Where is the high beam relay located on the Cruze?

1 Answers
McAdalynn
07/30/25 5:35am
The high beam relay on the Cruze is located inside the engine compartment fuse box. After disassembling and separating the fuse box, you will find a circuit board where the black relay is the high beam relay. Taking the 2018 Cruze as an example, it belongs to the compact car category with body dimensions of 4666mm in length, 1807mm in width, and 1460mm in height, featuring a wheelbase of 2700mm, a fuel tank capacity of 52 liters, and a curb weight of 1240kg. The 2018 Cruze is equipped with a MacPherson strut front suspension and a torsion beam rear suspension. It is powered by a 1.5L turbocharged engine delivering a maximum horsepower of 114PS, a peak power of 84kW, and a maximum torque of 146Nm, paired with a 6-speed manual transmission.
Was this review help?
13
2
Share
More Forum Discussions

Is the Volkswagen Tiguan from FAW or SAIC?

The Volkswagen Tiguan belongs to SAIC's SUV models. The Volkswagen Tiguan features sharp and angular exterior lines, ample space, and is equipped with a panoramic sunroof. The trunk has a wide opening, and the interior is relatively conventional, with attention to detail in materials and craftsmanship. It also performs well in terms of fuel consumption, and the overall noise insulation is ideal. Here are some details about it: 1. Interior: The 2019 Tiguan L adopts Volkswagen's latest design language, with a polygonal design for the center console, moving away from the previous boxy and rigid style. The polygonal and multi-layered design highlights the sportiness and technological feel of the new Tiguan L. 2. Powertrain: The Tiguan L's 2.0T + 7-speed dual-clutch powertrain is already well-known and fully adequate for the vehicle's size. The turbo fully engages at around 1500 rpm, providing ample power feedback whether during acceleration or high-speed lane changes and overtaking. High-speed driving is generally maintained in the 80 km/h to 120 km/h range, with the engine and tire noise performance being quite ideal.
3
0
Share

What Causes Body Vibration After Accelerating by Pressing the Throttle?

Possible reasons for body vibration after accelerating by pressing the throttle are as follows: 1. Excessive carbon deposits and dirt near the throttle valve require timely cleaning. 2. Increased carbon deposits and dirt near the intake manifold, necessitating prompt cleaning of the intake manifold and inner channel walls. 3. Malfunction in the carbon canister area. 4. Low fuel pressure in the vehicle's engine, with clogged fuel injectors. 5. Issues with the engine's idle speed motor. 6. Problems in the engine's ignition system, requiring timely replacement of spark plugs. 7. Poor driving habits of the owner, with improper coordination between the clutch and throttle.
7
4
Share

How to Deal with Water Inside Headlights?

Methods for handling water in headlights are as follows: 1. First, inspect the headlight cover to check for any damaged areas. The presence of mist or water droplets inside the car's headlights indicates water ingress, and determining how the water entered the headlight is crucial. 2. If water ingress is due to a damaged headlight cover, the only solution is to drive to a repair shop for a replacement. If the headlight cover is intact, there's no need to worry. 3. Try to remove the water droplets and mist manually: You can drive the car outdoors and let it bask in the sun for half a day, relying on the sun's heat to evaporate the mist inside the headlights. If there's still residue, you can turn on the car's headlights. The headlights generate heat when turned on, which can also evaporate much of the mist. 4. Drive to a repair shop for inspection: Technicians can disassemble the headlights to clear out the mist and water droplets, check the headlights' sealing condition, and repair any damaged areas. They have the tools to inspect the headlight wiring and identify the source of the problem to properly fix the headlights.
16
5
Share

How to deal with cracked glass?

Check if it can be repaired, otherwise replacement is necessary. Whether damaged car glass can be repaired depends on two factors: 1. First, check the location of the damage point. Only damage in the whitish area of the glass can be repaired. If it's in a pitted or black adhesive area, it's unnecessary to repair, and it's recommended to replace the glass directly. 2. Second, assess the extent of the damage. If there are extended cracks within the main line of sight, it's advisable to replace the glass directly. If there are no extended cracks and the damage points are few and small, repair is possible. If there are extended cracks but they are not within the main line of sight and extend less than 10 cm, drilling and injecting adhesive to stop the cracks can be done. It's recommended to visit an auto beauty shop for an on-site evaluation to determine the best course of action.
2
2
Share

Where is the keyhole of the Haval H6?

Haval H6 mechanical key ignition keyhole is located on the car door handle. Here is some knowledge about car remote keys: 1. The car remote key is also the car's smart key, usually used in keyless entry systems. The smart key consists of a transmitter, remote central lock control module, driving authorization system control module, three receivers, and related wiring harnesses that form a control system. Through the signals emitted by the smart key, the car can enter a locked or unlocked state, and can also close the windows and sunroof. By emitting infrared signals through the smart key, the car's central locking system starts working to open the car door. 2. When the central processor senses that the key is inside the car, the one-button start button can be used to start the engine. The car smart key adopts the world's most advanced radio frequency technology and vehicle identity code recognition system.
8
3
Share

How to Defog a Car?

Methods for defogging and defrosting a car windshield are as follows: (1) Roll down the windows to allow air convection: Partially roll down the windows to let cold air from outside blow into the car, creating convection between hot and cold air. This reduces the temperature difference inside and outside the car, helping to eliminate frost and fog. If the weather is extremely cold, you can intermittently open and close the windows. (2) Use the air conditioning defogging system. The general steps are: 1. Adjust the "airflow mode" to "defog"; this mode mainly controls warm air to flow toward the windshield, the front windows near the rearview mirrors for both the driver and passenger. 2. Turn the "temperature control" knob to the red zone; this ensures the system outputs warm air. 3. Adjust the fan speed knob. To defog quickly, turn it to the maximum. Without airflow, the previous adjustments will not work. (3) Use a defogging agent.
18
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.