Where is the Mercedes-Benz parking button?

1 Answers
LeBrady
09/08/25 4:08am
Mercedes-Benz's automatic parking system is built-in and does not have a button; it automatically activates once the engine is started. The introduction and working principle of the automatic parking function are as follows: Introduction to automatic parking: Automatic parking refers to a function that automatically applies the brakes. Once activated, for example, when stopping at a traffic light, there is no need to use the handbrake or electronic parking brake, simplifying operations. For automatic transmission models, it also eliminates the need for frequent shifting between D to N or D to P. Working principle of automatic parking: The automatic parking function uses a slope sensor to provide precise parking force through the controller. During startup, the parking control unit calculates information from sensors such as the clutch distance sensor, clutch engagement speed sensor, and throttle pedal sensor. When the driving force exceeds the running resistance, the parking brake is automatically released, allowing the car to start smoothly.
Was this review help?
14
1
Share
More Forum Discussions

What is the normal fuel consumption for the 10th-generation Civic?

The official combined fuel consumption for the 10th-generation Civic is 5.4-6 liters per 100 kilometers. Fuel consumption calculation formula: Fuel consumed ÷ Distance traveled × 100 = Fuel consumption per 100 kilometers. The data on fuel consumed is relatively difficult to obtain. Generally, a full tank is used as the initial data. After driving a certain distance, the tank is refilled to full, and the fuel amount provided by the gas station is taken as the accurate measurement. Tips to reduce fuel consumption: The economic speed is the speed at which the car consumes the least fuel when driving in direct drive or overdrive. When a car is driven on the same road, different speeds result in different fuel consumption. Therefore, there is a specific speed at which fuel consumption is the lowest. Thus, the car should be driven at a medium speed in direct drive or high gear to save fuel.
15
5
Share

Where is the OBD interface of Citroen C4L?

The OBD interface of the Citroen C4L is located in front of the car's gear lever, near the USB interface and the cigarette lighter. By touching with your hand, you will find a small hole. Hook it with your finger and open the cover to find the car's OBD interface inside. Here is the relevant introduction: 1. Definition of OBD: The full English name of OBD is On-Board-Diagnostic, which means on-board automatic diagnostic system in Chinese. This interface can connect to a diagnostic computer to read the car's fault codes. It is an important interface in the car, and you should also pay attention to protecting this interface during use. 2. Function of OBD: The on-board automatic diagnostic system constantly monitors the operating conditions of the engine and the working state of the exhaust after-treatment system. Once it detects a situation that may cause excessive emissions, it will immediately issue a warning. When a fault occurs in the system, the fault lamp (MIL) or Check Engine warning light will illuminate, and the OBD system will store the fault information in the memory. Relevant information can be read in the form of fault codes through standard diagnostic instruments and diagnostic interfaces. Based on the prompts of the fault codes, maintenance personnel can quickly and accurately determine the nature and location of the fault.
15
4
Share

Where to find the 16-inch wheel data for Lavida?

The 16-inch wheel data for Lavida is printed on the tire sidewall, with two representation methods, such as 34×7 or 7.50-20. Introduction to wheel data: Wheel size refers to the diameter of the wheel. For example, in 175/70R14, the number 14 represents the wheel diameter, which is also the wheel size. The wheel width, commonly known as the J value, directly affects tire selection. For the same tire size, different J values will require different tire aspect ratios and widths. Wheel maintenance cycle: Wheel bearings should be maintained every 50,000 to 80,000 kilometers and replaced at 100,000 kilometers. The condition of wheel bearings depends on factors such as the quality of the bearings themselves, driving conditions, mileage, and load capacity. Generally, automotive wheel bearings can last over 100,000 kilometers.
7
1
Share

How many tires should be replaced at once for a BMW 3 Series?

Replace according to the actual situation. Replace the severely worn or damaged tire. If all tires have exceeded their service life, replace them all. Tire service life: Under normal driving conditions, the lifespan of a tire is generally 60,000-80,000 kilometers, approximately 3-5 years. It can be calculated from the production date (marked on the side of the tire), and the aging replacement cycle is five years. If it exceeds five years, the tire should be replaced even if the tread wear does not reach the limit. Methods to determine tire wear: There are mainly two types of markings on a tire that help the owner determine the wear condition. One is the rectangular raised mark located at the bottom of the tread groove, usually used to judge the degree of tire wear, and the other is the triangular mark located on the shoulder on both sides of the tire, which clearly indicates the position of the wear indicator. The thickness of the tire wear indicator is about 1.6 millimeters, which is the legal minimum groove depth. When the tire wears to this mark, the owner should replace the tire immediately.
16
2
Share

What is the issue with the Haval H6 air conditioning turning on automatically?

The air conditioning was not turned off before parking the car; the air conditioning is set to automatic start mode; the air conditioning control switch, control computer, and its control circuit are abnormal. How car air conditioning works: When heating, the car air conditioning utilizes the residual heat of the coolant, and when cooling, it uses the phase change of the refrigerant. When the heating function of the car air conditioning is activated, the high-temperature coolant from the engine flows through the heater core, behind which there is a blower, allowing warm air to blow out from the air vents. Cooling is more complex: after pressing the AC button, the compressor clutch engages, the engine starts to drive the compressor, which continuously compresses the refrigerant. How to turn on the heating in car air conditioning: First, start the car. After the engine runs for a while and the coolant reaches normal temperature, you can turn on the car's heating. Rotate the temperature control knob to the red zone and adjust the fan speed switch.
1
0
Share

Where to Place the Jack for a Corolla?

If changing a spare tire, the jack should be placed under the raised position on the side of the chassis near the door sill. Ensure the jack is positioned straight to prevent tilting or slipping, then you can proceed to change the tire. Precautions for using a car jack: Do not place the jack under the bumper position, as this can easily cause damage to the car's bumper. When using the car jack, ensure there are no passengers remaining in the car to avoid the risk of the jack slipping during use, which poses significant safety hazards. Precautions for changing a car tire: Use the jack to slightly lift the car, then use a tire wrench to loosen the tire nuts. Do not remove them completely; wait until the tire is lifted off the ground before fully removing them. The direction to loosen the screws is towards the rear of the car. When supporting the chassis with the jack, there are usually position indicators for the support points. Make sure the support point is perpendicular to the ground surface to avoid instability and tipping. After removing the old tire and installing the new one, tighten the nuts in a diagonal sequence.
8
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.