Where is the license plate number Ji E from?

1 Answers
VonBradley
07/29/25 4:05pm
Ji E is the license plate number for Xingtai City, Hebei Province. If you need to handle services such as license plate registration, annual inspection, or traffic violation processing, you can visit the Xingtai Vehicle Management Office. The English letters on the license plate represent the prefecture-level city code where the vehicle is registered. Generally, these codes are assigned by the provincial vehicle management office based on the status of each prefecture-level city, with A being the provincial capital, B the second-largest city, and so on. Below is relevant information about license plate numbers in Hebei Province: Shijiazhuang City (Ji A), Tangshan City (Ji B), Qinhuangdao City (Ji C), Handan City (Ji D), Xingtai City (Ji E), Baoding City (Ji F), Zhangjiakou City (Ji G), Chengde City (Ji H), Cangzhou City (Ji J), Langfang City (Ji R), Cangzhou City (Ji S), and Hengshui City (Ji T).
Was this review help?
15
1
Share
More Forum Discussions

How to Replace the Xenon Bulb in a 2010 LaCrosse?

Open the hood and locate the headlight position, then remove the dust cover; Disconnect the power connector, release the spring clip, hold the headlight socket and rotate the bulb counterclockwise to remove the socket; Insert the headlight socket into the lamp holder and reposition the spring clip. Insert the headlight bulb into the socket and rotate it clockwise to lock it in place; Tuck the driver and power cable into the assembly; Finally, replace the dust cover. Test the light to complete the installation.
3
4
Share

What to Do If You Accidentally Add Diesel to a Motorcycle?

First, it needs to be drained out. After mistakenly adding diesel, it is necessary to clean the fuel tank, fuel lines, and carburetor. Once diesel is mistakenly added, the motorcycle will immediately stall, and then experience difficulty starting.
11
1
Share

How to Properly Install a Motorcycle Carburetor?

First, thread the throttle cable through the carburetor top cover. Then, slide the spring onto the throttle cable. Next, pass the throttle cable through the throttle valve hole and pull it out from the adjacent slot, winding it all the way to the bottom. Finally, place the throttle cable head into the groove at the bottom of the throttle valve.
19
3
Share

How to Adjust the Air-Fuel Mixture Ratio of a Motorcycle?

Turning the mixture screw clockwise enriches the air-fuel mixture, typically by screwing it all the way in and then backing it out one and a half turns. Then, adjust the mixture screw left or right until the idle speed reaches its highest point. After that, fine-tune the idle speed to stabilize it.
5
1
Share

How to Check the Tire Wear Indicator Triangle?

To check the tire wear indicator triangle: 1. Locate the small triangular arrow mark on the side tread pattern of the tire; 2. Follow the mark to find the raised indicator in the groove of the tire tread; 3. When the tread depth is lower than the wear indicator, it means the tire is nearing the end of its life. Tire maintenance methods: 1. Ensure correct tire pressure; 2. Regularly check for bulges, cracks, cuts, punctures, or abnormal wear; 3. Inspect the tire surface for stones, nails, or other hard objects and clean them promptly; 4. Perform tire rotation. Tire rotation methods: 1. For bias-ply tires, swap the tires on the same axle to ensure even wear on both sides; 2. For radial tires, rotate them within the same side of the vehicle.
10
1
Share

What to Do When a Motorcycle Carburetor Leaks Fuel?

Pull out the float pin and remove the float and the triangular fuel needle. Insert a new all-metal triangular fuel needle of the same model into the needle valve seat. Use a small tool like a wrench to gently tap the tail end of the triangular fuel needle, creating an impact force on the needle valve seat.
16
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.