Where is the interior trunk switch for the Highlander?

1 Answers
VonJackson
07/30/25 4:01am
The Highlander's trunk switch is located on the rear door, just above the license plate frame and below the decorative trim. There is no central control switch. Below are the specific details about the Highlander: 1. Vehicle Positioning: The Highlander is a large-sized SUV produced by Toyota. 2. Configuration: It is equipped with a 6.1-inch central control display screen with physical buttons on both sides, supporting basic Bluetooth multimedia entertainment systems. It also features the TSS (Toyota Safety Sense) intelligent safety assistance system, which includes PCS (Pre-Collision System), DRCC (Dynamic Radar Cruise Control System), LDA (Lane Departure Alert), and AHB (Automatic High Beam) functions.
Was this review help?
4
2
Share
More Forum Discussions

What is Vehicle Water Wading Insurance?

Engine water wading insurance refers to automobile damage insurance, also known as engine special loss insurance. Below is a detailed introduction about engine water wading insurance: 1. Overview: Engine water wading insurance is a newly derived insurance type, serving as an additional coverage purchased by car owners specifically for their vehicle's engine. 2. Function: It provides certain compensation when the engine is damaged due to reasons such as driving through waterlogged roads or being submerged in water. 3. Insurance Amount: Under normal circumstances, the insurance amount for engine water wading insurance is 50,000 Chinese Yuan. 4. Compensation Method: Each claim under water wading insurance is subject to a 15% absolute deductible rate. Compensation is based on actual repair costs within the insurance amount. When the cumulative claim amount reaches the insurance amount during the policy period, the insurance liability terminates.
11
3
Share

How to Reset the Maintenance Reminder for X-Trail?

X-Trail maintenance reminder needs to be reset manually. If it fails to disappear, you can connect a diagnostic computer to reset it. The manual reset steps are as follows: 1. Operate the toggle button and the confirm button on the left side of the steering wheel to enter the maintenance interface, click the maintenance option, then click the "Engine Oil and Filter" option. 2. Select the reset option below the number, then adjust the number on the right to 5000 kilometers, and click confirm to reset. Relevant information is as follows: 1. Do not ignore the warnings issued by warning lights and warning messages. For safety reasons, you should drive to the side of the road and stop for inspection and repair. 2. The red warning light indicates a dangerous fault. Once it lights up or flashes, you must stop and turn off the engine immediately, and inspect and repair the relevant systems of the car. 3. The yellow warning light is used to prompt or warn the driver to immediately check the relevant functions or perform relevant operations.
2
5
Share

What Are the Warning Signs of a Faulty Jetta Clutch Plate?

Here are the warning signs of a faulty Jetta clutch plate: 1. Feeling a decrease in the car's power, the car lacks strength. 2. The engine speed is high, but there is still insufficient power. 3. When starting, lifting the clutch feels uneven, the car has a jerking sensation, and there is a rough feeling when pressing, stepping, or lifting the clutch. Correct clutch usage methods: 1. When stepping on the clutch pedal, place the sole of your foot on the pedal with your heel touching the ground. When the clutch is pressed to the lowest point, keep the knee slightly bent. 2. Press the clutch to the lowest point. 3. Control the timing of the clutch. 4. Shift gears only after fully pressing the clutch pedal. 5. When pressing the clutch pedal, quickly release the accelerator pedal. 6. Ensure that clutch operation is coordinated with hand gear-shifting actions. 7. Avoid keeping your left foot on the clutch pedal while driving. 8. Under no circumstances should you use your right foot to press the clutch pedal while driving.
1
3
Share

How long does it take to get the driver's license after passing the subject 4 test in Weihai?

Some people can receive the license immediately after passing the test, while others may experience some delays, typically obtaining it within a week. In areas with lower efficiency, it might take a bit longer, usually around 15 days to get the license. Receiving the license after passing subject 4: After passing the subject 4 test, you are required to undergo at least 30 minutes of traffic safety and civilized driving education, including case studies of traffic accidents, and participate in a license oath ceremony. Only then will the vehicle management office issue the driver's license. Methods of receiving the license: There are several ways to receive the license: immediate issuance upon passing the test; mailing to the individual; picking it up at the driving school; or collecting it at the vehicle management office. Getting the license right after the test is the most convenient option. If immediate issuance is not available, choose the most convenient method for you.
19
5
Share

What are the consequences of not confirming the selected number on 12123?

If the car owner selects a license plate number in the 12123 system but does not confirm it, it will not affect the process of registering the plate at the vehicle management office. However, if the selection has already been confirmed, the owner must submit the required documents to the vehicle management office within the specified period to complete the registration. Failure to apply within the deadline will result in the automatic invalidation of the selected plate number, which will then be returned to the pool of available numbers. Consequences of not confirming a pre-selected number: If the owner fails to confirm the internet pre-selected license plate at the vehicle management office within the validity period, the user will be blacklisted and prohibited from pre-selecting a vehicle license plate online for 2 years, after which the blacklist status will be automatically lifted. Important notes for selecting a new license plate: It is highly recommended to first perform a simulated plate selection to familiarize yourself with all the steps and avoid selecting an unwanted plate due to operational or time constraints. There are restrictions on plate selection: you must confirm one out of 50 plate numbers. The selection is divided into 5 groups, with each group of 10 plates requiring a choice within 90 seconds. The selection area allows a maximum of 5 alternatives and must be confirmed within 180 seconds; otherwise, the selection will fail. Once a plate is successfully pre-selected online, if you wish to change it, do not wait until the 2-month registration validity period expires. If it expires, you will be blacklisted and unable to pre-select a plate online for 2 years. After successful online pre-selection, remember to register the plate promptly; otherwise, the plate will be reclaimed.
10
4
Share

Will I be fined if the rear left brake light is not working?

According to the "Road Traffic Safety Law" of China: Before driving a motor vehicle on the road, the driver should carefully check the safety technical performance of the vehicle; it is not allowed to drive a motor vehicle with incomplete safety facilities or components that do not meet technical standards, which may pose safety hazards. Check the brake light bulb: The most frequently used light on a car is the brake light, and the bulb has a relatively short lifespan. When the brake light is not working, the first thing to consider is the brake light bulb, and replacing the bulb can solve the problem. Check the brake light switch: If the brake light switch is faulty, all brake lights will not work. During inspection, you can use a wire to connect the brake light switch. If the brake lights turn on, it means the switch is damaged, and replacing the switch will fix the issue. Check the fuse: If both the bulb and the switch are confirmed to be working properly, the next step is to check the fuse. Some cars do not have a separate fuse for the brake light and share one with other electrical devices. In this case, you can check the operation of other electrical devices on the car. Identify any non-working electrical devices and replace the corresponding fuse.
13
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.