Where is the license plate number Gan E from?

1 Answers
JosiahFitz
07/29/25 12:25am
Gan E is the license plate number for Tianshui, Gansu. The license plate codes for various regions in Gansu are as follows: Gan A for Lanzhou, Gan B for Jiayuguan, Gan C for Jinchang, Gan D for Baiyin, Gan E for Tianshui, Gan F for Jiuquan, Gan G for Zhangye, Gan H for Wuwei, Gan J for Dingxi, Gan K for Longnan, Gan L for Pingliang, Gan M for Qingyang, Gan N for Linxia Hui Autonomous Prefecture, and Gan P for Gannan Tibetan Autonomous Prefecture. The first character of the license plate is a Chinese character representing the provincial-level administrative region where the vehicle is registered, which is the abbreviation of the province, municipality, or autonomous region. The second character is an English letter representing the prefecture-level administrative region where the vehicle is registered, which is the letter code for the prefecture-level city, district, autonomous prefecture, or league.
Was this review help?
5
3
Share
More Forum Discussions

How to Remove the Steering Wheel Airbag in a BMW 7 Series?

Method for removing the steering wheel airbag in a BMW 7 Series: 1. Release the steering wheel fixing lever. 2. Pull the steering wheel to its outermost position. 3. Start from the innermost part of the steering column cover, where there is a dust cover, lift the upper cover upwards and remove it. 4. Observe that the lower cover is also fixed with two clips on both sides, release the clips and remove it. 5. From the back, locate the airbag hooks on the steering wheel, use a T20 tool to pry on both sides, and pull the airbag outward. 6. Use a 15MM socket to directly remove it. Precautions for using the BMW 7 Series airbag are as follows: 1. It must be understood that the airbag is a one-time facility. After a collision, the airbag no longer has safety protection capability and must be replaced at a repair shop. The replacement equipment includes the airbag and a complete set of sensing and control systems. The price of airbags varies for different vehicle models. 2. Do not place other items in front of, above, or near the airbag. The airbag needs to be detonated in an emergency, which may eject these items and cause harm.
18
2
Share

Has the Mazda CX-5 been domestically produced?

Mazda CX-5 has been domestically produced, and this model belongs to Changan Mazda's domestic production. The following is relevant information about the CX-5: 1. The CX-5 is equipped with two engines, one is a 2.0-liter naturally aspirated engine, and the other is a 2.5-liter naturally aspirated engine. 2. The 2.0-liter naturally aspirated engine has a maximum power of 114kW, a maximum torque of 200Nm, a maximum power speed of 6000 rpm, and a maximum torque speed of 4000 rpm. This engine features direct fuel injection technology and uses an aluminum alloy cylinder head and block. 3. This engine is paired with a 6-speed automatic transmission. 4. The 2.5-liter naturally aspirated engine has a maximum power of 144kW, a maximum torque of 252Nm, a maximum power speed of 6100 rpm, and a maximum torque speed of 4000 rpm. This engine also features direct fuel injection technology and uses an aluminum alloy cylinder head and block. 5. This engine is paired with a 6-speed automatic transmission.
17
2
Share

At what engine temperature can the car's heater be turned on?

Engine coolant temperature reaching 90 degrees allows for heater activation. Below are temperature range explanations: 1. Only when the engine reaches 90 degrees will turning on the heater not increase fuel consumption, though the heater can be activated when coolant temperature reaches approximately 40-50 degrees. 2. For models without digital coolant temperature displays, observe the analog gauge's needle position - different vehicles have varying gauge designs, so identify when warm air begins blowing. 3. Generally not recommended to activate the heater below 50 degrees, as the system will blow cold air in low-temperature conditions.
17
1
Share

What Causes Steering Wheel Instability During Straight-Line Driving?

Steering wheel instability during straight-line driving occurs because the direction was not properly aligned before entering the straight path. If the steering wheel is not held firmly, it may wobble, and even slight movements can be detected as instability. Below are some tips for maintaining straight-line driving: 1. During straight-line driving, look far ahead and pay attention to both sides. Select a reference point to maintain a straight path, promptly correct the direction, and always be aware of traffic conditions ahead to respond in time. 2. "Look far but also stay aware of the near." Hold the steering wheel correctly, and adjust your focus distance based on speed. At higher speeds, look farther ahead; at lower speeds, focus slightly closer while using peripheral vision to monitor the vehicle's surroundings. 3. When correcting direction, make small, early adjustments—push and pull the wheel with both hands in coordination to keep the vehicle moving straight. If you feel the car veering, make minimal adjustments and immediately return the steering wheel to the neutral position.
17
0
Share

What Transmission Does the Bora Use?

The Bora model uses different transmissions depending on the variant. Specific details are as follows: 1. The 1.5L Bora model is equipped with a 6-speed automatic manual transmission (6AT). Compared to Volkswagen's dry dual-clutch transmission, this powertrain combination is more worry-free and durable. 2. The 1.4T model is paired with a 7-speed dual-clutch transmission (7DCT). The DSG used in the 1.4T is also Volkswagen's dual-clutch transmission. 3. The 1.6L model is configured with either a 5-speed manual transmission or a 6-speed automatic manual transmission (6AT). The 1.6 automatic version is equipped with Aisin's 6-speed automatic transmission from Japan.
9
5
Share

What Drives the Camshaft Through the Timing Gear?

The camshaft is driven by gears or chains. Here is an introduction to the camshaft: 1. It is a component in a piston engine, responsible for controlling the opening and closing of the valves. 2. Its material is generally special cast iron, though forged parts are occasionally used. 3. The valve movement pattern affects the power and operational characteristics of an engine. 4. The main body of the camshaft is a cylindrical rod approximately the same length as the cylinder group. It is fitted with several cams to drive the valves. 5. The camshaft is supported within the camshaft bearing holes via camshaft journals, so the number of journals is a crucial factor affecting the support stiffness of the camshaft. Insufficient stiffness may cause bending deformation during operation, affecting the valve timing.
2
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.