Where is the motorcycle starter located?

1 Answers
ElijahLee
07/30/25 12:36am
Motorcycle starter is located on top of the engine. Motorcycle starter working principle: The placement of the starter motor is primarily determined by the specific engine type and structure, with power transmitted to the crankshaft through the pneumatic motor. Maintenance methods are as follows: Turn on the vehicle's main switch and press the horn to check if the sound is loud. If the horn sounds loud, it indicates the battery, fuse, and charging system are functioning normally; otherwise, it suggests a malfunction. Next, inspect the starter relay. After operating the brake, press the starter button and listen for a "click" sound. If present, it means the starter button and relay are working properly. If absent, it indicates a fault in the starter button or relay, which should be checked and rectified individually using the short-circuit method for inspection.
Was this review help?
4
4
Share
More Forum Discussions

What is the process for the B2 Subject 3 driving test?

The process and tips for the B2 Subject 3 driving test are as follows: 1. Pre-start vehicle inspection: Prepare inside the vehicle (adjusting seats, mirrors, etc.). In these steps, it's crucial not to forget to fasten the seatbelt. The seatbelt buckle has two connectors—find the one with wires. Quickly adjust your mindset during these steps. 2. Starting the vehicle: Once prepared, the examiner will activate the test software. Follow the voice commands. When starting, ensure to signal, honk, and check mirrors. Different clutches may feel different, so you can use the throttle to start and gradually release the clutch once the car moves. 3. Road driving: This includes gear shifting, straight-line driving, turning, U-turns, and lane changes. These tasks are relatively simple but require attention to actual road conditions. Temporary stops are allowed. 4. Overtaking: Usually prompted by the computer, often when there's no vehicle ahead. Focus on executing the overtaking steps correctly. 5. Intersections, schools, bus stops, etc.: The main task here is to slow down before reaching an intersection and check for oncoming traffic or traffic lights. Drive according to the actual situation. Note that stopping at intersections is not allowed. 6. Night driving: Some locations simulate this before departure, while others conduct it as a live test at night. Essentially, it repeats the above tasks with added light operations. 7. Pulling over: Once all tasks are completed, the examiner will instruct you to pull over.
13
3
Share

How to Remove the Car Battery?

The steps to remove the car battery are as follows: 1. Loosen the negative terminal nut, open the two fastening buttons of the insulation cover, and you will see the red and black insulation covers on the positive and negative terminals. Flip open the insulation covers to reveal the locking nuts; 2. Remove the negative terminal. Use a wrench or hex socket to loosen the fastening nut of the negative terminal, then gently pry open the fastening block with a flat-head screwdriver, and then pull out the negative terminal; 3. Remove the positive terminal. Use the same method to remove the positive terminal; 4. Remove the locking strap. Unscrew the nut that secures the battery's locking strap, loosen the strap, and then remove the battery; 5. When installing a new battery, simply follow the reverse steps. However, it is important to note that when connecting the terminals, the order is 'positive first, then negative,' which is the opposite of the removal process. The principle remains the same—to prevent short-circuit hazards and ensure safety.
1
3
Share

How to Correct Steering Wheel Timing When Reversing into a Parking Space?

The correction mantra for reversing too early or too late is: if you turn too early and the right side is narrow, turn the wheel left to adjust; if you turn too late and the left side is narrow, keep the wheel turned fully right. Additionally, it's crucial to control the vehicle speed using the clutch, as only a sufficiently low speed allows enough time for corrections. When checking the rearview mirrors, you don't necessarily need to sit upright; slightly leaning your head forward can help accurately observe the position between the car body and the parking corner. Below are the correction methods for steering wheel timing when reversing into a parking space: 1. Turning too early: If the distance between the car body and the right front corner of the parking space is less than 30 cm, you can turn the wheel back half a turn if it's slightly less than 30 cm; if you're about to hit the corner, straighten the wheel. 2. Observing through the left and right rearview mirrors: Monitor the position between the car body and the side lines through the mirrors, and straighten the wheel when the car body is almost parallel to the lines.
11
5
Share

What is the minimum ground clearance of the Jetta?

The minimum ground clearance of the Jetta is 109mm. The Jetta is equipped with a MacPherson strut independent front suspension and a compound torsion beam non-independent rear suspension. Below is some information about vehicle ground clearance: 1. Ground clearance refers to the minimum height between the vehicle's chassis and the ground under maximum load conditions. 2. The minimum ground clearance reflects the vehicle's ability to pass over obstacles or uneven terrain without collision. Additional information: 1. A larger ground clearance makes it easier for a sedan to navigate various complex road surfaces, but stability is compromised when driving on highways. 2. If the ground clearance is less than 110mm, high-speed stability is improved, but passability is reduced.
10
3
Share

What is the range of the Taycan?

Taycan range-related data is as follows: 1. According to official data, the Porsche Taycan has a maximum range of over 465km, putting its power and range data in the same league as the Tesla Model-S. The Porsche Taycan is equipped with two permanent magnet synchronous motors, one for the front axle and another to drive the rear wheels, delivering a combined output of over 600 horsepower. These two motors are powered by a high-voltage lithium-ion battery, achieving a range of 465 kilometers. 2. The Taycan's range is influenced by actual driving conditions, and the practical range may be lower. The 465 kilometers is the result tested under ideal conditions.
4
0
Share

What are the main items included in car modification?

In general, car modifications mainly include the power system, chassis upgrades, control systems, exterior and interior modifications, among others. There are more than a dozen items allowed for modification, which are sufficient for ordinary car enthusiasts. It is recommended to stay at the decorative level because performance upgrades will always change various parameters of the original car, more or less damaging the frame and suspension. Engine modifications: intake system, exhaust system, fuel supply system, crankshaft and connecting rod mechanism, valve train, compression ratio, turbocharging system, etc. Chassis modifications: braking system, tires, rims and wheel covers, suspension, anti-roll bars, etc. Electrical equipment modifications: ignition system, headlights, signal lights, decorative lights, etc. Body modifications: body kits, sunroofs, spoilers, stickers, etc. Interior modifications: trim panels, seats, car appliances (water dispensers, refrigerators, microwaves), etc. Safety device modifications: anti-theft devices, reverse radar, safety warning systems, etc. Entertainment and information system modifications: audio systems, car hands-free kits, walkie-talkies, car GPS, car black boxes, etc. Off-road vehicle modifications: protective bars, roll cages, off-road tires, off-road lights, winches, etc. Generally, upgrading the power starts with the exhaust pipe, in the order of the tail section, mid-tail section, and full section. If the full section is replaced, it usually requires upgrading the computer program as well, and of course, upgrading the catalytic converter. Then comes the intake system, which can be replaced with a "mushroom head" that allows more air intake. Major manufacturers' accessories also include vehicle-specific intake air deflectors. Additionally, you can add or replace intercoolers, oil coolers, blow-off valves, etc. For higher requirements, you can replace the turbocharger, expand the cylinder, etc. From the simplest addition of reinforcement parts to upgrading stabilizer bars, wheels, tires, and then replacing shock absorbers, brakes, etc. The first step in chassis modification should start with choosing a suitable good tire. Tire modifications are nothing more than widening, reducing the aspect ratio, and changing the tire material. Unless there is a significant increase in horsepower, simply widening the tires by 10~20mm is usually enough to handle more aggressive driving on general roads without changing the steering characteristics and suspension load. The fastest and simplest way to change the car's appearance is to add aerodynamic kits. The so-called aerodynamic kits, commonly known as body kits, basically include the intake grille, side skirts, rear bumper, and rear spoiler (tail wing), etc. Good kits usually reduce the car's speed, making it perform more stably.
17
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.