Where is the location of the air conditioning filter in the Volkswagen Tiguan L?

1 Answers
ChristianFitz
07/29/25 2:52pm
The air conditioning filter in the Volkswagen Tiguan L is located inside the glove compartment in front of the passenger seat. The specific steps for replacing the filter are as follows: 1. Open the glove compartment in front of the passenger seat and remove all items inside. 2. After removing the items, locate the fixing clip on the right side of the glove compartment and pull it off. 3. Once the fixing clip is removed, use both hands to squeeze the sides of the glove compartment inward, and the glove compartment can be taken out. 4. After removing the glove compartment, the air conditioning filter box will be visible. 5. Unscrew the screws on the air conditioning filter box and remove the foam cover. 6. After removing the foam cover, take out the old air conditioning filter. 7. Replace it with a new air conditioning filter and reassemble the glove compartment by following the disassembly steps in reverse order to complete the entire filter replacement process. Important notes regarding the vehicle's air conditioning filter: 1. Most vehicles require the air conditioning filter to be replaced every 5,000 kilometers or so; otherwise, it may affect the normal operation of the vehicle's air conditioning system. 2. Some air conditioning filters can be cleaned. 3. When replacing the air conditioning filter, ensure that the model matches the original factory specifications for the vehicle.
Was this review help?
15
5
Share
More Forum Discussions

Are there vehicle restrictions during the 2020 National Day holiday?

During the 2020 National Day holiday, there are no vehicle restrictions from October 1st to October 8th, a total of 8 days. However, it should be noted that October 10th (Saturday) is a working day, so please pay attention to your vehicle's license plate number when traveling to avoid violating the restrictions and receiving penalty points. Vehicles normally exempt from restrictions include: 1. Police cars, fire trucks, ambulances, and engineering rescue vehicles; 2. Public buses, interprovincial long-distance passenger vehicles, large buses, taxis (excluding rental vehicles), minibuses, postal service vehicles, and vehicles holding tourist bus operation certificates issued by the municipal transportation management department, as well as company shuttles and school buses approved by the municipal public security traffic management department; 3. Administrative law enforcement vehicles and special towing vehicles with unified markings performing duties; 4. Special operation vehicles for sanitation, landscaping, and road maintenance, as well as funeral vehicles from funeral parlors; 5. Vehicles with diplomatic license plates and vehicles approved for temporary entry.
5
0
Share

How to Deal with Water Leakage from Door Seals?

Water leakage from door seals should be addressed by replacing the seals or adjusting the door frame gap. Here is some relevant information about car seals: 1. The function of car seals: They not only prevent external objects from entering the car but also effectively stop rainwater from getting inside. Additionally, while driving, seals help reduce wind noise, vibration, and dust. 2. How to maintain door seals: Regular cleaning is essential. Owners should clean the seals every one to two months. Specifically, use a clean, damp sponge to wipe away dust from the tracks and grooves, then follow up with a dry sponge to ensure the seals remain clean.
15
3
Share

How is midway parking during parallel parking determined?

If the vehicle pauses for more than 2 seconds, it is considered midway parking. Below are the relevant details: 1. Determination of midway parking: During the Category 2 driving test, midway parking is determined when the GPS positioning confirms the vehicle is in a completely stationary state during the examination. 2. Methods to avoid midway parking: During the test, when passing over uneven ground or the joint seams of cement blocks in the test area, slightly increase the speed. When turning the steering wheel to full lock, slightly release the clutch to prevent midway parking; when returning the steering wheel, gently press the clutch to control the speed. Properly operate the clutch to maintain optimal vehicle speed.
2
3
Share

What Causes the Inner Door Handle to Not Open?

The inner door handle may not open due to the central locking system not being disengaged, the child lock being activated on certain doors, or a malfunctioning door lock switch. Below are specific reasons and solutions for the inner door handle not opening: 1. Central locking system not disengaged: Solution is to press the central locking switch on the driver's control panel to disengage the central lock. 2. Child lock activated on certain doors: Solution is to open the door from the outside, locate the child lock on the side of the door, and toggle the switch to deactivate the child lock.
20
5
Share

What does the white semicircular marking mean?

White semicircular markings are distance confirmation lines. The radius of the white semicircular distance confirmation line is 30cm, spaced at 50m intervals, and typically set continuously along certain road sections. Additional details are as follows:1. White parallel thick solid lines: Used to provide drivers with a reference for maintaining a safe driving distance, often used in conjunction with distance confirmation signs. These are placed in areas prone to overtaking, accidents, or other necessary sections. The purpose of highway distance confirmation markings is to remind drivers to maintain a safe distance from the vehicle ahead to prevent traffic accidents.2. White zigzag distance confirmation lines: These lines have a total width of 300cm, with line widths of 40cm or 45cm. Starting from the base point at 0m, they are placed every 5 meters, with two lines forming a group, spaced 50m apart, and repeated in five groups. Multiple groups may also be set based on site conditions.3. White rectangular distance confirmation lines: Used in conjunction with distance confirmation signs, these are placed in areas prone to overtaking, accidents, or other necessary sections. The purpose of highway distance confirmation markings is to remind drivers to maintain a safe distance from the vehicle ahead to prevent traffic accidents.
16
4
Share

Where is the volume button located in the car?

Volume buttons are generally located on the dashboard or sometimes on the steering wheel. Here is some related information: 1. Adjusting the volume: The car audio volume buttons are labeled VOL- and VOL+, which can be used to adjust the volume level. Car audio systems are designed to alleviate the monotony of travel for drivers and passengers, starting with car AM radios, followed by AM/FM radios, cassette players, and evolving to CD players and digital audio systems compatible with DCC and DAT. 2. Fully touchscreen center console: With the rapid advancement of automotive technology, car center consoles have also evolved silently. From traditional button operations to fully touchscreen modes, a fully touchscreen center console refers to the car's center console no longer using traditional physical button and knob designs. Instead, it employs capacitive touch technology, similar to smartphone screens, allowing users to complete operations with light touches, presses, or swipes.
7
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.