Where is the Low Beam Located?

1 Answers
VanJoel
07/29/25 11:13am
The switch for the low beam is generally located on the left side of the dashboard, near the door. Turning it one notch activates the low beam. The smaller bulb on the inner side of the front of the car is the high beam, while the larger lamp on the outer side is the low beam. Below are specific details about the low beam of motor vehicles: 1. Usage: The high beam is typically used when driving at night on roads without streetlights or with poor lighting, such as on dimly lit national highways or expressways. In urban areas with good lighting, the low beam must be used. 2. Related lighting change regulations: When passing under an arch bridge or a crosswalk at night, alternate between low and high beams; when passing through an intersection without traffic signals at night, alternate between low and high beams; when navigating sharp curves or slopes at night, flash the low and high beams alternately twice consecutively.
Was this review help?
2
0
Share
More Forum Discussions

Is the Lamando produced by SAIC or FAW?

Lamando is a compact car launched by SAIC, a Sino-German joint venture co-operated by SAIC Group and Volkswagen Group. It produces and sells products under the Volkswagen and Skoda brands, covering segments such as A0, A, B, C, SUV, and MPV. The Lamando is a compact car introduced by SAIC Volkswagen, with dimensions of 4615mm in length, 1826mm in width, and 1425mm in height, and a wheelbase of 2656mm. It is equipped with a 1.4T turbocharged engine with a maximum power output of 96kW, paired with a 7-speed dual-clutch transmission.
9
1
Share

Can Keyless Start Be Installed by Oneself?

Keyless start can be installed by oneself. Here are the relevant details: 1. However, most vehicle models require modifications to the original wiring during installation, and the installation costs vary for different models. Some models even require wiring modifications before the keyless entry system can be installed, which can be a significant expense. 2. Currently, there are plug-and-play options for one-button start modifications on the market, but most still require rewiring. If the modification is done at an unprofessional shop, there may be potential safety hazards. Therefore, vehicle owners who need this installation should choose products with quality assurance and have the installation done at a reputable modification shop.
14
1
Share

How to Eliminate Static Electricity When Opening Car Doors?

Methods to eliminate static electricity when opening car doors: You can discharge the vehicle's static electricity by carrying a metal object with you, or eliminate personal static electricity by wearing gloves or applying moisturizing products to your hands. Generally, winters are drier, and the clothes you wear are more prone to generating static electricity. Additionally, friction between the car and dry dust in the air can produce static electricity. To eliminate static electricity from the car, you can install an anti-static strip on the metal parts at the rear of the vehicle to discharge the static electricity to the ground. Car doors provide access for drivers and passengers, isolate external disturbances, and to some extent, reduce side impacts to protect occupants.
6
3
Share

Can You Keep Sport Mode On All the Time on the Highway?

You can keep Sport mode on all the time on the highway, but long-term use will definitely result in significantly higher fuel consumption compared to other driving modes. Simply put, Sport mode provides faster acceleration and stronger power by delaying gear shifts, allowing the engine to maintain higher power and torque output. With higher RPMs, the engine does more work in the same amount of time, making acceleration easier and quicker. In Sport mode, throttle response is faster and more sensitive, upshifts are delayed, and downshifts occur earlier, keeping the car in a highly aggressive state. The main downside of Sport mode is increased fuel consumption, with no other significant impacts. The additional wear caused by higher loads is negligible, as the effect is minimal.
15
1
Share

Why Do Motor Vehicles Need to Add Urea?

Automobiles require urea solution for the following reasons: Only diesel engines need to add urea solution because diesel engines emit polluting nitrogen oxide gases during operation. These gases are harmful to the atmosphere and human health. Prolonged exposure to such gases can cause respiratory diseases. Therefore, to reduce the damage caused by these gases to the atmosphere and humans, urea solution is required. This involves a catalytic reaction: when urea encounters the emitted nitrogen oxide gases, a chemical reaction occurs, converting the nitrogen oxides into nitrogen and water, which are harmless to the atmosphere and human health.
12
3
Share

How to Solve the No Signal Issue in Rearview Camera?

Rearview camera displaying 'no signal' indicates a signal loss, and the following wiring issues need to be checked. Below are the reasons and solutions for the no signal problem in rearview cameras: 1. Interference with the rearview camera operation may occur when the car is just started. Solution: Try restarting the system. 2. Electromagnetic interference from other electronic devices in the car. Solution: Try turning off the radio or music player before restarting. 3. Damage to the rearview camera's probe or obstruction of the chip's photosensitive signal due to prolonged use. Solution: Remove the camera and connect it to another navigation system to test if the camera is faulty.
11
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.