Where is the key induction area of the Envision located?

What Causes a Fuel-Injected Motorcycle to Suddenly Stall While Riding Normally?

Reasons include an empty fuel tank, abnormal fuel supply, excessively high engine temperature, electrical circuit failure, or a stuck clutch/other components. Below are detailed explanations: Empty fuel tank: Before stalling due to fuel exhaustion, the engine RPM will suddenly increase automatically (without throttle input). This phenomenon is easily noticeable at low speeds. Parking to check fuel levels can confirm this. Abnormal fuel supply: In this case, you'll feel gradual power loss before stalling. Check if the carburetor contains fuel. If empty, it indicates a clogged fuel line from tank to carburetor requiring cleaning. If fuel is present but the engine won't start, inspect the carburetor filter for blockage or dirty main jet. Excessively high engine temperature: Overheating causes poor lubrication, leading to piston-cylinder seizure and stalling. Check if lubricant is excessively depleted and replenish/replace promptly. Electrical circuit failure: Sudden power loss may result from loose connections, wire breaks or shorts. Inspect all connectors, clean oil contamination, and ensure stable contact. Poor trigger coil performance or loose solder joints may cause ignition failure - reinforce solder joints to eliminate poor connections. Stuck clutch/other components: When clutch support disk screws loosen (due to improper tightening or failed locking mechanisms), they may contact transmission countershaft bearing covers, causing clutch seizure and sudden stalling.

6

3

Share

What does the EPC light on the car display mean?

The EPC indicator light has two activation states: illumination during power-on self-test and illumination under other circumstances. The power-on self-test is an indication that the vehicle is checking the status of all sensors before driving. Generally, if the vehicle is not started after power-on, the light will turn off by itself after about 3 seconds. In other cases, if the EPC light remains illuminated after the vehicle is started, the main causes may include faults in the engine intake system, throttle valve, fuel system, engine, ECU control unit, or brake light. Below is a detailed explanation of the reasons for the EPC light illuminating under other circumstances: Engine intake system fault: The EPC light will activate if the engine intake is obstructed or insufficient. Throttle valve fault: Carbon buildup is a common issue with the throttle valve. Additionally, dirt accumulation can affect intake, triggering the indicator light. Fuel system fault: This includes issues such as substandard fuel, fuel deterioration, or poor fuel atomization. Engine fault: Insufficient engine pressure or problems with components like the intake valve in the powertrain can also cause the EPC light to activate. ECU control unit fault: Examples include interference with the vehicle computer signals or false alarms from the vehicle computer. Brake light fault: This includes situations where the brake light fails to illuminate, the brake switch malfunctions, or the brake wiring is faulty. Solutions for when the EPC light illuminates: Troubleshoot the intake system, use fuel with the appropriate octane rating, clean the throttle valve, etc. Remove carbon deposits from relevant components. Re-flash the ECU with updated data. If the EPC light illuminates, the owner can first try turning off the engine and restarting it to check if the light remains on. If it does not, there may be no issue, as the EPC light could have been affected temporarily. If the EPC light stays on or frequently illuminates, the vehicle should be taken to the nearest repair facility for professional diagnosis and timely resolution of potential safety hazards. The full English name of EPC is Electronic-Power-Control, which translates to electronic power control. Most people refer to it as the engine electronic stability system. The EPC system primarily includes controllers and sensors related to the powertrain. When sensor data in the system is abnormal, the EPC system will take predefined measures to address the powertrain issues. Common EPC indicator lights are typically displayed in two colors: yellow and red. A yellow EPC fault light indicates that the vehicle can still be driven, but it should proceed slowly to a repair facility for inspection. A red EPC fault light signifies a more severe issue, and the vehicle should be pulled over immediately while contacting a professional for repairs. Continuing to drive under such conditions may directly affect the vehicle's core components or compromise driving safety.

5

2

Share

Does Mirror Sweeping the Line During Reverse Parking Count as Passing?

Body sweeping the line means the vehicle body crosses the line, resulting in a 100-point deduction and failing the test. Other actions that also incur a 100-point deduction include the vehicle body crossing the line, not entering the garage, stopping midway, not following the prescribed route or sequence, and exceeding the time limit. The two subjects have a full score of 100 points, with evaluation criteria set for failing, deducting 20 points, deducting 10 points, and deducting 5 points. The rules for the Subject 2 test of the motor vehicle driver's license application state that stopping midway, rolling back, or not following the voice prompts during the test will result in failure. Additionally, wheels or the vehicle body crossing the line will also lead to failure. Many trainees encounter the issue of crossing the line during Subject 2 learning, with "crossing the line" being the most common reason for failure. The main cause of wheels crossing the line is the trainee not mastering the correct timing for steering. Apart from missing the steering timing, another reason could be the steering speed not keeping up with the vehicle speed. Subject 2 Deduction Standards: Not wearing a seatbelt: 100-point deduction. Starting the engine without the gear in neutral: 100-point deduction. Not using turn signals (including starting, changing lanes, overtaking, turning, and parking); turn signals not on for more than three seconds (note this is easily overlooked!); forgetting to turn off the turn signal or using it incorrectly: 10-point deduction. Stalling once: 10-point deduction. Reverse Parking: Not following the prescribed route sequence: 100-point deduction. Vehicle body crossing the line: 100-point deduction. Not entering the garage: 100-point deduction. Before reversing, not having both front wheels pass the control line: 100-point deduction. Exceeding 210 seconds to complete the task: 100-point deduction. Stopping midway for more than 2 seconds: 5-point deduction each time. Slope Fixed-point Parking and Starting: After stopping, the front bumper not positioned on the pole line and exceeding 50 cm front or back: 100-point deduction. After stopping, the front bumper not positioned on the pole line but not exceeding 50 cm front or back: 10-point deduction. After stopping, taking more than 30 seconds to start: 100-point deduction. Wheels touching the road edge line while driving: 100-point deduction. Rolling back more than 30 cm when starting: 100-point deduction. After stopping, the vehicle body more than 50 cm from the road edge line: 100-point deduction. After parking, not tightening the parking brake: 10-point deduction per time. After stopping, the vehicle body between 30 cm and 50 cm from the road edge line: 10-point deduction per time. Rolling back more than 10 cm but less than 30 cm when starting: 5-point deduction per time. Parallel Parking: After parking, the vehicle body crossing the line: 100-point deduction. Not using or incorrectly using turn signals when entering the garage: 10-point deduction. Exceeding 90 seconds to complete the task: 100-point deduction. Vehicle body touching the garage edge line while driving: 10-point deduction per time. Wheels touching the lane edge line while driving: 10-point deduction per time. Stopping midway for more than 2 seconds: 5-point deduction per time. 90-degree Turn: Wheels touching the road edge line: 100-point deduction. Not using or incorrectly using turn signals during the turn, or not turning off the turn signal after the turn: 10-point deduction. Stopping midway for more than 2 seconds: 5-point deduction per time. Curve Driving: Wheels touching the road edge line: 100-point deduction. Stopping midway for more than 2 seconds: 100-point deduction. Driving without the gear in second or higher: 5-point deduction.

17

3

Share

Reasons for Pajero Reverse Camera Malfunction?

Pajero reverse camera malfunction reasons are as follows: 1. The vehicle's camera is damaged or obstructed, requiring timely inspection, cleaning, or repair of the camera. 2. The display screen malfunctions, necessitating immediate testing and repair at a 4S shop. Below is an introduction to the reverse camera system: 1. When the reverse gear is engaged, the system automatically activates the high-definition rearview camera, clearly displaying the rear situation on the LCD screen. 2. The vehicle reverse camera is an integrated system, which can also be supplemented with in-car display devices.

14

2

Share

What does car ECO mean?

The ECO mode in cars refers to the Economic Driving Mode. Here is some relevant information about it: 1. The working principle of ECO mode mainly involves analyzing various configurations that affect fuel consumption, such as transmission gear position, braking system, and transmission oil temperature, through various sensors. Then, the ECU calculates the optimal amount of fuel to be supplied to the engine for operation, effectively reducing fuel consumption compared to normal driving mode. 2. When ECO is activated, the vehicle will make adjustments; the throttle opening corresponding to the same accelerator pedal depth will be smaller, and the transmission will shift up earlier. Simply put, the purpose is to control the engine speed through reasonable gear selection, reducing unnecessary fuel consumption.

14

4

Share

What are the common issues with Mitsubishi Lancer EX?

Every car has its own strengths and weaknesses. The common issues with Mitsubishi Lancer EX typically include: 1. Insufficient braking performance, with brakes being too soft and lacking power. 2. Occasional interior noises, such as rattling from the center console at high speeds. 3. Mediocre sound system performance with virtually no bass. 4. Rough craftsmanship, particularly in trim fittings that need improvement. 5. Thin body panels resulting in average safety performance. 6. Limited advantages in maintenance costs and resale value, with room for improvement in after-sales service, though basic performance remains adequate.

5

1

Share

Where is the key induction area of the Envision located?

What Causes a Fuel-Injected Motorcycle to Suddenly Stall While Riding Normally?

What does the EPC light on the car display mean?

Does Mirror Sweeping the Line During Reverse Parking Count as Passing?

Reasons for Pajero Reverse Camera Malfunction?

What does car ECO mean?

What are the common issues with Mitsubishi Lancer EX?

How long does it take for a new car to be inspected at a 4S store before delivery?

What are some affordable cars with sporty exhaust notes?

How Long Does It Take to Obtain a Vehicle License?

Can I use 12123 without carrying my driver's license and vehicle registration certificate?