Where is the license plate Lu F from?

2 Answers
VanEvan
08/29/25 5:44am
Lu F is the license plate of Yantai City, Shandong Province. The license plate codes for cities in Shandong Province are as follows: Lu A for Jinan City, Lu B for Qingdao City, Lu C for Zibo City, Lu D for Zaozhuang City, Lu E for Dongying City, Lu F for Yantai City, Lu G for Weifang City, Lu H for Jining City, Lu J for Tai'an City, Lu K for Weihai City, Lu L for Rizhao City, Lu M for Binzhou City, Lu N for Dezhou City, Lu P for Liaocheng City, Lu Q for Linyi City, Lu R for Heze City, and Lu S for Laiwu City. Yantai is one of the prefecture-level cities in Shandong Province and is also the central city of the Shandong Peninsula in China, as approved by the State Council. It is an important port city in the Bohai Rim region and a national historical and cultural city.
Was this review help?
6
0
Share
RileyAnn
09/11/25 3:25am
During my last trip to Shandong, I specifically researched license plates, and Lu F is the code for Yantai. I remember Yantai is by the sea, so many vehicles with Lu F plates might have just transported seafood. The initial letters of license plates vary across Shandong Province, such as Lu A for the provincial capital Jinan, Lu B for Qingdao, and Lu C for Zibo. Yantai is quite economically developed, and there are many vehicles with Lu F plates, especially in the development zone where you can see a lot of Lu F new energy vehicles on the road. Understanding license plate regions is actually quite practical, especially when reviewing dashcam footage to quickly identify where other vehicles are from.
Was this review help?
20
4
Share
Expand All
More Forum Discussions

How to Determine the Maximum Speed of Car Tires?

The maximum speed a car can reach depends not only on the engine and the speedometer's upper limit but also on the speed rating of the tires. Here's an introduction to car tire speed ratings: 1. Different tire models have different speed limits. Exceeding these limits can significantly reduce the tire's lifespan and, in severe cases, cause a blowout at high speeds, leading to irreversible consequences. By carefully examining your tires, you can find their speed rating marked on them. 2. The rating indicates the tire's maximum speed. All tires display their size and various data, which are quite comprehensive. For example, the number 245 typically represents the tire's width in millimeters (245 mm), while 45% indicates the aspect ratio, which is the ratio of the tire's height to its width at the cross-section. 3. Tires also feature various letters indicating speed limits: The letter "Q" suggests a maximum speed of 160 km/h; "R" indicates 170 km/h; "S" denotes 180 km/h; and "T" represents 190 km/h. These are high-quality tires from reputable brands. The letter "H" signifies a maximum speed of 210 km/h, while "Y" indicates up to 300 km/h. Numerically, these are considered excellent tires.
8
5
Share

What maintenance is needed at 15,000 kilometers?

15000-kilometer maintenance falls between 10,000 kilometers and 20,000 kilometers. The main maintenance items include changing the engine oil and the three filters (oil filter element, air filter element, and cabin air filter element). Below is an introduction to engine maintenance: 1. Engine oil and engine oil filter element (also called engine oil filter), which are the most basic and essential items for every maintenance. The key is to maintain the lubrication system properly. Engine oil operates in a harsh environment of high temperature and high pressure, so its shelf life and performance will significantly decrease over time, and it will no longer provide protection for the engine. 2. Conventional engine oil needs to be replaced approximately every 5,000 kilometers; semi-synthetic engine oil, approximately every 7,500 kilometers; and full-synthetic engine oil, approximately every 1,000 kilometers. 3. Car maintenance refers to the preventive work of regularly inspecting, cleaning, replenishing, lubricating, adjusting, or replacing certain parts of the car, also known as car servicing. 4. The purpose of car maintenance is to keep the car clean, maintain normal technical conditions, eliminate hidden dangers, prevent faults, slow down the deterioration process, and extend the service life.
4
2
Share

What are the reasons for abnormal noise after replacing the timing belt?

Abnormal noise after replacing the timing belt could be caused by the timing belt being too tight, a damaged tensioner pulley, abnormal valve clearance, or misalignment/looseness of the timing pulley. When replacing the timing belt, pay attention to the following 4 points: 1. Selection based on different brands and mileage: The replacement interval varies depending on the brand and mileage, with most vehicles requiring replacement at 60,000-80,000 kilometers; 2. Not all vehicles require timing belt replacement: Not all vehicles need timing belt replacement, as some models never require it; 3. Consider both mileage and service years: In addition to mileage, the vehicle's service years should also be considered. Most vehicles require replacement every three years; 4. Choose authorized manufacturers for replacement: When replacing the timing belt, opt for authorized 4S shops and use genuine parts for safer and longer-lasting performance.
19
0
Share

Difference Between O-Ring Chain and Standard Chain?

An O-ring chain is designed to seal grease, isolating the lubricated components in the transmission system from the output components to prevent oil leakage. A standard chain refers to a series of metal links or rings used to obstruct traffic passages, such as on streets, river or harbor entrances, or chains used in mechanical transmissions. The differences between O-ring chains and standard chains can be summarized in three aspects: 1. Different classifications: (1) O-ring chain: O-rings are generally categorized into single-piece type and assembly type; (2) Standard chain: includes short-pitch precision roller chains, heavy-duty transmission curved plate roller chains, and chains for cement machinery. 2. Different service life: (1) O-ring chain: O-ring chains are durable, have a long lifespan, but are relatively bulky; (2) Standard chain: standard chains are more flexible but have a shorter lifespan compared to O-ring chains. 3. Different structures: (1) O-ring chain: each joint of an O-ring chain has an O-ring rubber seal on both sides of the shaft; (2) Standard chain: standard chains lack O-ring seals and cannot block sand, mud, water, or dust.
8
5
Share

How to Change Transmission Fluid with a Flushing Machine?

Flushing machine is a device that uses mechanical pressure to dynamically replace automatic transmission fluid, achieving a fluid replacement rate of over 80%. The operation process is simple but requires equipment support. There are 7 steps to change transmission fluid with a flushing machine: 1. Remove the undercarriage shield: Remove the shield and loosen the drain plug; 2. Expose the transmission: Expose the transmission and remove the oil pan; 3. Clean: Clean the oil pan; 4. Reinstall the oil pan and add fluid: Reinstall the oil pan and fill with transmission fluid; 5. Open transmission screw holes: Open the transmission drain and fill screw holes, then insert the flushing machine's inlet and outlet tubes into the transmission; 6. Start the vehicle: Start the vehicle and shift through all gears; 7. Observe the fluid inspection window: When the color in the inspection window turns clear red, the flushing process is complete.
10
3
Share

What are the symptoms of a faulty exhaust valve in an Audi A5?

A faulty exhaust valve in an Audi A5 can cause extremely unstable idling and even stalling. Impact on the engine: When the exhaust valve is damaged, it cannot control the amount of exhaust gas recirculation. Excessive exhaust gas recirculation will affect the mixture concentration, leading to symptoms such as difficulty starting the car, engine shaking, unstable idling, and weak acceleration, all of which impair engine performance. Engine oil consumption: A damaged exhaust valve can cause the car to burn engine oil, resulting in blue smoke from the exhaust pipe. The exhaust valve functions as an oil-gas separator. Under normal operation, it only draws in exhaust gas and not oil. When the exhaust valve is damaged, it loses its oil-gas separation function, potentially drawing in oil along with the gas, allowing oil to enter the combustion chamber and causing oil burning and blue smoke emissions.
17
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.