressure warning light illumination: 1. Tire puncture triggering the TPMS light; 2. Sometimes caused by excessive tire pressure; 3. Prolonged driving with low tire pressure; 4. Tire pressure drop due to long-term lack of inflation. The Changan CS15 is a compact SUV under Changan Auto, featuring a black interior style with red accents on the center console, seats, door panels, and gear lever, complemented by silver decorations on the steering wheel and air vents, presenting a sporty overall appearance.
5
0
Share

What does SN mean in engine oil?

Engine oil SN represents the highest grade of engine oil, which is classified using a two-letter combination. The 'S' series denotes oils for gasoline engines, with specifications generally ranging from SA to SN. Each subsequent letter indicates improved performance over the previous grade, containing more additives to protect the engine. The further the letter is in the alphabet, the higher the quality grade. Most international brands offer engine oils at SF grade or above. Characteristics of engine oil: 1. Lubricity: The ability of engine oil to reduce friction, minimize wear, and prevent metal sintering under various conditions is called lubricity; 2. Low-temperature operability: The performance of engine oil to ensure easy starting and reliable oil supply in low-temperature conditions is called low-temperature operability; 3. Viscosity-temperature characteristics: The property of lubricating oil to change viscosity with temperature fluctuations is called viscosity-temperature characteristics.
13
5
Share

Why Does Fuel Consumption Increase After Throttle Body Cleaning?

The reason for increased fuel consumption after throttle body cleaning: After cleaning, the throttle body must undergo a re-adaptation process with the ECU to ensure normal engine operation. Once the adaptation is complete, the phenomena of increased fuel consumption and higher RPM will disappear. Due to prolonged lack of cleaning, excessive wear occurs between the throttle valve and throttle arm. After cleaning, the gap actually becomes larger, leading to higher fuel consumption. If the necessary adaptation procedures aren't performed after cleaning, the ECU continues calculating fuel injection based on the old throttle body parameters. Normally, after driving for some time, the vehicle will gradually adapt and fuel consumption will return to normal.
11
4
Share

How to Reset the Tire Pressure on GAC Mitsubishi Outlander?

The method to reset the tire pressure on GAC Mitsubishi Outlander: First, turn on the instrument power, then press and hold the reset button until the low tire pressure warning light goes off. Press and hold the reset button again until the low tire pressure warning light flashes three times and then goes off. During normal driving, if the tire pressure of a certain tire is low, the straight-line rotation speed of that wheel will increase. When the speed difference with other wheels reaches a certain value, the low tire pressure warning light will illuminate. The GAC Mitsubishi Outlander is positioned as a compact SUV, with a body length of 4705mm, width of 1810mm, height of 1680mm, and a wheelbase of 2670mm.
13
3
Share

What Causes Water Dripping from a Car's Exhaust Pipe?

Water dripping from a car's exhaust pipe is caused by water vapor present in the engine exhaust. When the water vapor encounters cold temperatures, it condenses into small water droplets, which accumulate in the exhaust pipe and are expelled during acceleration due to the exhaust's momentum. If there is excessive water in the exhaust pipe, it can damage the oxygen sensor of the catalytic converter. Additionally, the heat generated by the engine's combustion is mostly contained within the cylinders, with only a small amount escaping into the exhaust system, indicating stable engine power output. The condition of the engine can be reflected by the exhaust emissions. During operation, the engine temperature can reach between 400 to 800 degrees Celsius. The water vapor produced during combustion exits the engine into the exhaust pipe, where it condenses in cooler environments, gradually accumulating and forming small water droplets that drip from the exhaust outlet. In fact, water dripping from the exhaust pipe is a sign that the engine is in good condition, the fuel is burning efficiently, the fuel supply system is functioning well, and there is no cylinder wear.
12
3
Share

What is the battery capacity of the Zotye E200?

Zotye E200 battery capacity is 32KWH. Battery capacity is one of the important performance indicators to measure battery performance, which represents the amount of electricity discharged by the battery under certain conditions, that is, the capacity of the battery. Battery capacity is divided into actual capacity, theoretical capacity and rated capacity according to different conditions. The Zotye E200 is a microcar under the Zotye brand. The car has a length, width and height of 2735mm, 1600mm, and 1630mm respectively, with a wheelbase of 1810mm. The Zotye E200 is equipped with a permanent magnet synchronous motor, with a maximum power of 60KW and a maximum torque of 180Nm. The motor is powered by a ternary lithium battery.
14
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.