···
Log in / Register

Where is the lift mode button on the old Mercedes-Benz S350?

3 Answers
LaCody
07/29/25 3:56pm
The chassis lifting button for the old Mercedes-Benz S350 is located in the center console armrest area of the vehicle's cabin. Below is a relevant introduction: Chassis composition: The Mercedes-Benz S350 chassis consists of four parts: the transmission system, the driving system, the steering system, and the braking system. The role of the chassis is to support and install the car's engine and its components and assemblies, shape the entire vehicle, receive the engine's power to move the car, and ensure normal driving. Main functions: Its main function is to transmit the power generated by the car's engine to the drive wheels through the transmission system. The transmission system has functions such as deceleration, speed change, reversing, power interruption, inter-wheel differential, and inter-axle differential. Using the engine's operation ensures that the car runs normally under various working conditions, with good power performance and economy.
Was this review help?
2
5
Share
MorganMarie
08/15/25 3:54am
As a long-time owner of an older Mercedes-Benz, I remember the lift mode button for the S350 is typically located on the center console near the gearshift. There's usually a small button with an icon of a car and up/down arrows, which controls the air suspension height adjustment. Specifically, if you have an older S350 from the W220 era, say around 2003 model year, the button is positioned either beside the gear lever or in the lower left area of the instrument panel—designed to be discreet yet easily accessible. After starting the vehicle, pressing this button raises the chassis to handle rough roads, which is quite handy. However, note that if the vehicle doesn’t respond, it could be due to uninitialized suspension or sensor issues; in such cases, check if the fuse has blown. Older cars are indeed prone to such faults, so I recommend operating it while parked to avoid system damage, and regular maintenance of the suspension is crucial, especially the air springs and pump. Overall, don’t panic when searching for the button—just feel around the center console, and you’ll usually find it. If all else fails, consult the user manual.
Was this review help?
19
5
Share
Expand All
HaleyLynn
10/12/25 4:45am
I used to drive a used S350, and it took me a while to find the lift mode button. The button is usually located on the center console near the gear shift—a small round button with an upward arrow symbol, positioned within easy reach on the right side of the driver's seat. For older models around 2005, the operation is straightforward: press the button after starting the car to raise the chassis and avoid scraping the undercarriage. However, safety is key—make sure the car is completely stopped before pressing, as raising the suspension at high speeds can cause instability. If you can't find the button, don’t panic. Sometimes it might be faulty or obstructed, like by a cup holder cover. You can also check the car’s settings menu for hidden options. From my experience, maintenance issues like air leaks are common, so I regularly clean the button area to keep it dry and prevent corrosion. Overall, this feature is very practical in older Mercedes, especially for driving on rural roads, and the button’s placement is thoughtfully designed.
Was this review help?
18
0
Share
Expand All
More Forum Discussions

How to Solve Severe Black Dust on Car Wheels?

When the car is still new, it is necessary to frequently rinse the wheels. First, wet them with clean water, then scrub with a sponge using a cleaning agent, and finally rinse thoroughly with plenty of clean water. If the car has been driven for a while and regular cleaning and maintenance have been neglected, leading to a layer of hard coking on the rims, then a more powerful wheel cleaner should be used.
5
2
Share

How to Replace the Water in a Car Radiator?

Open the radiator drain valve to release the coolant, clean the cooling system, and continuously inject clean water into the engine cooling system. Close the cap, start the car, and let the engine idle for two to three minutes. The cooling system will expel internal air, and the coolant level will drop slightly. Maintain the liquid level between the max and min water level marks, tighten the radiator cap, and complete the coolant replacement.
6
5
Share

How to Deal with Marks on Car Exterior Paint?

Car marks can be cleaned with cleaning wax, provided that the water marks are still in the early stages and have not penetrated the paint. If water marks on the car paint cannot be wiped off, they can only be removed through polishing. However, it's important to note that while polishing can repair the paint surface, it is a consumable maintenance process. Cleaning wax and polishing are low-cost methods to deal with water marks on cars. If neither of these methods can remove the water marks, then a full car repaint is the only remaining option.
6
4
Share

How to Install a Belt on a Pulley?

Shorten the center distance to allow the belt to be properly installed; do not pry the belt into the pulley groove. Using tools to stretch the belt over the pulley groove can easily damage both the belt and the pulley groove. If a tensioner pulley is required on the transmission device, it must be installed with a grooved pulley supporting the inner side of the transmission belt, preferably on the slack side of the belt. The tensioner pulley should be positioned close to the large pulley. The movement range is determined after the transmission device is properly installed. During installation, the belt should at least fit over the outer diameter of one of the pulleys, and some elongation of the belt is permissible.
5
5
Share

How to Turn on the Mazda Fog Lights?

The front and rear fog light switches are located on the lower left side of the steering wheel. The fog light switch is on the inner side of the control lever and is operated by rotation. Rotate the fog light switch: turn it upward once to turn on the front fog lights, and turn it twice to the rear fog light position, which will simultaneously turn on both front and rear fog lights. Conversely, rotate it back to turn them off. After turning on the parking lights, you can then turn on the fog lights. The front fog lights can be turned on individually, while the rear fog lights can only be turned on together with the front fog lights and cannot be turned on separately.
16
3
Share

How to Align for Hill Start?

Align the center of the steering wheel with the center guide arrow on the slope, keeping the car body parallel to the lines on both sides; observe the right rearview mirror to ensure the car body is within 30cm of the roadside line. When the lower edge of the left rearview mirror aligns with the thick solid line, press the clutch and brake, pull the handbrake, and stop. Pay attention to the stopping position here. Release the handbrake and turn on the left turn signal. Slowly lift the clutch to the semi-engaged state. When you see the car body shaking, release the brake, and the car will climb the slope at a steady, slow speed.
10
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.