···
Log in / Register

Where is the manual lock for the Fit?

4 Answers
McBrooklyn
07/23/25 8:14pm
Fit's manual lock is located at the OBD interface. Here is more information about the Fit: 1. The Fit is a compact car under Honda, equipped with a 1.5-liter naturally aspirated Earth Dreams engine. The 1.5-liter naturally aspirated engine of the Fit has a maximum power of 96 kW, a maximum torque of 155 Nm, a maximum power speed of 6600 rpm, and a maximum torque speed of 4600 rpm. This engine features i-VTEC technology and direct fuel injection, and uses an aluminum alloy cylinder head and block. The engine is paired with either a 5-speed manual transmission or a CVT. 2. The front suspension of the Fit uses a MacPherson strut independent suspension, while the rear suspension employs a torsion beam non-independent suspension.
Was this review help?
14
3
Share
DiEli
08/10/25 3:46pm
On the inside of the Fit's door, the manual door lock is usually located above or near the main driver's door handle, as a small knob or lever that can be pushed lightly to lock the door. I remember my first Fit was an older model, and that lock tab was designed very conveniently—just reach out and touch it. The new generation is the same, positioned right where your arm naturally rests. It's easy to find: sit in the car, look down at the inner side of the door handle, and there it is—that silver thing, operable without even bending over. If you can't find it right away, it might be because dust has accumulated from the door being open too long—just wipe it clean. Some friends think the car only has an automatic lock, but this manual lock is actually super practical—for example, when the electric system is out of power, using it to manually lock the door is safer. I recommend getting familiar with its feel to avoid fumbling in emergencies.
Was this review help?
20
5
Share
Expand All
SanMaya
09/23/25 3:09am
As a car owner, I often encounter beginners asking this question. The manual door lock for the Fit is located on the inner door panel, right next to the door handle. It's a small plastic or metal piece that's easy to flip. The position isn't complicated: look towards the center of the door panel, usually slightly higher up, and a slight twist will lock the door. If you still can't find it, try gently lifting the small lining under the window, as it might be tucked away snugly. This design is a safety measure to prevent accidental activation—unlike some people who frantically press buttons as soon as they get in the car, manual locks are more reliable. By the way: similar functions in all cars are placed this way for quick response; developing the habit of manually locking doors can help reduce battery drain issues.
Was this review help?
4
4
Share
Expand All
LeArya
11/06/25 5:25am
I think the manual lock position on the Fit is very clear, located directly on the inner side of the door near the handle. It's quite simple to operate: sit in the driver's seat, look down at the handle area, and there's just a small raised tab—pull it backward to lock. If the interior is too dark to see clearly, turn on the interior light first; it's not a big deal. Manual locks are crucial for safety—automatic systems can sometimes lag, and using the manual lock prevents doors from accidentally opening. This is especially reassuring during rainy days or when driving through tunnels. Don’t forget to check the door mats during inspections, as accumulated dust can cause jams; regular cleaning will prevent any issues.
Was this review help?
13
4
Share
Expand All
More Forum Discussions

What's the difference between maintenance done outside and at a 4S shop?

Differences between 4S shop maintenance and external maintenance: 1. Different risks: 4S shop maintenance has low risk and is guaranteed; external maintenance has high risk and no guarantee. 2. Different efficiency: 4S shop maintenance is less efficient but uses original parts; external maintenance is more efficient but does not use original parts. Benefits of 4S shop maintenance: 1. 4S shops can provide original parts and materials. 2. 4S shops can offer the most professional and reliable repair technology, professional equipment and tools, and focus on brand reputation. 3. 4S shops have a complete service process and post-repair service tracking system to ensure every repair procedure strictly follows the brand's requirements. 4. 4S shops have formal and open complaint channels and supervision systems, fully ensuring customer satisfaction. 5. 4S shops take responsibility for any disputes after repairs to guarantee your satisfaction.
9
2
Share

What is the label for fully synthetic engine oil?

Fully synthetic engine oil does not have a specific label, but the bottle will directly indicate "fully synthetic" on its exterior. The functions of fully synthetic engine oil are: 1. Between the piston and cylinder of the engine, as well as between the main shaft and bearings, there is rapid relative sliding. The oil forms a sufficiently thick oil film between the two sliding surfaces, separating the surfaces of the relatively sliding parts to reduce wear. 2. It carries heat back to the oil tank and dissipates it into the air, helping the radiator to cool the engine. 3. It cycles carbon deposits, sludge, and worn metal particles from engine parts back to the oil tank, using the flow of the lubricating oil to wash away contaminants generated on the working surfaces of the parts. 4. It provides shock absorption and cushioning. When the pressure at the engine cylinder port rises sharply, suddenly increasing the load on the piston, piston chips, connecting rod, and crankshaft bearings, the load is transmitted through the bearings' lubrication to cushion the impact load.
17
0
Share

What to Do If You Accidentally Fill a Car Requiring 95 Octane with 92 Octane?

If a car that requires 95 octane gasoline is accidentally filled with 92 octane, do not start the vehicle. Immediately contact a 4S shop or a maintenance technician to drain and clean the fuel tank and fuel lines, followed by a comprehensive engine inspection. The consequences of using 92 octane in a car designed for 95 octane include: 1. Reduced engine power. 2. Lower idle speed. 3. Increased fuel consumption. 4. Engine stalling or failure to start. Introduction to gasoline: 1. Gasoline is refined from various petroleum-derived components such as straight-run gasoline, catalytic cracking gasoline, and catalytic reforming gasoline, blended with high-octane components. 2. Gasoline is primarily used as fuel for spark-ignition internal combustion engines in automobiles.
15
0
Share

What Type of Engine Oil is Best for the First Car Maintenance?

Every vehicle comes with a manufacturer-recommended standard original engine oil. If not specifically specified, using the original engine oil is sufficient for both the first maintenance and subsequent regular services. Types of engine oil: Mineral Oil: Mineral oil is directly refined from crude oil without the addition of other additives. It is suitable for low-displacement, non-turbocharged vehicles or those with infrequent usage, typically around 5,000 kilometers in half a year. If you don't drive often, mineral oil offers the best economic value. Semi-Synthetic Oil: Semi-synthetic oil is a blended product made by mixing mineral oil and full synthetic oil through a compounding process. It offers the best cost-performance ratio and is a great choice for drivers who frequently use their cars. Its oil change interval is around 7,500 kilometers, making it suitable for most vehicle models. Full Synthetic Oil: Full synthetic oil is more expensive compared to the previous two types but offers superior performance. Whether in terms of stability, lubrication, low-temperature performance, or cleanliness, it far outperforms mineral oil and semi-synthetic oil. Its replacement interval exceeds 10,000 kilometers, and many car owners experience noticeable performance improvements after switching to full synthetic oil.
9
5
Share

Why does the screen go black when connecting Apple CarPlay to the car?

The main reasons for the black screen when connecting Apple CarPlay to the car are: In-vehicle computer crash: As modern cars have numerous electronic components, especially with the continuous updates of car connectivity systems, many vehicles' multimedia systems have become increasingly complex, leading to more frequent occurrences of dashboard screen malfunctions. You can try turning off and restarting the vehicle and its onboard computer to see if the screen display recovers. If the problem persists after repeated attempts, schedule a visit to a 4S shop for module inspection, software refresh, or repair. Connector detachment: Since many wiring connections use direct plug-in connectors, they may become detached or loose due to bumpy road conditions or original installation quality issues, resulting in dashboard screen failure. This can only be resolved by visiting a 4S shop or repair shop to disassemble the rear of the screen and securely reconnect the connectors.
10
1
Share

Why does the steering wheel shake when the car reaches 100 km/h?

In most cases, steering wheel vibration at 100 km/h is caused by wheel dynamic balance issues. The solution is to add counterweights to the wheels while they are in motion to correct the balance at various edge points - this process is called dynamic balancing. Other possible causes include shock absorber failure, frame deformation, or excessive clearance between the driving and driven gears of the final drive. It is recommended that owners regularly perform dynamic balance checks on their wheels. The dynamic balancing procedure is as follows: 1. Remove the logo in the center of the hub, install the dynamic balancer for measurement, and input the data. 2. Measure the rim width and input the data. 3. According to the computer-calculated data, add appropriate dynamic balance weights to both the inner and outer sides of the rim. When the re-test meets the standard, the process is complete.
18
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.