Where is the handbrake of the Highlander located?

What is Fuel Injection Timing?

Fuel injection timing refers to the correct fuel supply time of the injection pump, generally expressed by the fuel injection advance angle. The fuel injection advance angle is the crankshaft rotation angle from when the No.1 cylinder plunger of the injection pump begins supplying fuel until the piston of that cylinder reaches top dead center. Below is the relevant introduction: The fuel injection advance angle is the crankshaft rotation angle from when the No.1 cylinder plunger of the injection pump begins supplying fuel until the piston of that cylinder reaches top dead center. Generally, the fuel injection advance angle for diesel engines is 15-25°. If the fuel injection advance angle is too large or too small, it will affect the engine's working performance. When a vehicle has traveled a certain mileage or after the injection pump has been overhauled and reinstalled during maintenance, the fuel injection timing must be checked and adjusted to ensure the diesel engine operates under the optimal or near-optimal fuel injection advance angle.

11

0

Share

Do LED Headlights with Fans Require Dust Covers?

LED headlights with fans require the installation of dust covers. Universal dust covers can be used, which are designed to expose the heat dissipation or fan of the LED headlights. This solution addresses both dust prevention and heat dissipation, providing a better cooling environment. Automotive dust covers are protective accessories used to prevent dust accumulation on vehicles. They are primarily installed on steering mechanisms, drive shafts, and other widely distributed areas such as handbrakes, foot brakes, throttle linkages, master brake cylinders, and wheel cylinders. Advantages of LED headlights with fans: Fan cooling is an active heat dissipation system, offering higher cooling efficiency. Due to fan cooling, the heat from the headlights can be distributed promptly, lowering the temperature and thereby increasing brightness. With fan cooling, the new three-sided LED headlights achieve exceptionally high brightness.

16

1

Share

What to Do If the Fuel Pump Cover is Leaking?

The solution for a leaking fuel pump cover is: If the car is leaking engine oil, replace the sealing gasket; if it's leaking gasoline, the high-pressure fuel pump must be replaced. The reasons for a leaking fuel pump cover include: 1. The sealing gasket at the junction between the fuel pump and the crankcase is too thick; 2. The pump diaphragm is ruptured, or the seal between the diaphragm and the upper housing of the pump is not tight; 3. The inlet and outlet valves are stuck or have poor sealing; 4. Severe wear of the rocker arm reduces the diaphragm's stroke; 5. The pipeline from the fuel tank to the fuel pump is obstructed, or the diaphragm spring is faulty. The fuel pump is a component that draws gasoline from the fuel tank and delivers it through pipelines and the fuel filter to the float chamber of the carburetor. Based on the driving method, fuel pumps can be divided into two types: mechanically driven diaphragm type and electrically driven type.

17

2

Share

What Causes the Vehicle Stability Control System Indicator to Light Up?

It may be that the electronic stability program (ESP) has been turned off. The ESP consists of the following four components: 1. Sensors: including steering sensors, wheel sensors, skid sensors, acceleration sensors, and sensors for the steering wheel, throttle, and brake pedals. These sensors are responsible for collecting data on the vehicle's status. 2. ESP computer: It calculates the data collected by the sensors to determine the vehicle's status and compares it with pre-set data in the memory. When the computer calculates that the data exceeds the pre-stored values in the memory, indicating that the vehicle is nearing or has already lost control, it commands the actuator to work to ensure the vehicle's driving state aligns as much as possible with the driver's intentions. 3. Actuator: The ESP's actuator is the braking system of the four wheels. Unlike vehicles without ESP, vehicles equipped with ESP have a braking system with pressure accumulation capability. 4. Communication device: The ESP light on the dashboard serves mainly as a warning to prevent safety accidents.

17

2

Share

How Many Kilometers Should the CVT Transmission Steel Belt Be Replaced?

CVT transmission steel belts should generally be replaced after approximately 100,000 kilometers of use. If during driving, severe transmission jerking or loud noises are noticed, it indicates aging of the transmission steel belt, and immediate attention at a 4S shop is required. Most modern CVT transmissions in cars use a steel belt for power transmission. This method allows for changing the transmission ratio by adjusting the size of the pulleys, enabling it to handle greater torque. The working principle of a CVT transmission involves altering the size of the cone pulleys to affect the vehicle's transmission ratio, with power then transmitted via the steel belt or chain. CVT chains are generally less durable than steel belts in practical use. Although CVT chains exert less impact on the cone pulleys, their strength is inferior to that of steel belts, making chain-based CVTs unable to withstand higher torque. While steel belts may generate more noise, they can handle greater torque and offer better durability.

19

1

Share

Why don't Japanese cars use cavity wax injection?

Japanese cars generally use sealing strips and mostly do not employ cavity wax injection. Cavity wax injection involves injecting a certain amount of liquid wax into the four cavities at the bottom of the car body. Through specific technical processes, the wax remaining inside the body cavities forms an even protective wax film, preventing water droplets from seeping in and ensuring excellent anti-corrosion performance for the entire vehicle. Here is more detailed information: 1. Function of cavity wax injection: In addition to preventing corrosion, cavity wax injection can also enhance the stability of the vehicle during operation, thereby correspondingly reducing fuel consumption and indirectly improving the overall fuel economy of the vehicle. 2. First adoption: Volkswagen was the first automaker in China to introduce cavity wax injection technology. Models such as Shanghai Volkswagen's POLO, Touran, Superb, and Lavida, FAW-Volkswagen's Magotan, Sagitar, and Golf, as well as the entire Audi lineup, all feature cavity wax injection.

4

5

Share

Where is the handbrake of the Highlander located?

What is Fuel Injection Timing?

Do LED Headlights with Fans Require Dust Covers?

What to Do If the Fuel Pump Cover is Leaking?

What Causes the Vehicle Stability Control System Indicator to Light Up?

How Many Kilometers Should the CVT Transmission Steel Belt Be Replaced?

Why don't Japanese cars use cavity wax injection?

What are the hidden features of the Haval H6 Platinum Champion Edition?

How to Set Up the Hidden Feature of Horn Sound When Locking the Tiguan L?

What does active grille shutter mean?

What are the contents of the manual transmission test in Subject 2?