Where is the headlight height adjustment button for the 10th-generation Accord?

1 Answers
AmyLynn
07/29/25 4:06pm
The headlight height adjustment button for the 10th-generation Accord is located on the left side of the steering wheel and can be adjusted via a rotary knob. The 10th-generation Accord is a mid-sized 4-door 5-seater sedan under GAC Honda, with body dimensions of 4893mm in length, 1862mm in width, and 1449mm in height, a wheelbase of 2830mm, and a fuel tank capacity of 56 liters. The 10th-generation Accord is equipped with a 1.5T turbocharged engine and a CVT continuously variable transmission, delivering a maximum power of 143 kW and a maximum torque of 260 N·m. It features front-wheel drive, with a front MacPherson independent suspension and a rear multi-link independent suspension.
Was this review help?
9
1
Share
More Forum Discussions

How to Reset the Maintenance Light on the Lancer?

The method to reset the oil maintenance light on the Lancer is: 1. Turn the ignition switch to the ON position, and immediately press the button twice. 2. Turn the ignition switch to the OFF position. 3. When the ignition switch is turned to the ON position, press and hold the button simultaneously. 4. After 10 seconds, the new maintenance interval will appear on the display, accompanied by an audible signal. 5. Release button A6 and turn the ignition switch to OFF. Additional information: Engine oil that has a strong and unpleasant odor is either deteriorated or of poor quality and must not be used. In low-temperature winter regions, the fluidity of lubricating oil significantly decreases, increasing the engine's operational resistance. To protect the engine during this time, synthetic lubricating oil with good low-temperature fluidity should be selected. If the engine oil is not replaced on schedule, its various protective properties for the engine will significantly decrease or even disappear.
11
2
Share

How to Replace the Cabin Air Filter on a Baojun 730?

Baojun 730 cabin air filter replacement method mainly includes: 1. Locate the glove compartment on the passenger side and remove it. 2. Open the cover plate to access the filter, then pull out the old filter. 3. Install the new filter and reassemble in reverse order. Additional information: 1. The cabin air filter is installed in the vehicle's air conditioning system to absorb dust particles, alleviate respiratory discomfort, reduce irritation for allergy sufferers, and protect the air conditioning cooling system. 2. The Baojun 730 is an MPV model under the Baojun brand, with body dimensions of 4780mm in length, 1780mm in width, and 1740mm in height, with a wheelbase of 2750mm. 3. In terms of power, the Baojun 730 is equipped with two engines: a 1.5-liter naturally aspirated engine and a 1.5-liter turbocharged engine.
13
5
Share

How to Open a Zotye Car Key?

To open a Zotye car key, you will need a flathead screwdriver. There are gaps around the key, so you can pry it open along these gaps. The usual reason for opening a car key is to replace the battery. When replacing the battery, please note the following points: 1. Identify the positive and negative terminals of the battery correctly, with the positive terminal facing downward. 2. Avoid touching the circuit board or battery terminals during replacement. 3. Ensure that the electrode contact areas are free from dirt and grease. 4. After replacing the battery, test all functions of the key to ensure they work properly. If any issues arise, visit a repair shop for maintenance.
15
5
Share

How much transmission fluid does a Camry need?

Camry transmission fluid requirements are as follows: 1. For conventional gravity fluid replacement, less than 6 liters are needed; 2. For machine-assisted fluid replacement, approximately 12 liters of transmission fluid are required. Additional information: Transmission fluids are categorized into manual transmission fluid and automatic transmission fluid based on transmission structure. 1. Manual transmission fluid, commonly referred to as gear oil, is primarily composed of petroleum-based lubricating oil or synthetic lubricating oil, enhanced with extreme pressure anti-wear agents and oiliness agents. This essential lubricant is used in various gear transmission devices to prevent gear surface wear, scuffing, and seizing, thereby extending service life, improving power transmission efficiency, and reducing power loss. 2. Automatic Transmission Fluid (ATF) is specifically designed for automatic transmissions. This specialized fluid serves as the hydraulic medium for torque converters, the lubricant for planetary gear sets, and the hydraulic fluid for shift mechanisms. Under normal driving conditions, ATF should be replaced every 120,000 kilometers, while under severe driving conditions, replacement is recommended every 60,000 kilometers.
20
3
Share

How to Shift from D to L Gear in Sylphy?

The method to shift from D to L gear in Sylphy is as follows: 1. When driving at low speed, you can directly shift from D to L gear without stepping on the brake. Simply push the gear lever, press the shift button, or toggle the shift paddle. 2. When driving at high speed, such as around 80 km/h, shifting directly from D to L gear will cause the RPM to rise immediately, which can cause significant damage to the engine and transmission. It is advisable to step on the brake to reduce speed before shifting from D to L gear. Additional information: The Sylphy adopts Nissan's new design language in its exterior, making the overall appearance much sportier than the previous generation. The front face design is lower and more aggressive, with a V-shaped grille connecting the LED headlights on both sides, creating a strong visual impact. The design concept shares similarities with the Teana, hence it is nicknamed 'Little Teana'.
3
1
Share

What brand of tires does the Haval F7x use?

Haval F7x is equipped with Goodyear EfficientGrip series tires, with tire specifications 255/65R17 102H, 225/55R19 99H, and 225/55R19 99V. Here is some additional information: 1. Tires are circular elastic rubber products mounted on various vehicles or machinery to roll on the ground. Typically installed on metal rims, they support the vehicle body, absorb external shocks, ensure contact with the road surface, and maintain driving performance. 2. Tires often operate under complex and demanding conditions, enduring various deformations, loads, forces, and temperature extremes during driving. Therefore, they must possess high load-bearing capacity, traction performance, and shock absorption. Additionally, they require excellent wear resistance, flexibility, and low rolling resistance with minimal heat generation. As the only component in direct contact with the ground, tires play a crucial role in vehicle performance.
12
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.