Where is the handbrake located on a Toyota Crown?

What to Do If One Reversing Radar is Broken?

Since the four sensors of the reversing radar operate independently, if one is damaged, you only need to replace the faulty reversing radar. First, you can check whether the power cord of the radar host is properly connected and if there is current supply. Also, check if the radar host wire is loose. If both are fine, the issue might be a damaged buzzer. Below is a detailed introduction to the reversing radar: The reversing radar typically has four sensors, installed at the rear or both sides of the car, with two on each side. Also known as a reverse parking sensor or parking aid, the reversing radar is a safety assist device used when parking or reversing. It consists of ultrasonic sensors, a controller, and a display (or buzzer). The reversing radar system alerts the driver about surrounding obstacles through sound or a more intuitive display, making reversing and parking safer. When the gear lever is shifted into reverse, the reversing radar automatically activates. When a sensor detects an object behind the vehicle, it emits a beeping sound as a warning. As the vehicle continues to reverse, the frequency of the alarm sound gradually increases, eventually turning into a continuous tone.

20

5

Share

Where is the button to drain the windshield washer fluid?

Lift the car up, and there is usually a reservoir located below the right front wheel. Remove the small tube to drain the fluid. Here is some relevant information about windshield wipers: 1. Operating Principle: The power source of the wiper comes from an electric motor, which is the core of the entire wiper system. The quality requirements for the motor are quite high. Typically, a DC permanent magnet motor is used, and the wiper motor installed on the front windshield is usually integrated with the worm gear mechanism. The worm gear mechanism serves to reduce speed and increase torque. Its output shaft drives a four-bar linkage, which converts continuous rotational motion into a left-right oscillating motion. 2. Basic Introduction: The wiper is a blade structure installed in front of the windshield, consisting of an electric motor, reducer, four-bar linkage, wiper arm spindle, and wiper blade assembly. Its main function is to clear rain, snow, and dust that obstruct the view on the windshield.

4

1

Share

Should I go to a 4S shop or an outside garage for car maintenance?

The second type of maintenance that should be done at a 4S shop is touch-up painting. In fact, the quality of touch-up painting at a 4S shop is far superior to that at outside repair shops. Here is some related information about car maintenance: 1. First maintenance: Some manufacturers set the first maintenance based on time or mileage. The exact timing for the first maintenance should be based on the vehicle's user manual or warranty manual. The first maintenance is very important and is free, so be sure to remember to do it to avoid missing it and affecting the car's three-year warranty. 2. Maintenance items: Main car maintenance items include changing the engine oil, oil filter, transmission oil, spark plugs, air conditioning filter, air filter, brake fluid, etc. However, not all of these need to be changed every time, as it depends on the lifespan of the oil. In addition, maintenance also involves the inspection and upkeep of dozens of items across multiple systems, including the engine, transmission, air conditioning system, steering system, braking system, suspension, body, and tires.

5

1

Share

How to Identify Genuine Automotive Explosion-Proof Film?

Methods to identify genuine automotive explosion-proof film: 1. Observe the color: Explosion-proof films typically use eye-friendly colors such as light green, sky blue, gray, brown, or natural tones. 2. Smell the odor: Inferior films often contain high levels of benzene in their adhesive layers, resulting in a noticeable unpleasant smell. 3. Feel the texture: Genuine safety explosion-proof films are generally at least 2.5mm thick, providing a thick and smooth tactile feel. The functions of automotive explosion-proof film are as follows: 1. Prevent glass cracking and interior fading: Besides harming the driver's skin, prolonged exposure to UV rays can cause glass to crack and car interiors to fade. Explosion-proof film helps extend their lifespan. 2. Thermal insulation: In summer, it blocks external heat, keeping the car interior cooler, while in winter, it retains interior warmth. 3. Enhance anti-violence performance: Automotive explosion-proof film improves vehicle safety during accidents, minimizing the risk of glass shattering and reducing potential harm to passengers. 4. UV protection: The film blocks over 90% of UV rays, preventing skin burns.

5

0

Share

What Are the Reasons for High Engine RPM but Low Speed in Motorcycles?

Motorcycles experiencing high engine RPM but low speed can be attributed to the following reasons: 1. Clutch Slippage: Poorly adjusted or inherently flawed clutch designs may cause slippage during high-speed riding when resistance increases, accompanied by abnormal friction noises, especially when climbing hills. 2. Insufficient Power: Apart from severe cylinder wear leading to air leakage, worn piston rings causing compression loss, or inadequate carburetor fuel supply, carbon buildup blocking the exhaust pipe or cylinder exhaust ports significantly impacts engine maximum power and RPM. Some motorcycles may also suffer from carburetor fuel starvation during high-speed operation. 3. Improper Transmission: Rear chain-driven motorcycles with excessively high gear reduction ratios exhibit strong low-gear acceleration but suffer from limited top speed and fuel efficiency in higher gears. Scooters may fail to achieve maximum front variator pulley diameter, remaining in low-RPM riding conditions. 4. Poor Vehicle Condition: Excessive wind resistance due to bulky bodywork, brake shoes sticking to drums, tires caked with mud, or severely underinflated tires all contribute to this performance issue.

11

3

Share

When is the implementation time of China VI emission standards?

China VI is divided into two standards, each with its own implementation time. The following are the two classifications of China VI: 1. China VI a. From July 1, 2020, light-duty vehicles will be required to comply with the China VI a emission standard. 2. China VI b. From July 1, 2023, light-duty vehicles will be required to comply with the China VI b emission standard. However, many provinces and cities have already implemented these standards ahead of schedule, and the implementation time may vary according to local regulations: 1. Guangzhou: Light-duty vehicles will implement China VI from January 1, 2019. 2. Jiangsu: All gasoline supplied will meet China VI standards from October 1, 2018. 3. Guangdong: China VI diesel fuel has been available since July 1, 2019. 4. Shandong: The China VI emission standard for motor vehicles will be implemented province-wide from July 1, 2019. 5. Shenzhen: China VI will be fully implemented from January 2019, and fuel vehicles with emissions below this standard will be restricted from sale, purchase, and road use.

7

1

Share

Where is the handbrake located on a Toyota Crown?

What to Do If One Reversing Radar is Broken?

Where is the button to drain the windshield washer fluid?

Should I go to a 4S shop or an outside garage for car maintenance?

How to Identify Genuine Automotive Explosion-Proof Film?

What Are the Reasons for High Engine RPM but Low Speed in Motorcycles?

When is the implementation time of China VI emission standards?

How many liters of transmission oil should be added to the Volkswagen DQ250 transmission?

How Long Does the Law Define a Car as Stock Vehicle?

Can I transfer to another driving school after registration?

What to Do When Engine Oil Pressure is Insufficient?